MOUNTUP MU0063 Ultra Slim TV Wall Mount Instruction Manual

June 16, 2024
MOUNTUP

MOUNTUP MU0063 Ultra Slim TV Wall Mount

Safety Caution

Please read this instruction carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.

  • ● This product is designed for use in wood stud or solid concrete wall.
    • DO NOT install into drywall alone.
  • The wall must be capable of supporting five times the weight of the TV and mount combined.
  • Incorrect installation may result in product damage / property damage or body injury. We shall bear no responsibility for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.

WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; please contact our customer service team. Never use damaged parts!

Must Check Before Getting Started

Minimum VESA Pattern (W × H):
100mm × 100mm / 4 in × 4 in
Maximum VESA Pattern (W × H):
600mm × 400mm / 24 in × 16 in

MAX:
99 lbs (45 kg)

DO NOT exceed the maximum weight indicated. This mounting system is intended for use only within  the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the mount and its accessories, causing possible damage or injury.

Verify Your Wall Construction


Perfect!
CAUTION:

Avoid potential personal injuries and property damage! Drywall covering the wall must not exceed 5/8 in. (16 mm). Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1 ½ x 3 ½ in. (38 x 89 mm).


Perfect!
CAUTION:
Avoid potential personal injuries and property damage! Mount the wall plate assembly directly onto the concrete surface (no surface covering).

DO NOT install into drywall alone.

Product Dimensions

Supplied Parts and Hardware

Lag Bolt
ST8×60mm

|

Washer
Ф8mm

|

Bolt
M5×6mm

|

Allen Key
4mm

|

Bubble Level

---|---|---|---|---
| |

TV

Philips Screws
M4 x 12mm
M4 x 30mm

| Philips Screws
M6 x 15mm
M6 x 30mm| Philips Screws
M8 x 25mm
M8 x 45mm| Spacers
H10mm| Washers
Ф6mm
M4-5-6|

Spacers
H5mm

---|---|---|---|---|---
| | | | |

NOTE: Not all parts and hardware included will be used.

Extra Tools You Need (Not Supplied)

  • Band Tape

  • Pencil

  • Electro drill

  • Socket Wrench

  • Screwdriver

Select TV Screws and Spacers

Select TV Screws

Need Spacer?

  1. No, just choose the screws, washers.

  2. Yes, choose the appropriate screws, washers,and spacers for your TV

    • For more spacing between bracket and TV

    • For protruded back TV

    • For counterbore of TV

    • To avoid the blocked input

NOTE: You can add spacers or use upper mounting holes to get more bottom space.

Attach Brackets to TV

Assemble Wall Plate

Connect two wall plates 01 by using connecting plate 02 and M5 screws B. Use the screwdriver to tighten the screws.

Attach Wall Plate to Wall

OPTION A:
Wood Stud Installation

Locate your studs. Verify and mark the center of the stud by finding the stud edges using awl and stud finder.

Line up the holes with your stud center line. Level the wall plate and mark the pilot hole locations.

Drill pilot holes using a Ф7/32 in (Ф5.5mm) diameter drill bit.

IMPORTANT:
Do not drill holes into where water pipes or electrical wires are located. Be sure to drill into the center of the stud.

Install wall plate using lag bolts A with Socket Wrench, NO Electrodrill. No anchors when installed onto the wood studs.

CAUTION:

To avoid potential personal injury or property damage:
All 2 lag bolts A MUST BE firmly tightened to prevent unwanted movement of the wall plate assembly. Ensure the wall plate assembly is securely fastened to the wall before continuing on to the next step.

Attach Wall Plate to Wall

OPTION B:
Solid Concrete Wall Installation

Level the wall plate and mark the pilot hole locations.

Drill pilot holes using a Ф3/8 in (Ф10mm) diameter drill bit.

IMPORTANT:
Do not drill holes into where water pipes or electrical wires are located, or mortar between blocks.

Use the hammer to knock anchors (not included) into the concrete wall. Be sure the anchors are seated flush with the concrete surface.

Install wall plate using lag bolts A and anchors (not included) with Socket Wrench, NO Electrodrill.

CAUTION:

To avoid potential personal injury or property damage:
All 2 lag bolts A MUST BE firmly tightened to prevent unwanted movement of the wall plate assembly. Ensure the wall plate assembly is securely fastened to the wall before continuing on to the next step.

Hang and Secure TV to Wall Plate

Before hanging TV, please conduct “wall plate installation integrity test” first.

Hang and secure TV assembly onto the wall plate

NOTE: Please plug in the cables before hanging up the TV.

  • Pull and hold the straps down

  • Hang TV assembly onto the wall plate

  • Release the  straps up

Keep pulling the straps while hanging/taking down the TV.

If necessary Take down the TV from the Mount

  • Pull and hold the straps down

  • Lift TV assembly up vertically

  • Pulling the TV away from the wall

Keep pulling the straps while hanging/taking down the TV.

Adjustments (If necessary)

Tool-free Tilting Adjustment

Cable Management

Straps Management

Customer Support

If you have any questions, please feel free to contact our customer support before returning.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals