Panasonic NNV70092WE1A LED Down Light Instruction Manual
- June 16, 2024
- Panasonic
Table of Contents
Panasonic NNV70092WE1A LED Down Light
(Please refer to the specification table)
To users
Thank you for choosing our products. Before using this product, please read
this instructions carefully and keep it.
Safety precautions
Please strictly adhere to the following instructions must be strictly followed in order to prevent damage to the body and property.
Danger
- Do not cover the lamp with thermal insulation material
- Luminaires are not suitable for covering with thermally insulating material
- Avoid causing fire accident
Leave a space between the appliance and thermal insulation materials, sound Avoid fire accidents.
Warning
- Please install strictly according to these instructions. Improper installation may result in the falling of the product, electric shock, fire, or accidents.
- This product is for embedded ceiling installation. Please don’t install it at the following locations.
- Thin ceilings with poor strength.
- Soft asbestos ceiling.
- Oblique ceiling.
- Wall.
- To avoid electric shock, fire, and falling of the product.
- Don’t use a dimming device, such as a brightness dimming switch, light controller, eel, or other such devices to avoid a fire.
- In case of any normality, please immediately cut off the power to avoid a fire.
- Please do not modify the lamp and change parts.
- The power supply should be in the specified value (Rated voltage 220V-240V-) Long-time operation exceeding this voltage range may lead to an accident or damage caused by overheating.
- It is not advisable to install the lamp directly on the surface of normally flammable material.
- The external flexible cable or flexible wire of the product shall not t>e replaced. If the flexible wire is damaged, the lamp shall scrapped.
Warning
Notice
- Terminal block not included. installation must be performed by a qualified person.
- Don’t use the product in bathrooms, moist locations, as well as outdoors. The product is nonwaterproof. Improper installation may cause poor insulation, electric shock, fire, injury, eel.
- Please cut off the power when performing maintenance to avoid electric shock.
- Don’t put objects with high temperatures like electric warming ovens or gas cookers under the product to avoid a fire.
- Don’t stare at the LED light source to avoid eye damage.
- The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
- The LED light source has chromatic aberration. The photochromatic and brightness of different products vary from each other.
- Please cut off the power when the product fails to light and contact the distributor or after-service department to avoid electric shock.
PREPARATION
Preparation prior to Installation
Embedding Hole Specification
- Before Installation, please make sure to take down the packing accessories.
- Before Installation, make sure to take down the packing accessories and tape from the lamp to avoid a fire.
- Ensure the installation position on the ceiling is strong enough to bear the weight of the lamp.
- To avoid causing lamp falling or other accidents.
- Open inserting holes on the ceiling by reference to the hole size provided in the confirmation items before installation.
Names of parts and installation methods
Installation diagram (takeNNV70090WE1A for example
Connect the power cord
To ensure safety, please be sure to cut off the power, before connecting
the external power wire.
- It is recommended to use a terminal block with a shell for wiring. (The shell and terminal block shall be separately purchased) Please connect the power cord of the lamp and the external power cord correctly on the terminal block.
- After the connection, the brown and blue wires shall not be exposed outside the shell of the terminal block.
- The terminal block shall not be placed on the lamp.
- Do not use threaded nail wire terminal
- Improper connection may cause accidents such as fire and electric shock.
2pins screwless terminal block is used and it shall comply with IEC 60998-2-2;
- Rated voltage: 250V-;
- Rated connecting capacity: 0.5-1.5mm2
- Wire preparation: Wire stripping length 7-8mm
Installation and removal of the product
- Press the springs on both sides of the lamp upward at the same line along the direction of the arrow.
- Push the lamp upward into the inserted hole
- Insecure installation may cause lamp falls and other accidents.
- Dismounting method: Use both hands to pinch the external edge of the external frame, and then pull the lamp downwards vertically to dismount it.
- When dismounting the lamp, use your hands to press against the spring, so as to avoid it rebounding and hurting your hand.
Lamp color temperature adjustment
- The lamp can adjust the color temperature: Cool Daylight(6500K)-Warrn White(3000K)-Cool White(4000K).
- When the wall switch turns on for the first time, the lamp is on with the condition of Cool Daylight(6500K).
- Turn off the wall switch and then turn it on quickly (within about 11 seconds) for the lamp color temperature adjustment, please refer to G) for the adjustment method.
- If the operating wall switches too fast, it may not adjust the lamp color temperature.
- Turn off the wall switch (more than about 11 seconds) then turn it on, until the lamp is on in the initial condition (Color temperature 6500K).
- When there are two or more lamps, because the 4 conditions may happen, it may occur the condition that several lamps have different color temperatures.
- When 6 conditions occur, please turn off the wall switch (more than about 11 seconds) and then turn it on again.
Maintenance
Cut the power to avoid electric shock
- In order to use this product safely and efficiently, please clean and check it regularly (once every 6 months).
- Lack of maintenance may result in electric shock, fire, personal injury, etc.
- When the product is dirty and requires cleaning, please wipe it with a soft cloth that has been moistened in soapy water, followed by a dry cloth.
- Clean with soap and water only. Don’t clean with pesticides, etc to avoid color fading, deterioration, strength reduction, and damage to the product.
This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.
Specifications
Specifications of Product
- The style and color of the actual lamp shall prevail.
- The information may be subject to change without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>