2024 Durango

Product Information

Specifications

• Product Name: 2024 Durango
• Manufacturer: FCA US LLC
• Services: Flat Tire Service, Out Of Gas/Fuel Delivery, Battery
  Jump Assistance, Lockout Service and Towing Service

Introduction

The 2024 Durango is a versatile vehicle designed to meet your
needs. This owner’s manual provides important information about the
features and usage of your vehicle.

Getting to Know Your Vehicle

Keys

The 2024 Durango comes with a Key Fob that allows you to lock
and unlock your vehicle remotely. The Key Fob is an essential
component for operating your vehicle.

Sentry Key

The Sentry Key is a security feature that provides an additional
layer of protection for your vehicle. It uses a unique code to
prevent unauthorized access.

Ignition Switch

The ignition switch is used to start and stop the engine of your
vehicle. It is an important component that should be used with
caution.

Keyless Enter ‘n GoTM Ignition

If equipped, the Keyless Enter ‘n GoTM Ignition feature allows
you to start your vehicle without inserting the key into the
ignition switch. Simply press the Start/Stop button to start or
stop the engine.

Remote Start

If equipped, the Remote Start feature allows you to start your
vehicle remotely, from a distance. This can be useful for warming
up or cooling down the interior before entering the vehicle.

How To Use Remote Start

To use the Remote Start feature, follow these steps:

1. Press the Remote Start button on your Key Fob twice within five
   seconds.

2. The vehicle will start, and the engine will run for a
   predetermined amount of time.

To Exit Remote Start Mode

To exit the Remote Start mode, follow these steps:

1. Press the Remote Start button on your Key Fob once.
2. The engine will turn off, and the vehicle will be ready for
   operation.

Remote Start Front Defrost Activation — If Equipped

If equipped, the Remote Start Front Defrost Activation feature
automatically activates the front defrost mode when you use the
Remote Start feature. This helps to clear frost or ice from the
windshield.

Remote Start Comfort Systems — If Equipped

If equipped, the Remote Start Comfort Systems feature allows you
to activate certain comfort settings, such as seat heating or
ventilation, using the Remote Start feature. This ensures a
comfortable environment before entering the vehicle.

Remote Start Windshield Wiper De-Icer Activation — If

Equipped

If equipped, the Remote Start Windshield Wiper De-Icer
Activation feature automatically activates the windshield wiper
de-icer when you use the Remote Start feature. This helps to melt
ice or snow from the windshield wipers.

Remote Start Cancel Message — If Equipped

If equipped, the Remote Start Cancel Message feature displays a
message on the instrument cluster to indicate that the Remote Start
has been canceled. This can occur due to certain conditions or user
actions.

Vehicle Security System

If equipped, the Vehicle Security System provides an added layer
of protection against theft. It includes various features to
safeguard your vehicle.

To Arm The System

To arm the Vehicle Security System, follow these steps:

1. Exit the vehicle and close all doors.

2. Press the Lock button on your Key Fob or use the power door
   lock switch.

3. The system will arm, and the vehicle will be secured.

To Disarm The System

To disarm the Vehicle Security System, follow these steps:

1. Unlock the driver’s door using the Key Fob or the key.
2. The system will disarm, and you can enter the vehicle.

Rearming Of The System

The Vehicle Security System will automatically rearm itself
after a certain period of time if no action is taken after
disarming the system. This helps to ensure continuous
protection.

Security System Manual Override

In case of emergencies or system malfunctions, the Vehicle
Security System can be manually overridden. Please refer to the
owner’s manual for detailed instructions on how to perform a manual
override.

Tamper Alert

If someone attempts to tamper with your vehicle while the
Vehicle Security System is armed, a tamper alert will be triggered.
This can include sounding the horn or flashing the lights to
attract attention.

Doors

The 2024 Durango comes with various door locking mechanisms for
convenience and security.

Manual Door Locks

If equipped, the manual door locks can be operated by manually
turning the lock knob on each door. This provides a basic level of
security.

Power Door Locks

If equipped, the power door locks can be operated using the
power door lock switch or the Key Fob. This allows for convenient
locking and unlocking of all doors simultaneously.

Keyless Enter ‘n GoTM – Passive Entry

If equipped, the Keyless Enter ‘n GoTM system allows for passive
entry into the vehicle. As long as you have the Key Fob with you,
the doors will automatically unlock when you approach the
vehicle.

Automatic Unlock On Exit Feature — If Equipped

If equipped, the Automatic Unlock On Exit feature automatically
unlocks all doors when the vehicle is shifted into Park and the
driver’s door is opened. This makes it easier to exit the
vehicle.

Child-Protection Door Lock System — Rear Doors

If equipped, the Child-Protection Door Lock System helps to
prevent accidental opening of the rear doors by children. These
locks can be engaged manually.

Steering Wheel

The steering wheel of the 2024 Durango offers various features
for comfort and adjustability.

Manual Tilt/Telescoping Steering Column — If Equipped

If equipped, the manual tilt/telescoping steering column allows
you to adjust the position of the steering wheel manually. This
helps to find a comfortable driving position.

Power Tilt/Telescoping Steering Column — If Equipped

If equipped, the power tilt/telescoping steering column allows
you to adjust the position of the steering wheel using a power
mechanism. This provides added convenience and ease of
adjustment.

Heated Steering Wheel — If Equipped

If equipped, the heated steering wheel feature allows you to
warm up the steering wheel during cold weather. This provides added
comfort and grip.

FAQ

Q: How do I use the Remote Start feature?

A: To use the Remote Start feature, press the Remote Start
button on your Key Fob twice within five seconds. The vehicle will
start, and the engine will run for a predetermined amount of
time.

Q: How do I disarm the Vehicle Security System?

A: To disarm the Vehicle Security System, unlock the driver’s
door using the Key Fob or the key. The system will disarm, and you
can enter the vehicle.

Q: Can I manually override the Vehicle Security System?

A: Yes, in case of emergencies or system malfunctions, the
Vehicle Security System can be manually overridden. Please refer to
the owner’s manual for detailed instructions on how to perform a
manual override.

OWNER’S MANUAL
2024 DURANGO

ROADSIDE ASSISTANCE
24 HOURS, 7 DAYS A WEEK AT YOUR SERVICE.
CALL 1-800-521-2779 OR VISIT CHRYSLER.RSAHELP.COM (USA) CALL 1-800-363-4869 OR VISIT FCA.ROADSIDEAID.COM (CANADA)
SERVICES: Flat Tire Service, Out Of Gas/Fuel Delivery, Battery Jump Assistance, Lockout Service and Towing Service.
FCA US LLC reserves the right to modify the terms or discontinue the Roadside Assistance Program at any time. The Roadside Assistance Program is subject to restrictions and conditions of use, that are determined solely by FCA US LLC. Please see the Customer Assistance chapter in this Owner’s Manual for further information.

This Owner’s Manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle. FCA US LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured.
With respect to any vehicles sold in Canada, the name FCA US LLC shall be deemed to be deleted and the name FCA Canada Inc. used in substitution therefore.
This Owner’s Manual is intended to familiarize you with the important features of your vehicle. Your most up-to-date Owner’s Manual, Navigation/Uconnect manuals and Warranty Booklet can be found by visiting the website on the back cover.
Vehicle images are for illustration purposes only. Actual products sold may vary.

WARNING: Operating, servicing and maintaining a passenger vehicle or off- highway motor vehicle can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine except as necessary, service your vehicle in a well-ventilated area and wear gloves or wash your hands frequently when servicing your vehicle. For more information go to www.P65Warnings.ca.gov/passenger-vehicle.

TABLE OF CONTENTS
1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1 2 GETTING TO KNOW YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2 3 GETTING TO KNOW YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 3 4 STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 4 5 MULTIMEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 5 6 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 6 7 IN CASE OF EMERGENCY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237 7 8 SERVICING AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253 8 9 TECHNICAL SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301 9 10 CUSTOMER ASSISTANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307 10 11 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312 11

2
INTRODUCTION
SYMBOLS KEY . . . . . . . . . . . . . . . . . . . . . . . 8 ROLLOVER WARNING . . . . . . . . . . . . . . . . . . 8 VEHICLE MODIFICATIONS/ALTERATIONS . . . . . . . 9 SYMBOL GLOSSARY . . . . . . . . . . . . . . . . . . . 9
GETTING TO KNOW YOUR VEHICLE
KEYS . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Key Fob . . . . . . . . . . . . . . . . . . . . . . . 14
SENTRY KEY . . . . . . . . . . . . . . . . . . . . . . . 16 IGNITION SWITCH . . . . . . . . . . . . . . . . . . . . 17
Keyless Enter n GoTM Ignition . . . . . . . . . . . 17 REMOTE START — IF EQUIPPED . . . . . . . . . . . . 18 How To Use Remote Start . . . . . . . . . . . . . 18 To Exit Remote Start Mode . . . . . . . . . . . . 18 Remote Start Front Defrost Activation — If Equipped . . . . . . . . . . . . . . . . . . . . . 19 Remote Start Comfort Systems — If Equipped . 19 Remote Start Windshield Wiper De-Icer Activation — If Equipped . . . . . . . . . . . . . . . . . . . . . 19 Remote Start Cancel Message — If Equipped . . 19 VEHICLE SECURITY SYSTEM — IF EQUIPPED . . . . 20 To Arm The System . . . . . . . . . . . . . . . . 20 To Disarm The System . . . . . . . . . . . . . . . 20 Rearming Of The System . . . . . . . . . . . . . 20 Security System Manual Override . . . . . . . . 20 Tamper Alert . . . . . . . . . . . . . . . . . . . . 20 DOORS . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Manual Door Locks . . . . . . . . . . . . . . . . 20 Power Door Locks . . . . . . . . . . . . . . . . . 21 Keyless Entern GoTM — Passive Entry . . . . . . 21

Automatic Unlock On Exit Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . 23 Child-Protection Door Lock System — Rear Doors . . . . . . . . . . . . . . . . . . . . . 23
STEERING WHEEL . . . . . . . . . . . . . . . . . . . . 24 Manual Tilt/Telescoping Steering Column — If Equipped . . . . . . . . . . . . . . . . . . . . . 24 Power Tilt/Telescoping Steering Column — If Equipped . . . . . . . . . . . . . . . . . . . . . 24 Heated Steering Wheel — If Equipped . . . . . . 25
DRIVER MEMORY SETTINGS — IF EQUIPPED . . . . 25 Programming The Memory Feature . . . . . . . . 25 Linking And Unlinking The Remote Keyless Entry Key Fob To Memory . . . . . . . . . . . . . 26 Memory Position Recall . . . . . . . . . . . . . . 26
SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Manual Adjustment (Front Seats) — If Equipped . . . . . . . . . . . . . . . . . . . . . 26 Manual Adjustment (Rear Seats) . . . . . . . . . 28 Power Adjustment (Front Seats) — If Equipped . 31 Heated Seats — If Equipped . . . . . . . . . . . 32 Front Ventilated Seats — If Equipped . . . . . . 33 Head Restraints . . . . . . . . . . . . . . . . . . 33
UCONNECT VOICE RECOGNITION — IF EQUIPPED . . 35 Introducing Voice Recognition . . . . . . . . . . . 35 Basic Voice Commands . . . . . . . . . . . . . . 35 Get Started . . . . . . . . . . . . . . . . . . . . . 35 Additional Information . . . . . . . . . . . . . . . 36
MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . 36 Inside Rearview Mirror . . . . . . . . . . . . . . . 36 Illuminated Vanity Mirrors . . . . . . . . . . . . . 36 Outside Mirrors . . . . . . . . . . . . . . . . . . . 37

Outside Mirrors With Turn Signal — If Equipped . 37 Outside Automatic Dimming Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . 37 Power Mirrors — If Equipped . . . . . . . . . . . 37 Heated Mirrors — If Equipped . . . . . . . . . . 38
UNIVERSAL GARAGE DOOR OPENER (HomeLink®) — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . 38
Before You Begin Programming HomeLink® . . 38 Erasing All The HomeLink® Channels . . . . . . 38 Identifying Whether You Have A Rolling Code Or Non- Rolling Code Device . . . . . . . . . . . . . . 38 Programming HomeLink® To A Garage Door Opener . . . . . . . . . . . . . . . . . . . . . . . . 39 Programming HomeLink® To A Miscellaneous Device . . . . . . . . . . . . . . . . . . . . . . . . 39 Reprogramming A Single HomeLink® Button . . 39 Canadian/Gate Operator Programming . . . . . 40 Security . . . . . . . . . . . . . . . . . . . . . . . 40 Troubleshooting Tips . . . . . . . . . . . . . . . . 40
EXTERIOR LIGHTS . . . . . . . . . . . . . . . . . . . . 41 Multifunction Lever . . . . . . . . . . . . . . . . . 41 Headlight Switch . . . . . . . . . . . . . . . . . . 41 Daytime Running Lights (DRLs) . . . . . . . . . 42 High/Low Beam Switch . . . . . . . . . . . . . . 42 Automatic High Beam — If Equipped . . . . . . . 42 Flash-To-Pass . . . . . . . . . . . . . . . . . . . . 42 Automatic Headlights . . . . . . . . . . . . . . . 43 Parking Lights And Panel Lights . . . . . . . . . 43 Automatic Headlights With Wipers . . . . . . . . 43 Headlight Delay . . . . . . . . . . . . . . . . . . . 43 Lights-On Reminder . . . . . . . . . . . . . . . . 43 Turn Signals . . . . . . . . . . . . . . . . . . . . . 43 Lane Change Assist — If Equipped . . . . . . . . 43

Automatic Headlight Leveling — If Equipped . . . 43 Battery Saver . . . . . . . . . . . . . . . . . . . . 43
INTERIOR LIGHTS . . . . . . . . . . . . . . . . . . . . 44 Courtesy Lights . . . . . . . . . . . . . . . . . . . 44 Front Map/Reading Lights — If Equipped . . . . 44 Ambient Light — If Equipped . . . . . . . . . . . . 44 Dimmer Control . . . . . . . . . . . . . . . . . . . 45 Illuminated Entry . . . . . . . . . . . . . . . . . . 45
WINDSHIELD WIPERS AND WASHERS . . . . . . . . 45 Windshield Wiper Operation . . . . . . . . . . . 45 Rain Sensing Wipers — If Equipped . . . . . . . 46 Rear Window Wiper/Washer . . . . . . . . . . . 46
CLIMATE CONTROLS . . . . . . . . . . . . . . . . . . 47 Automatic Climate Control Descriptions And Functions . . . . . . . . . . . . . . . . . . . . . . 47 Automatic Temperature Control (ATC) . . . . . . 52 Climate Voice Recognition . . . . . . . . . . . . . 52 Operating Tips . . . . . . . . . . . . . . . . . . . 52
INTERIOR STORAGE AND EQUIPMENT . . . . . . . . 53 Storage . . . . . . . . . . . . . . . . . . . . . . . 53 USB/AUX Control . . . . . . . . . . . . . . . . . . 55 Lighted Cupholders — If Equipped . . . . . . . . 56 Electrical Power Outlets . . . . . . . . . . . . . . 57 Power Inverter — If Equipped . . . . . . . . . . . 58 Wireless Charging Pad — If Equipped . . . . . . 59
WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . 60 Power Windows . . . . . . . . . . . . . . . . . . 60 Wind Buffeting . . . . . . . . . . . . . . . . . . . 61
POWER SUNROOF — IF EQUIPPED . . . . . . . . . . 61 Opening And Closing The Sunroof . . . . . . . . 62 Sunshade Operation . . . . . . . . . . . . . . . . 62 Pinch Protect Feature . . . . . . . . . . . . . . . 62

Sunroof Maintenance . . . . . . . . . . . . . . . 62 Ignition Off Operation . . . . . . . . . . . . . . . 62
HOOD . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Opening The Hood . . . . . . . . . . . . . . . . . 62 Closing The Hood . . . . . . . . . . . . . . . . . . 63
LIFTGATE . . . . . . . . . . . . . . . . . . . . . . . . . 63 Power Liftgate — If Equipped . . . . . . . . . . . 63 Cargo Area Features . . . . . . . . . . . . . . . . 64
ROOF LUGGAGE RACK — IF EQUIPPED . . . . . . . . 65 Deploying The Crossbars . . . . . . . . . . . . . 66 Stowing The Crossbars . . . . . . . . . . . . . . . 67
GETTING TO KNOW YOUR INSTRUMENT PANEL
INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . 69 Instrument Cluster Descriptions . . . . . . . . . 70
SRT INSTRUMENT CLUSTER . . . . . . . . . . . . . . 71 SRT Instrument Cluster Descriptions . . . . . . 72
INSTRUMENT CLUSTER DISPLAY . . . . . . . . . . . 72 Location And Controls . . . . . . . . . . . . . . . 72 Engine Oil Life Reset . . . . . . . . . . . . . . . . 73 Display And Messages . . . . . . . . . . . . . . . 74 Instrument Cluster Display Menu Items . . . . . 75 Battery Saver On/Battery Saver Mode Message — Electrical Load Reduction Actions — If Equipped . . . . . . . . . . . . . . . . . . . . . 77
WARNING LIGHTS AND MESSAGES . . . . . . . . . . 78 Red Warning Lights . . . . . . . . . . . . . . . . . 79 Yellow Warning Lights . . . . . . . . . . . . . . . 81 Yellow Indicator Lights . . . . . . . . . . . . . . . 83 Green Indicator Lights . . . . . . . . . . . . . . . 84

3
White Indicator Lights . . . . . . . . . . . . . . . 85 Blue Indicator Lights . . . . . . . . . . . . . . . . 85
ONBOARD DIAGNOSTIC SYSTEM — OBD II . . . . . . 85 Onboard Diagnostic System (OBD II) Cybersecurity . . . . . . . . . . . . . . . . . . . . 86
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . 86
STARTING AND OPERATING
STARTING THE ENGINE . . . . . . . . . . . . . . . . . 87 Automatic Transmission . . . . . . . . . . . . . . 87 Normal Starting . . . . . . . . . . . . . . . . . . 87 AutoPark . . . . . . . . . . . . . . . . . . . . . . 88 Extended Park Starting . . . . . . . . . . . . . . 89 If Engine Fails To Start . . . . . . . . . . . . . . 89 Cold Weather Operation (Below ­22°F Or -30°C) . . . . . . . . . . . . . 89 After Starting . . . . . . . . . . . . . . . . . . . . 89
ENGINE BREAK-IN RECOMMENDATIONS — NON-SRT . . . . . . . . . . . . . . . . . . . . . . . . . 89 ENGINE BREAK-IN RECOMMENDATIONS ­ SRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 PARKING BRAKE . . . . . . . . . . . . . . . . . . . . 90 AUTOMATIC TRANSMISSION . . . . . . . . . . . . . . 91
Ignition Park Interlock . . . . . . . . . . . . . . . 92 Brake Transmission Shift Interlock (BTSI) System . . . . . . . . . . . . . . . . . . . 92 Fuel Economy (ECO) Mode . . . . . . . . . . . . 92 8-Speed Automatic Transmission . . . . . . . . 92
SPORT MODE — IF EQUIPPED . . . . . . . . . . . . . 95 ALL-WHEEL DRIVE OPERATION . . . . . . . . . . . . 95
Single-Speed Operating Instructions/Precautions — If Equipped . . . . . . . . . . . . . . . . . . . . . 95

4
Electronically Shifted Transfer Case — If Equipped . . . . . . . . . . . . . . . . . . . . . 96 Shifting Procedure . . . . . . . . . . . . . . . . . 97
TOW N GO — IF EQUIPPED . . . . . . . . . . . . . . . 97 Guidelines For Track Use . . . . . . . . . . . . . 98
SELEC-TRACK — IF EQUIPPED . . . . . . . . . . . . . 99 Custom . . . . . . . . . . . . . . . . . . . . . . . 100 Active Damping System . . . . . . . . . . . . . 100 Launch Control . . . . . . . . . . . . . . . . . . 100 Torque Reserve — If Equipped . . . . . . . . . . 101
FUEL SAVER TECHNOLOGY 5.7L AND 6.4L ONLY — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . 102 POWER STEERING . . . . . . . . . . . . . . . . . . 102 STOP/START SYSTEM — IF EQUIPPED. . . . . . . . 102
Autostop Mode . . . . . . . . . . . . . . . . . . 102 Possible Reasons The Engine Does Not Autostop . . . . . . . . . . . . . . . . . . . . . . 102 To Start The Engine While In Autostop Mode . 103 To Manually Turn Off The Stop/Start System . 103 To Manually Turn On The Stop/Start System . . 103 System Malfunction . . . . . . . . . . . . . . . . 103
CRUISE CONTROL SYSTEMS — IF EQUIPPED . . . . 103 Cruise Control . . . . . . . . . . . . . . . . . . . 104 Adaptive Cruise Control (ACC) . . . . . . . . . . 105
PARKSENSE FRONT/REAR PARK ASSIST SYSTEM — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . 111
ParkSense Sensors . . . . . . . . . . . . . . . . 112 ParkSense Display . . . . . . . . . . . . . . . . 112 ParkSense Warning Display . . . . . . . . . . . 115 Enabling And Disabling ParkSense . . . . . . . 115 Operation With A Trailer . . . . . . . . . . . . . 115 Service The ParkSense Park Assist System . . 116

Cleaning The ParkSense System . . . . . . . . 116 ParkSense System Usage Precautions . . . . . 116
LANESENSE — IF EQUIPPED . . . . . . . . . . . . . 117 LaneSense Operation . . . . . . . . . . . . . . . 117 Turning LaneSense On Or Off . . . . . . . . . . 117 LaneSense Warning Message . . . . . . . . . . 117 Changing LaneSense Status . . . . . . . . . . . 119
PARKVIEW REAR BACK UP CAMERA . . . . . . . . 119
REFUELING THE VEHICLE . . . . . . . . . . . . . . . 120
VEHICLE LOADING . . . . . . . . . . . . . . . . . . . 120 Certification Label . . . . . . . . . . . . . . . . 120
TRAILER TOWING . . . . . . . . . . . . . . . . . . . 121 Common Towing Definitions . . . . . . . . . . . 121 Trailer Hitch Classification . . . . . . . . . . . . 123 Trailer Towing Weights (Maximum Trailer Weight Ratings) — Non- SRT . . . . . . . . . . . . . . . . . . . . . . 124 Trailer Hitch Receiver Cover Removal — If Equipped . . . . . . . . . . . . . . . . . . . . . 124 Trailer And Tongue Weight . . . . . . . . . . . . 125 Towing Requirements . . . . . . . . . . . . . . 125 Towing Tips . . . . . . . . . . . . . . . . . . . . 129
RECREATIONAL TOWING (BEHIND MOTORHOME) . . . . . . . . . . . . . . . 130
Towing This Vehicle Behind Another Vehicle . 130 Recreational Towing — Rear- Wheel Drive Models . . . . . . . . . . . . . . . . . . . . . . . 130 Recreational Towing — All-Wheel Drive Models (Single-Speed Transfer Case) . . . . . . . . . . 130 Recreational Towing — All-Wheel Drive Models (Two-Speed Transfer Case) . . . . . . . . . . . . 131

DRIVING TIPS. . . . . . . . . . . . . . . . . . . . . . 133 On-Road Driving Tips . . . . . . . . . . . . . . . 133 Off-Road Driving Tips . . . . . . . . . . . . . . . 133
MULTIMEDIA
UCONNECT SYSTEMS . . . . . . . . . . . . . . . . . 135 CYBERSECURITY . . . . . . . . . . . . . . . . . . . 135 UCONNECT SETTINGS . . . . . . . . . . . . . . . . . 135
Customer Programmable Features . . . . . . . 136
UCONNECT INTRODUCTION . . . . . . . . . . . . . . 152 System Overview . . . . . . . . . . . . . . . . . 152 Safety And General Information . . . . . . . . . 153
UCONNECT MODES . . . . . . . . . . . . . . . . . . 154 Steering Wheel Audio Controls . . . . . . . . . 154 Radio Mode . . . . . . . . . . . . . . . . . . . . 154 Media Mode . . . . . . . . . . . . . . . . . . . . 158 Phone Mode . . . . . . . . . . . . . . . . . . . . 159
CONNECTED VEHICLE SERVICES — IF EQUIPPED . 166 Is My Vehicle Connected? . . . . . . . . . . . . 166 Introduction To Connected Vehicle Services . . 166 Getting Started With Connected Vehicle Services . . . . . . . . . . . . . . . . . . . . . . 167 Using Brand Connect . . . . . . . . . . . . . . . 168 Manage My Brand Connect Account . . . . . . 176
CONNECTED SERVICES FAQs . . . . . . . . . . . . 176 Connected Services SOS FAQs — If Equipped . 176 Connected Services Remote Door Lock/Unlock FAQs . . . . . . . . . . . . . . . . . . . . . . . . 176 Connected Services Roadside Assistance FAQs . . . . . . . . . . . . . . . . . . . . . . . . 177 Connected Services Send & Go FAQs — If Equipped . . . . . . . . . . . . . . . . . . . . . 177

Connected Services Vehicle Finder FAQs . . . . 177 Connected Services Stolen Vehicle Assistance FAQs — If Equipped . . . . . . . . . . . . . . . . 177 Connected Services Remote Vehicle Start FAQs . . . . . . . . . . . . . . . . . . . . . . . . 178 Connected Services Remote Horn & Lights FAQs . . . . . . . . . . . . . . . . . . . . . . . . 178 Connected Services Account FAQs — If Equipped . . . . . . . . . . . . . . . . . . . . . 178 Data Collection & Privacy . . . . . . . . . . . . 179
PERFORMANCE PAGES . . . . . . . . . . . . . . . . 180 Timers . . . . . . . . . . . . . . . . . . . . . . . 180 Gauges . . . . . . . . . . . . . . . . . . . . . . . 181 Dynamometer (Dyno)/Engine . . . . . . . . . . 182 G-Force . . . . . . . . . . . . . . . . . . . . . . . 183 Vehicle Dynamics . . . . . . . . . . . . . . . . . 184
SRT DRIVE MODES — IF EQUIPPED . . . . . . . . . 184 Sport Mode . . . . . . . . . . . . . . . . . . . . 184 Track Mode . . . . . . . . . . . . . . . . . . . . 184 Tow Mode . . . . . . . . . . . . . . . . . . . . . 185 Snow Mode . . . . . . . . . . . . . . . . . . . . 185 Auto Mode . . . . . . . . . . . . . . . . . . . . . 186 Custom Mode . . . . . . . . . . . . . . . . . . . 186
RACE OPTIONS . . . . . . . . . . . . . . . . . . . . . 188 Launch Control . . . . . . . . . . . . . . . . . . 189 Shift Light . . . . . . . . . . . . . . . . . . . . . 190
GUIDELINES FOR TRACK USE . . . . . . . . . . . . 190
ECO MODE . . . . . . . . . . . . . . . . . . . . . . . 191
RADIO OPERATION AND MOBILE PHONES . . . . . 192 Regulatory And Safety Information . . . . . . . 192

SAFETY
SAFETY FEATURES. . . . . . . . . . . . . . . . . . . 193 Anti-Lock Brake System (ABS) . . . . . . . . . 193 Rear Seat Reminder Alert (RSRA) . . . . . . . 193 Electronic Brake Control (EBC) System . . . . 194
AUXILIARY DRIVING SYSTEMS . . . . . . . . . . . . 198 Blind Spot Monitoring (BSM) — If Equipped . . 198 Forward Collision Warning (FCW) With Mitigation . . . . . . . . . . . . . . . . . . 202 Tire Pressure Monitoring System (TPMS) . . . 204
OCCUPANT RESTRAINT SYSTEMS . . . . . . . . . . 207 Occupant Restraint Systems Features . . . . . 207 Important Safety Precautions . . . . . . . . . . 207 Seat Belt Systems . . . . . . . . . . . . . . . . 208 Supplemental Restraint Systems (SRS) . . . . 213 Child Restraints . . . . . . . . . . . . . . . . . 222
SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . 233 Transporting Passengers . . . . . . . . . . . . . 233 Transporting Pets . . . . . . . . . . . . . . . . 233 Connected Vehicles . . . . . . . . . . . . . . . . 234 Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . 234 Periodic Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . 235 Exhaust Gas . . . . . . . . . . . . . . . . . . . 235 Carbon Monoxide Warnings . . . . . . . . . . . 236
IN CASE OF EMERGENCY
HAZARD WARNING FLASHERS . . . . . . . . . . . 237 SOS AND ASSIST MIRROR — IF EQUIPPED . . . . . 237 JACKING AND TIRE CHANGING — IF EQUIPPED . . 239
Preparations For Jacking . . . . . . . . . . . . 240

5
Run Flat Tires — If Equipped . . . . . . . . . . . 240 Jack Location — If Equipped . . . . . . . . . . . 240 Spare Tire Stowage — If Equipped . . . . . . . 241 Spare Tire Removal — If Equipped . . . . . . . . 241 Jacking Instructions — If Equipped . . . . . . . 242
JUMP STARTING . . . . . . . . . . . . . . . . . . . . 245 Preparations For Jump Start . . . . . . . . . . . 246 Jump Starting Procedure . . . . . . . . . . . . . 246
REFUELING IN EMERGENCY ­ IF EQUIPPED . . . . 247 IF YOUR ENGINE OVERHEATS. . . . . . . . . . . . . 248 MANUAL PARK RELEASE . . . . . . . . . . . . . . . 249 FREEING A STUCK VEHICLE . . . . . . . . . . . . . 250 TOWING A DISABLED VEHICLE . . . . . . . . . . . 251
Rear-Wheel Drive Models . . . . . . . . . . . . 251 All-Wheel Drive Models . . . . . . . . . . . . . . 252
TOWING A DISABLED SRT VEHICLE . . . . . . . . . 252 ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) . . . . . . . . . . . . . . . . . . . . . . . . . 252 EVENT DATA RECORDER (EDR) . . . . . . . . . . . 252
SERVICING AND MAINTENANCE
SCHEDULED SERVICING . . . . . . . . . . . . . . . 253 Maintenance Plan . . . . . . . . . . . . . . . . 253
SCHEDULED SERVICING — SRT . . . . . . . . . . . 255 Maintenance Plan — SRT . . . . . . . . . . . . 256
ENGINE COMPARTMENT . . . . . . . . . . . . . . . 259 3.6L Engine . . . . . . . . . . . . . . . . . . . . 259 5.7L Engine . . . . . . . . . . . . . . . . . . . . 260 6.2L Supercharged Engine . . . . . . . . . . . 261 6.4L Engine . . . . . . . . . . . . . . . . . . . . 262 Checking Oil Level . . . . . . . . . . . . . . . . 263 Adding Washer Fluid . . . . . . . . . . . . . . . 263

6
Maintenance-Free Battery . . . . . . . . . . . . 263 Pressure Washing . . . . . . . . . . . . . . . . . 264
VEHICLE MAINTENANCE . . . . . . . . . . . . . . . 264 Engine Oil . . . . . . . . . . . . . . . . . . . . . 264 Engine Oil Filter . . . . . . . . . . . . . . . . . . 265 Engine Air Cleaner Filter . . . . . . . . . . . . . 265 Air Conditioner Maintenance . . . . . . . . . . 266 Accessory Drive Belt Inspection . . . . . . . . . 268 Body Lubrication . . . . . . . . . . . . . . . . . 269 Windshield Wiper Blades . . . . . . . . . . . . 269 Exhaust System . . . . . . . . . . . . . . . . . . 271 Cooling System . . . . . . . . . . . . . . . . . . 272 Brake System . . . . . . . . . . . . . . . . . . . 274 Automatic Transmission . . . . . . . . . . . . . 275 Front/Rear Axle Fluid . . . . . . . . . . . . . . 275 Transfer Case . . . . . . . . . . . . . . . . . . . 276 Fuses . . . . . . . . . . . . . . . . . . . . . . . 276 Bulb Replacement . . . . . . . . . . . . . . . . 282
TIRES . . . . . . . . . . . . . . . . . . . . . . . . . . 284 Tire Safety Information . . . . . . . . . . . . . 284 Tires — General Information . . . . . . . . . . . 290 Tire Types . . . . . . . . . . . . . . . . . . . . . 292 Spare Tires — If Equipped . . . . . . . . . . . . 293 Wheel And Wheel Trim Care . . . . . . . . . . . 294 Snow Traction Devices . . . . . . . . . . . . . . 295 Tire Rotation Recommendations . . . . . . . . 296
DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . . . . . . . . . 297
Treadwear . . . . . . . . . . . . . . . . . . . . . 297 Traction Grades . . . . . . . . . . . . . . . . . . 297 Temperature Grades . . . . . . . . . . . . . . . 297
STORING THE VEHICLE . . . . . . . . . . . . . . . . 298 Battery Storage Mode . . . . . . . . . . . . . . 298

BODYWORK. . . . . . . . . . . . . . . . . . . . . . . 298 Protection From Atmospheric Agents . . . . . 298 Body And Underbody Maintenance . . . . . . . 298 Preserving The Bodywork . . . . . . . . . . . . 299
INTERIORS . . . . . . . . . . . . . . . . . . . . . . . 299 Seats And Fabric Parts . . . . . . . . . . . . . . 299 Plastic And Coated Parts . . . . . . . . . . . . . 299 Leather Surfaces . . . . . . . . . . . . . . . . . 300 Glass Surfaces . . . . . . . . . . . . . . . . . . 300
TECHNICAL SPECIFICATIONS
VEHICLE IDENTIFICATION NUMBER (VIN) . . . . . . 301 BRAKE SYSTEM . . . . . . . . . . . . . . . . . . . . 301 WHEEL AND TIRE TORQUE SPECIFICATIONS . . . . 301
Torque Specifications . . . . . . . . . . . . . . . 301
FUEL REQUIREMENTS . . . . . . . . . . . . . . . . 302 3.6L Engine . . . . . . . . . . . . . . . . . . . . 302 5.7L Engine . . . . . . . . . . . . . . . . . . . . 302 6.2L Supercharged And 6.4L Engine . . . . . . 302 Reformulated Gasoline . . . . . . . . . . . . . 302 Materials Added To Fuel . . . . . . . . . . . . . 302 Gasoline/Oxygenate Blends . . . . . . . . . . 302 Do Not Use E-85 In Non-Flex Fuel Vehicles . . 303 CNG And LP Fuel System Modifications . . . . 303 Methylcyclopentadienyl Manganese Tricarbonyl (MMT) In Gasoline . . . . . . . . . . . . . . . . 303 Fuel System Cautions . . . . . . . . . . . . . . 303
FLUID CAPACITIES . . . . . . . . . . . . . . . . . . . 304 FLUID CAPACITIES — SRT . . . . . . . . . . . . . . . 304 ENGINE FLUIDS AND LUBRICANTS . . . . . . . . . 305 CHASSIS FLUIDS AND LUBRICANTS . . . . . . . . 305

ENGINE FLUIDS AND LUBRICANTS — SRT . . . . . 306 CHASSIS FLUIDS AND LUBRICANTS — SRT . . . . 306
CUSTOMER ASSISTANCE
SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . 307
Prepare For The Appointment . . . . . . . . . . 307 Prepare A List . . . . . . . . . . . . . . . . . . . 307 Be Reasonable With Requests . . . . . . . . . 307
IF YOU NEED ASSISTANCE . . . . . . . . . . . . . . 307 Roadside Assistance . . . . . . . . . . . . . . . 307 FCA US LLC Customer Center . . . . . . . . . . 308 FCA Canada Customer Care . . . . . . . . . . . 308 Mexico . . . . . . . . . . . . . . . . . . . . . . . 308 Puerto Rico And US Virgin Islands . . . . . . . 308 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . . . . 308 Service Contract . . . . . . . . . . . . . . . . . 308
WARRANTY INFORMATION . . . . . . . . . . . . . . 309 MOPAR® PARTS . . . . . . . . . . . . . . . . . . . 309 REPORTING SAFETY DEFECTS . . . . . . . . . . . . 309
In The 50 United States And Washington, D.C. . . . . . . . . . . . . . . . . . 309 In Canada . . . . . . . . . . . . . . . . . . . . . 310
Ordering and Accessing Additional Owner’s Information . . . . . . . . . . . . . . . . . . . . . . 310 Change Of Ownership Or Address . . . . . . . . . . 310 General Information . . . . . . . . . . . . . . . . . . 310

7
INTRODUCTION 1
Dear Customer,
Congratulations on the purchase of your new Dodge vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality.
This is a specialized utility vehicle. It can go places and perform tasks that are not intended for conventional passenger vehicles. It handles and maneuvers differently from many passenger vehicles both on-road and off-road, so take time to become familiar with your vehicle. If equipped, the two-wheel drive version of this vehicle was designed for on-road use only. It is not intended for off-road driving or use in other severe conditions suited for a four-wheel drive vehicle. Before you start to drive this vehicle, read the Owner’s Manual. Be sure you are familiar with all vehicle controls, particularly those used for braking, steering, transmission, and transfer case shifting. Learn how your vehicle handles on different road surfaces. Your driving skills will improve with experience. When driving off-road, or working the vehicle, don’t overload the vehicle or expect the vehicle to overcome the natural laws of physics. Always observe federal, state, provincial and local laws wherever you drive. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or a collision page 133.
This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by customer-oriented documents. Within this information, you will find a description of the services that FCA US LLC offers to its customers as well as the details of the terms and conditions for maintaining its validity. Please take the time to read all of these publications carefully before driving your vehicle for the first time. Following the instructions, recommendations, tips, and important warnings in this manual will help ensure safe and enjoyable operation of your vehicle.
This Owner’s Manual describes all versions of this vehicle. Options and equipment dedicated to specific markets or versions are not expressly indicated in the text. Therefore, you should only consider the information that is related to the trim level, engine, and version that you have purchased. Any content introduced throughout the Owner’s Information, which may or may not be applicable to your vehicle, will be identified with the wording “If Equipped”. All data contained in this publication are intended to help you use your vehicle in the best possible way. FCA US LLC aims at a constant improvement of the vehicles produced. For this reason, it reserves the right to make changes to the model described for technical and/or commercial reasons. For further information, contact an authorized dealer.
When it comes to service remember that authorized dealers know your Dodge best, have factory-trained technicians, genuine Mopar® parts, and care about your satisfaction.

8 INTRODUCTION
SYMBOLS KEY
WARNING! CAUTION! NOTE: TIP: PAGE REFERENCE ARROW

These statements apply to operating procedures that could result in a collision, bodily injury and/or death.
These statements apply to procedures that could result in damage to your vehicle.
A suggestion which will improve installation, operation, and reliability. If not followed, may result in damage.
General ideas/solutions/suggestions on easier use of the product or functionality.
Follow this reference for additional information on a particular feature.

ROLLOVER WARNING
Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles. It is capable of performing better in a wide variety of off-road applications. Driven in an unsafe manner, all vehicles can go out of control. Because of the higher center of gravity, if this vehicle is out of control, it may roll over while some other vehicles may not.
Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully.

FOOTNOTE

Supplementary and relevant information pertaining to the topic.

Rollover Warning Label

If you do not read the entire Owner’s Manual, you may miss important information. Observe all Cautions and Warnings.

Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the US government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up.

VEHICLE MODIFICATIONS/ALTERATIONS
WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
SYMBOL GLOSSARY
Some car components have colored labels with symbols indicating precautions to be observed when using this component. It is important to follow all warnings when operating your vehicle. See the following for the definition of each symbol page 78. NOTE: Warning and Indicator lights are different based upon equipment options and current vehicle status. Some telltales are optional and may not appear.
Red Warning Lights
Seat Belt Reminder Warning Light page 79
Air Bag Warning Light page 79
Brake Warning Light page 79

INTRODUCTION 9 Red Warning Lights
1
Battery Charge Warning Light page 79
Door Open Warning Light page 79
Electric Power Steering (EPS) Fault Warning Light page 80
Electronic Throttle Control (ETC) Warning Light page 80
Engine Coolant Temperature Warning Light page 80
Hood Open Warning Light page 80

10 INTRODUCTION

Red Warning Lights
Liftgate Open Warning Light page 80

Oil Pressure Warning Light page 80

Oil Temperature Warning Light page 80

Trailer Brake Disconnected Warning Light page 80

Transmission Temperature Warning Light page 81

Vehicle Security Warning Light page 81

Yellow Warning Lights Engine Check/Malfunction Indicator Warning Light (MIL)
page 82
Electronic Stability Control (ESC) Active Warning Light page 81
Electronic Stability Control (ESC) OFF Warning Light page 81
Low Washer Fluid Warning Light page 82
Tire Pressure Monitoring System (TPMS) Warning Light page 82
Low Fuel Warning Light page 82

Yellow Warning Lights Anti-Lock Brake System (ABS) Warning Light
page 81
Service Forward Collision Warning (FCW) Light page 82
Service Adaptive Cruise Control (ACC) Warning Light page 82
Service AWD Warning Light page 82
Service Stop/Start System Warning Light page 82
LaneSense Warning Light page 81

INTRODUCTION 11 Yellow Warning Lights
1
Service LaneSense Warning Light page 81
Cruise Control Fault Warning Light page 82
Yellow Indicator Lights
Forward Collision Warning (FCW) OFF Indicator Light page 83
All Wheel Drive (AWD) Low Indicator Light page 83
NEUTRAL Indicator Light page 83
Trailer Merge Assist Indicator Light page 83

12 INTRODUCTION Green Indicator Lights
Adaptive Cruise Control (ACC) Set With Target Indicator Light page 84
Adaptive Cruise Control (ACC) Set Without Target Indicator Light page 84
ECO Mode Indicator Light page 84
Cruise Control Set Indicator Light page 84
LaneSense Indicator Light page 84
Parking/Headlights On Indicator Light page 84

Green Indicator Lights Snow Mode Indicator Light page 84
Sport Mode Indicator Light page 84
Sport Mode Indicator Light page 84
Stop/Start Active Indicator Light page 84
Tow Mode Indicator Light page 84
Track Mode Indicator Light page 84

Green Indicator Lights Turn Signal Indicator Lights page 84
White Indicator Lights Adaptive Cruise Control (ACC) Ready Indicator Light
page 85
Custom Mode SRT Indicator Light page 85
Cruise Control Ready Indicator Light page 85
Speed Warning Indicator Light page 85
LaneSense Indicator Light page 85

INTRODUCTION 13
White Indicator Lights
1
Valet Mode SRT Indicator Light page 85
Blue Indicator Lights
High Beam Indicator Light page 85

14
GETTING TO KNOW YOUR VEHICLE

KEYS
KEY FOB
Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter `n GoTM (if equipped), Remote Start (if equipped), and remote power liftgate operation. The key fob allows you to lock or unlock the doors and liftgate from distances up to approximately 66 ft (20 m). The key fob does not need to be pointed at the vehicle to activate the system. The key fob also contains an emergency key, which is stored in the rear of the key fob.
NOTE:
· The key fob’s wireless signal may be blocked if the key fob is located next to a mobile phone, laptop, or other electronic device. This may result in poor performance.
· With ignition in the ON position and the vehicle moving at 2 mph (4 km/h), all RKE commands are disabled.
NOTE: For SRT Models:
· SRT vehicles equipped with the 6.2L engine come with two red key fobs, that allow for different engine power levels page 184.
· Only 6.2L engine vehicles can come equipped with red key fobs.

Key Fob
1 — Unlock 2 — Liftgate 3 — Emergency Key 4 — Lock 5 — Remote Start 6 — Panic
In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery. A low key fob battery can be verified by referring to the instrument cluster, which will display directions to follow page 310.

To Lock/Unlock The Doors And Liftgate
Push and release the unlock button on the key fob once to unlock the driver’s door, or twice within five seconds to unlock all the doors and the liftgate. To lock all the doors and the liftgate, push the lock button once.
When the doors are unlocked, the turn signals will flash and the illuminated entry system will be activated. When the doors are locked, the turn signals will flash and the horn will chirp.
NOTE:
· If the vehicle is unlocked with the key fob, and no door is opened within 60 seconds, the vehicle will relock and the security system will arm (if equipped).
· If one or more doors are open, or the liftgate is open, the doors will lock. The doors will unlock again automatically if the key fob is left inside the passenger compartment, otherwise the doors will stay locked.
All doors can be programmed to unlock on the first push of the unlock button within Uconnect Settings
page 135.
Key Left Vehicle Feature
If a valid key fob is no longer detected inside the vehicle while the vehicle’s ignition system is in the ON/RUN or START position, the message “Key Fob Has Left The Vehicle” will be shown in the instrument cluster display along with an interior chime. An exterior audible and visual alert will also be activated to warn the driver.

The vehicle’s horn will rapidly chirp three times along with a single flash of the vehicle’s exterior lights.
NOTE:
· The doors have to be open and then closed in order for the vehicle to detect a key fob. The Key Left Vehicle feature will activate when the first door is closed and no key fob is detected in the vehicle. If the warning has been activated, and the other doors are closed, no other warnings will be issued.
· These alerts will not be activated in situations where the vehicle’s engine is left running with the key fob inside, or the key fob’s wireless signals are blocked.
Replacing The Battery In The Key Fob
The recommended replacement battery is one CR2032 battery.
NOTE:
· Customers are recommended to use a battery obtained from Mopar®. Aftermarket coin battery dimensions may not meet the original OEM coin battery dimensions.
· Perchlorate material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate for further information.
· Do not touch the battery terminals that are on the back housing or the printed circuit board.
1. Remove the emergency key (2) by sliding the emergency key release (1) on the back of the key fob and pulling the emergency key out with your other hand.

Emergency Key Removal 1 — Emergency Key Release 2 — Emergency Key 2. Separate the key fob halves using a flat-blade
screwdriver or a coin, and gently pry the two halves of the key fob apart. Make sure not to damage the seal during removal.
Emergency Key Removal

GETTING TO KNOW YOUR VEHICLE 15
2
Separating Case With A Coin
Key Fob Battery Replacement 3. Remove the back cover to access and replace the
battery. When replacing the battery, match the (+) sign on the battery to the (+) sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol.

16 GETTING TO KNOW YOUR VEHICLE
4. To assemble the key fob case, snap the two halves together.
WARNING!
· The integrated key fob contains a coin cell battery. Do not ingest the battery; there is a chemical burn hazard. If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.
· If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.
· Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.
Programming And Requesting Additional Key Fobs
Programming the key fob may be performed by an authorized dealer.
NOTE:
· Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle.
· Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.

WARNING!
· Always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unattended.
· For vehicles equipped with Keyless Enter `n GoTM Ignition, always remember to place the ignition in the OFF position when exiting the vehicle.
Duplication of key fobs may be performed at an authorized dealer. This procedure consists of programming a blank key fob to the vehicle electronics. A blank key fob is one that has never been programmed.
NOTE:
· When having the Sentry Key Immobilizer system serviced, bring all vehicle keys with you to an authorized dealer.
· Emergency keys must be ordered to the correct key cut to match the vehicle locks.
· It is not mandatory to replace the key fob if a new emergency key is needed, and vice versa.
NOTE: For SRT Models: Vehicles equipped with the 6.2L and 6.4L engines, black key fobs must be replaced with black key fobs and red key fobs must be replaced with red key fobs
SENTRY KEY
The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.

The system uses a key fob, keyless push button ignition and a Radio Frequency (RF) receiver to prevent unauthorized vehicle operation. Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle. The system will shut the engine off in two seconds if an invalid key fob is used to start the engine.
After placing the ignition switch in the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone used an invalid key fob to start the engine. Either of these conditions will result in the engine being shut off after two seconds.
If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.
CAUTION!
The Sentry Key Immobilizer system is not compatible with some aftermarket Remote Start systems. Use of these systems may result in vehicle starting problems and loss of security protection.
All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics
page 310.
NOTE: A key fob that has not been programmed is also considered an invalid key.

IGNITION SWITCH
KEYLESS ENTER `N GOTM IGNITION
This feature allows the driver to operate the ignition switch with the push of a button as long as the key fob is in the passenger compartment. The START/STOP ignition button has several operating modes that are labeled and will illuminate when in position. These modes are OFF, ACC, ON/RUN, and START.
Keyless Push Button Ignition 1 — OFF 2 — ACC 3 — ON/RUN The push button ignition can be placed in the following modes: OFF
· The engine is stopped · Some electrical devices (e.g. power locks, alarm,
etc.) are still available

ACC
· Engine is not started · Some electrical devices are available (e.g. power
windows, etc.) ON/RUN
· Driving position · All electrical devices are available (e.g. climate con-
trols, etc.) START
· The engine will start (when foot is on the brake pedal) NOTE: If the ignition position does not change with a push of the ignition button, and the instrument cluster display message “Key Fob Not Detected” is being displayed, the key fob may have a low or depleted battery. In this situation, a backup method can be used to operate the ignition switch. Put the nose side of the key fob (side opposite of the emergency key) against the START/ STOP ignition button and push to operate the ignition switch.
Depleted Key Fob Battery Procedure

GETTING TO KNOW YOUR VEHICLE 17

WARNING!

· Before exiting a vehicle, always shift the automatic

transmission into PARK and apply the parking

brake. Always make sure the keyless ignition is in

the OFF position, remove the key fob from the

2

vehicle and lock the vehicle.

· Never leave children alone in a vehicle, or with

access to an unlocked vehicle.

· Allowing children to be in a vehicle unattended is

dangerous for a number of reasons. A child or oth-

ers could be seriously or fatally injured. Children

should be warned not to touch the parking brake,

brake pedal or the gear selector.

· Do not leave the key fob in or near the vehicle, or

in a location accessible to children, and do not

leave the ignition of a vehicle equipped with Key-

less Enter `n GoTM in the ACC or ON/RUN position.

A child could operate power windows, other con-

trols, or move the vehicle.

· Do not leave children or animals inside parked

vehicles in hot weather. Interior heat buildup may

cause serious injury or death.

CAUTION! An unlocked vehicle is an invitation for thieves. Always remove the key fobs from vehicle, place the ignition in the OFF position and lock all doors when leaving the vehicle unattended.
NOTE:
· For more information on normal starting procedures, see page 87.

18 GETTING TO KNOW YOUR VEHICLE
· When opening the driver’s door with the ignition in ON/RUN (engine not running), a chime will sound to remind you to place the ignition in the OFF position. In addition to the chime, the message will display “Ignition Or Accessory On” in the cluster.
REMOTE START — IF EQUIPPED
This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security. The system has a range of 328 ft (100 m). Remote Start is used to defrost windows in cold weather, and to reach a comfortable climate in all ambient conditions before the customer enters the vehicle.
NOTE: Obstructions between the vehicle and key fob may reduce this range page 310.
WARNING!
· Do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon monoxide which is odorless and colorless. Carbon monoxide is poisonous and can cause serious injury or death when inhaled.
· Keep key fobs away from children. Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.

HOW TO USE REMOTE START
Push and release the Remote Start button on the key fob twice within five seconds. The vehicle doors will lock, the parking lights will flash, and the horn will chirp twice (if programmed). Then, the engine will start, and the vehicle will remain in the Remote Start mode for a 15 minute cycle. Pushing the Remote Start button a third time shuts the engine off.
To drive the vehicle, push the unlock button, and with a valid Keyless Enter `n GoTM key fob in the vehicle, place the ignition in the ON/RUN position.
NOTE:
· With Remote Start, the engine will only run for 15 minutes.
· Remote Start can only be used twice. · If an engine fault is present or fuel level is low, the
vehicle will start and then shut down in 10 seconds.
· The parking lights will turn on and remain on during Remote Start mode.
· For security, power window and sunroof (if equipped) operation is disabled when the vehicle is in the Remote Start mode.
· The ignition must be placed in the ON/RUN position before the Remote Start sequence can be repeated for a third cycle.
All of the following conditions must be met before the engine will remote start:
· Gear selector in PARK · Doors closed · Hood closed · Liftgate closed

· Hazard switch off · Brake pedal not pressed · Battery at an acceptable charge level · Panic button not pressed · System not disabled from previous Remote Start
event
· Vehicle Security system indicator flashing · Ignition in OFF position · Fuel level meets minimum requirement · Vehicle Security system is not signaling an intrusion · Malfunction Indicator Light (MIL) is not illuminated
WARNING!
· Do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon monoxide which is odorless and colorless. Carbon monoxide is poisonous and can cause serious injury or death when inhaled.
· Keep key fobs away from children. Operation of the Remote Start system, windows, door locks or other controls could cause serious injury or death.
TO EXIT REMOTE START MODE
To drive the vehicle after starting the Remote Start system, either push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter `n GoTM — Passive Entry via the door handles, and disarm the Vehicle Security system (if equipped). Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.

The Remote Start system will turn the engine off if the Remote Start button on the key fob is pushed again, or if the engine is allowed to run for the entire 15 minute cycle. Once the ignition is placed in the ON/RUN position, the climate controls will resume the previously set operations (temperature, blower control, etc.).
NOTE:
· To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid Remote Start request.
· For vehicles equipped with the Keyless Enter `n GoTM — Passive Entry feature, the message “Remote Start Active — Push Start Button” will display in the instrument cluster display until you push the START/STOP ignition button.
REMOTE START FRONT DEFROST ACTIVATION — IF EQUIPPED
When Remote Start is active, and the outside ambient temperature is 40°F (4.5°C) or below, the system will automatically activate front defrost for 15 minutes or less. The timing is dependent on the ambient temperature. Once the timer expires, the system will automatically adjust the settings depending on ambient conditions. See “Remote Start Comfort Systems — If Equipped” in the next section for detailed operation.

REMOTE START COMFORT SYSTEMS — IF EQUIPPED
When Remote Start is activated, the front and rear defrost will automatically turn on in cold weather. The heated steering wheel and driver heated seat feature will turn on if selected in the Comfort menu screen within Uconnect Settings page 135. In warm weather, the driver vented seat feature will automatically turn on when Remote Start is activated, if programmed in the Comfort menu screen. The vehicle will adjust the climate control settings depending on the outside ambient temperature.
Automatic Temperature Control (ATC) — If Equipped
The climate controls will automatically adjust to the optimal temperature and mode settings depending on the outside ambient temperature. This will occur until the ignition is placed in the ON/RUN position, where the climate controls will resume their previous settings.
Manual Temperature Control (MTC) — If Equipped
· In ambient temperatures at 40°F (4.5°C) or below, the climate settings will default to maximum heat, with fresh air entering the cabin. If the front defrost timer expires, the vehicle will enter Mix Mode.
· In ambient temperatures from 40°F (4.5°C) to 78°F (26°C), the climate settings will be based on the last settings selected by the driver.
· In ambient temperatures at 78°F (26°C) or above, the climate settings will default to MAX A/C, Bi-Level Mode, and Recirculation on.
For more information on ATC, MTC, and climate control settings, see page 47.

GETTING TO KNOW YOUR VEHICLE 19

NOTE:

These features will stay on through the duration of

Remote Start until the ignition is placed in the ON/RUN

position. The climate control settings will change if

manually adjusted by the driver while the vehicle is in

Remote Start mode, and exit automatic override. This

2

includes the OFF button on the climate controls, which

will turn the system off.

REMOTE START WINDSHIELD WIPER DE-ICER ACTIVATION — IF EQUIPPED

When Remote Start is active and the outside ambient temperature is less than 33°F (0.6°C), the Windshield Wiper De-Icer will activate. Exiting Remote Start will resume its previous operation. If the Windshield Wiper De-Icer was active, the timer and operation will continue.

REMOTE START CANCEL MESSAGE — IF EQUIPPED

One of the following messages will display in the instrument cluster display if the vehicle fails to remote start or exits Remote Start prematurely:
· Remote Start Canceled — Door Open · Remote Start Canceled — Hood Open · Remote Start Canceled — Fuel Low · Remote Start Canceled — Liftgate Open · Remote Start Canceled — Timer Expired · Remote Start Disabled — Start Vehicle To Reset
The instrument cluster display message stays active until the ignition is placed in the ON/RUN position.

20 GETTING TO KNOW YOUR VEHICLE
VEHICLE SECURITY SYSTEM — IF EQUIPPED
The Vehicle Security system monitors the vehicle doors for unauthorized entry and the Keyless Enter `n GoTM Ignition for unauthorized operation. While the Vehicle Security system is armed, interior switches for door locks and liftgate release are disabled. If something triggers the alarm, the Vehicle Security system will provide the following audible and visible signals:
· The horn will pulse · The parking lights and/or turn signals will flash · The Vehicle Security Light in the instrument cluster
will flash
TO ARM THE SYSTEM
Follow these steps to arm the Vehicle Security system:
1. If any doors, windows, or sunroof are open, close them.
2. Make sure the vehicle’s ignition is placed in the OFF position.
For vehicles equipped with Keyless Entry, make sure the vehicle’s keyless ignition system is OFF.
3. Perform one of the following methods to lock the vehicle:
Push lock on the interior power door lock switch with the driver and/or passenger door open.
Push the lock button on the exterior Passive Entry door handle with a valid key fob available in the same exterior zone page 21.
Push the lock button on the key fob.

TO DISARM THE SYSTEM
The Vehicle Security system can be disarmed using any of the following methods:
· Push the unlock button on the key fob. · Grab the Passive Entry unlock door handle
(if equipped) page 21.
· Cycle the vehicle ignition system out of the OFF position.
NOTE:
· The driver’s door key cylinder cannot arm or disarm the Vehicle Security system. Use of the door key cylinder when the alarm is armed will sound the alarm when the door is opened.
· The Vehicle Security system remains armed when the power liftgate is opened using the liftgate button on the key fob. If someone enters the vehicle through the opened liftgate, then opens any door from the inside, the alarm will sound.
· If Passive Entry (if equipped) is used to unlock the liftgate, the Vehicle Security system is disarmed and the rest of the vehicle doors will remain locked unless all doors are set to unlock on first press within Uconnect Settings.
· When the Vehicle Security system is armed, the interior power door lock switches will not unlock the doors.
The Vehicle Security system is designed to protect your vehicle. However, you can create conditions where the system will give you a false alarm. If one of the previously described arming sequences has occurred, the Vehicle Security system will arm regardless of whether

you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the Vehicle Security system. If the Vehicle Security system is armed and the battery becomes disconnected, the Vehicle Security system will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound. If this occurs, disarm the Vehicle Security system.
REARMING OF THE SYSTEM
If something triggers the alarm and no action is taken to disarm it, the Vehicle Security system will turn the horn off after a 29 second cycle (with five seconds between cycles and up to eight cycles if the trigger remains active) and then rearm itself.
SECURITY SYSTEM MANUAL OVERRIDE
The Vehicle Security system will not arm if you lock the doors using the manual door lock.
TAMPER ALERT
If something has triggered the Vehicle Security system in your absence, the horn will sound three times and the exterior lights will blink three times when you disarm the Vehicle Security system.
DOORS
MANUAL DOOR LOCKS
The power door locks can be manually locked from inside the vehicle by using the door lock knob. To lock each door, push the door lock knob on each door trim panel downward. To unlock the front doors, pull the

inside door handle to the first detent. To unlock the rear doors, pull the door lock knob on the door trim panel upward. If the lock knob is down when the door is closed, the door will lock. Make sure the key fob is not inside the vehicle before closing the door.

WARNING!
· Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter `n GoTM in the ACC or ON/RUN position. A child could operate power windows, other controls, or move the vehicle.
· When leaving the vehicle, always make sure the keyless ignition is in the OFF position, remove the key fob from the vehicle and lock the vehicle. Unsupervised use of the vehicle equipment may cause severe person injuries and death.

Manual Door Lock Knob
WARNING!
· For personal security and safety in the event of a collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
· Never leave children alone in a vehicle, or with access to an unlocked vehicle.
· Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector. (Continued)

POWER DOOR LOCKS
The power door lock switches are located on each front door panel. Push the switch to lock or unlock the doors and liftgate.
Power Door Lock Switches If the lock knob is down when the door is closed, the door will lock. Make sure the key fob is not inside the vehicle before closing the door.

GETTING TO KNOW YOUR VEHICLE 21
NOTE: If the key fob is located next to a mobile phone, laptop, or other electronic device, the wireless signal may get blocked, and the driver’s door may not unlock automatically.
If the door lock switch is pushed while the ignition is in 2
the ACC or ON/RUN position, and the driver’s door is open, the doors will not lock. If a rear door is locked, it cannot be opened from inside the vehicle without first unlocking the door. The door may be unlocked manually by raising the lock knob.
KEYLESS ENTER N GOTM — PASSIVE ENTRY The Passive Entry system is an enhancement to the vehicle’s Remote Keyless Entry (RKE) system and a feature of Keyless Entern GoTM — Passive Entry. This feature allows you to lock and unlock the vehicle’s door(s) without having to push the key fob lock or unlock buttons.
NOTE:
· Passive Entry may be programmed on/off within Uconnect Settings page 135.
· The key fob may not be detected by the vehicle Passive Entry system if it is located next to a mobile phone, laptop or other electronic device; these devices may block the key fob’s wireless signal and prevent the Passive Entry handle from locking/ unlocking the vehicle.

22 GETTING TO KNOW YOUR VEHICLE
· Passive Entry Unlock initiates illuminated approach (low beams, license plate lamp, position lamps) for whichever duration is set between 0, 30, 60 or 90 seconds. Passive Entry unlock also initiates two flashes of the turn signal lamps.
· If wearing gloves, if it has been raining/snowing, or there is salt/dirt covering the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a slower response time.
· The doors may unlock when water is sprayed on the Passive Entry door handles if the key fob is located outside of the vehicle within 5 ft (1.5 m) of the handle.
· If the vehicle is unlocked by Passive Entry and no door is opened within 60 seconds, the vehicle will relock and will arm the Vehicle Security system (if equipped).
To Unlock From The Driver Or Passenger Side:
With a valid Passive Entry key fob within 5 ft (1.5 m) of the door handle, grab the handle to unlock the vehicle. Grabbing the driver’s door handle will unlock the driver door automatically. Grabbing the passenger door handle will unlock all doors and the liftgate automatically. The interior door panel lock knob will raise when the door is unlocked.

Grab The Door Handle To Unlock
NOTE: Either the driver door only or all doors will unlock when you grab hold of the front driver’s door handle, depending on the selected setting in the Uconnect system
page 135.
Preventing Inadvertent Locking Of Passive Entry Key Fob In Vehicle
To minimize the possibility of unintentionally locking a Passive Entry key fob inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature, which will function if the ignition is in the OFF position.
If one of the vehicle doors is open, and the door panel switch is used to lock the vehicle, once all open doors have been closed, the vehicle checks the inside and outside of the vehicle for any valid Passive Entry key fob. If one of the vehicle’s Passive Entry key fobs is detected inside the vehicle, and no other valid Passive Entry key fobs are detected outside the vehicle, the Passive Entry system automatically unlocks all vehicle

doors and chirps the horn three times (on the third attempt, ALL doors will lock, and the Passive Entry key fob can be locked in the vehicle).
To Unlock/Enter The Liftgate
The liftgate Passive Entry unlock feature is built into the electronic liftgate handle. With a valid Passive Entry key fob within 5 ft (1.5 m) of the liftgate, pull the electronic liftgate handle for a power open on vehicles equipped with a power liftgate. Pull the electronic liftgate handle and lift for manual liftgate vehicles.
NOTE:
· If the vehicle is unlocked, the liftgate will open with the handle and no key fob is required.
· The liftgate will either unlock along with the vehicle doors, or it will need to be unlocked by pushing the electronic liftgate release, depending on the selected setting in the Uconnect system page 135.
· The liftgate (and vehicle doors if unlocked) must be locked using the lock button on the key fob, the Passive Entry lock button, or the lock buttons on the interior front door panels.

Electronic Liftgate Handle
1 — Electronic Release Switch 2 — Lock Button Location
To Lock The Liftgate With a valid Passive Entry key fob within 5 ft (1.5 m) of the liftgate, push the Passive Entry lock button located to the right of electronic liftgate handle.
NOTE: When you push the button on the liftgate, either only the liftgate will unlock or all doors and the liftgate will unlock, depending on the selected setting in the Uconnect system page 135. To Lock The Vehicle’s Doors And Liftgate With one of the vehicle’s Passive Entry key fobs within 5 ft (1.5 m) of the driver or passenger front door handle, push the door handle lock button to lock all four doors and liftgate.

NOTE: This feature will cause the horn to chirp when the doors are locked with the door handle lock button. This feature can be turned on or off within Uconnect Settings
page 135.
Push The Door Handle Button To Lock NOTE: Do NOT grab the door handle when pushing the door handle button. This could unlock the door(s).
Do NOT Grab The Door Handle When Locking

GETTING TO KNOW YOUR VEHICLE 23

NOTE:

· After pushing the door handle button, you must wait

two seconds before you can lock or unlock the

doors, using either Passive Entry door handle or

door handle button. This is done to allow you to check if the vehicle is locked by pulling the door

2

handle without the vehicle unlocking.

· The Passive Entry system will not operate if the key fob battery is depleted.

· Close proximity to mobile devices can affect the Passive Entry system.

The vehicle doors can also be locked by using the key fob lock button or the lock button located on the vehicle’s interior door panel page 310.

AUTOMATIC UNLOCK ON EXIT FEATURE — IF EQUIPPED

If Auto Unlock is enabled within Uconnect Settings page 135, this feature will unlock all the doors
when any door is opened if the vehicle is in PARK.

CHILD-PROTECTION DOOR LOCK SYSTEM — REAR DOORS

To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with Child-Protection Door Lock system.
To Engage Or Disengage The Child Protection Door Lock System

1. Open the rear door.

2. Insert the tip of the emergency key into the lock and rotate to the lock or unlock position.

3. Repeat steps 1 and 2 for the opposite rear door.

24 GETTING TO KNOW YOUR VEHICLE
Child-Protection Door Lock Function WARNING!
Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged (locked).

STEERING WHEEL
MANUAL TILT/TELESCOPING STEERING COLUMN — IF EQUIPPED
This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping lever is located below the steering wheel at the end of the steering column.

WARNING!
Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
POWER TILT/TELESCOPING STEERING COLUMN — IF EQUIPPED
This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The power tilt/telescoping steering column control is located below the multifunction lever on the steering column.

NOTE:
For emergency exit with the system engaged, move the lock knob up (unlocked position), lower the window, and open the door with the outside door handle.

Manual Tilt/Telescoping Steering Column Handle
To unlock the steering column, push the lever downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the lever upward until fully engaged.

Power Tilt/Telescoping Steering Control Location Use the four-way control to adjust the steering column.

NOTE: For vehicles equipped with Driver Memory Settings, use the key fob or the memory switch on the driver’s door trim panel to return the tilt/telescopic steering column to saved positions page 25.
WARNING!
Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
HEATED STEERING WHEEL — IF EQUIPPED
The steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on, it will stay on until the operator turns it off. The heated steering wheel may not turn on when it is already warm. The heated steering wheel button is located within the Uconnect system and, if equipped, on the instrument panel below the radio. You can access the button through the Climate or Controls menu of the touchscreen.
· Press the heated steering wheel button once to turn the heating element on.
· Press the heated steering wheel button a second time to turn the heating element off.

NOTE: The engine must be running for the heated steering wheel to operate. For information on use with the Remote Start system, see page 19.
WARNING!
· Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater. It may cause burns even at low temperatures, especially if used for long periods.
· Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type of material. This may cause the steering wheel heater to overheat.
DRIVER MEMORY SETTINGS — IF EQUIPPED
This feature allows the driver to save up to two different memory profiles for easy recall through a memory switch. Each memory profile saves desired position settings for the following features:
· Driver seat · Easy Entry/Exit seat (if equipped) · Side mirrors · Power tilt and telescopic steering column
(if equipped)
· A set of desired radio station presets

GETTING TO KNOW YOUR VEHICLE 25

NOTE:

· Your vehicle is equipped with two key fobs, each can be linked to either memory position 1 or 2.

· Be sure to program the radio presets prior to pro-

gramming the memory settings.

2

The memory setting switch is located on the driver’s

door trim panel. The switch consists of three buttons:

· The set (S) button, which is used to activate the

memory save function.

· The (1) and (2) buttons which are used to recall

either of two saved memory profiles.

Memory Setting Buttons
PROGRAMMING THE MEMORY FEATURE
To create a new memory profile, perform the following:
NOTE: Saving a new memory profile will erase the selected profile from memory.

26 GETTING TO KNOW YOUR VEHICLE
1. Place the vehicle’s ignition in the ON/RUN position (do not start the engine).
2. Adjust all memory profile settings to desired preferences (i.e., seat, side mirror, power tilt and telescopic steering column [if equipped], and radio station presets).
3. Push the set (S) button on the memory switch, and then push the desired memory button (1 or 2) within five seconds. The instrument cluster display will display which memory position has been set.
NOTE: Memory profiles can be set without the vehicle in PARK, but the vehicle must be in PARK to recall a memory profile.
LINKING AND UNLINKING THE REMOTE KEYLESS ENTRY KEY FOB TO MEMORY
Your key fobs can be programmed to recall one of two saved memory profiles.
NOTE: Before programming your key fobs you must select the “Personal Settings Linked To Fob” feature through the Uconnect Settings page 135. To program your key fobs, perform the following:
1. Place the vehicle’s ignition in the OFF position.
2. Select a desired memory profile, 1 or 2.

3. Once the profile has been recalled, push and release the set (S) button on the memory switch. Then, within five seconds, push and release button (1) or (2) accordingly. “Memory Profile Set” (1 or 2) will display in the instrument cluster display.
4. Push and release the lock button on the key fob within 10 seconds.
NOTE: Your key fobs can be unlinked from your memory settings by pushing the set (S) button, and within 10 seconds, followed by pushing the unlock button on the key fob.
MEMORY POSITION RECALL
NOTE: If a recall is attempted when the vehicle is not in PARK, a message will be displayed in the instrument cluster display.
To recall the memory settings for driver one or two, push the desired memory button (1 or 2) or the unlock button on the key fob linked to the desired memory position.
A recall can be canceled by pushing any of the memory buttons during a recall (S, 1, or 2), or by pushing any of the seat adjustment switches. When a recall is canceled, the driver’s seat and telescopic steering column (if equipped) will stop moving. A delay of one second will occur before another recall can be selected.

SEATS
Seats are a part of the Occupant Restraint system of the vehicle.
WARNING!
· It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
· Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed.
· Be sure everyone in your vehicle is in a seat and using a seat belt properly.
MANUAL ADJUSTMENT (FRONT SEATS) — IF EQUIPPED
WARNING!
· Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be adjusted properly and you could be injured. Adjust the seat only while the vehicle is parked.
· Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.

Manual Front Passenger Seat Forward/Rearward Adjustment
Some models may be equipped with a manual front passenger seat. The passenger seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor.

WARNING!
· Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt.
Manual Front Passenger Seatback Adjustment — Recline
To adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired position and release the lever. To return the seatback, lift the lever, lean forward and release the lever.

GETTING TO KNOW YOUR VEHICLE 27

Front Passenger Seat Fold-Flat Feature — If Equipped

To fold the seatback to the flat load-floor position, lift

the recline lever and push the seatback forward. To

return to the seating position, raise the seatback and lock it into place.

2

Adjustment Bar
While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.
WARNING!
· Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. (Continued)

Recline Lever
WARNING!
Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.

Fold-Flat Passenger Seat
WARNING!
· Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted, and you could be severely injured or killed. Only adjust a seat while the vehicle is parked.
· Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision, you could slide under the seat belt and be severely injured or killed. Use the recliner only when the vehicle is parked.

28 GETTING TO KNOW YOUR VEHICLE
CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.
MANUAL ADJUSTMENT (REAR SEATS)
WARNING! Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or collision.
60/40 Split Rear Seat — If Equipped SECOND ROW FOLD-FLAT SEATS
The second row seats can be folded flat to carry cargo. Pull upward on the release lever located on the outboard side of the seat.

EASY ACCESS FOR THIRD ROW
Either side of the rear seat can be tumbled forward to allow passengers to easily access the third row seats.
1. Pull upward on the release lever to release the seat.

Release Lever

Release Lever
2. Tumble the seat forward using the pull strap located behind the seatback.

Fold-Flat Second Row Seats
NOTE: You may experience deformation in the seat cushion from the seat belt buckles if the seats are left folded for an extended period of time. This is normal and by simply unfolding the seats to the open position, over time the seat cushion will return to its normal shape.

Tumble Pull Strap

Tumbled Second Row
WARNING!
Do not drive the vehicle with the second row seats in the tumbled position. The second row seats are only intended to be tumbled for entry and exit to the third row seat. Failure to follow these instructions could result in personal injury.
TO RAISE REAR SEAT
Fold the seat rearward to its original position, and lock it into place. Then lift the head restraint until it locks into place.
WARNING!
Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.

Rear Captain’s Chairs — If Equipped
SECOND ROW CAPTAIN’S CHAIRS FOLD-FLAT SEATS
The second row seats can be folded flat to carry cargo. Pull upward on the release lever located on the outboard side of the seat.

GETTING TO KNOW YOUR VEHICLE 29

NOTE:

You may experience deformation in the seat cushion

from the seat belt buckles if the seats are left folded for

an extended period of time. This is normal and by sim-

ply unfolding the seats to the open position, over time

the seat cushion will return to its normal shape.

2

EASY ACCESS FOR THIRD ROW

Either side of the rear seat can be tumbled forward to allow passengers to easily access the third row seats.

1. Pull upward on the release lever to release the seat.

Release Lever

Release Lever
2. Tumble the seat forward using the pull strap located behind the seatback.

Fold-Flat Second Row Seats

30 GETTING TO KNOW YOUR VEHICLE

Tumble Strap
WARNING!
Do not drive the vehicle with the second row seats in the tumbled position. The second row seats are only intended to be tumbled for entry and exit to the third row seat. Failure to follow these instructions could result in personal injury.
3. If your vehicle is equipped with a mini console, there is a stepping pad to allow passengers to easily access the third row seats.

Mini Console Stepping Pad
TO RAISE REAR SEAT
Fold the seat rearward to its original position, and lock it into place. Then lift the head restraint until it locks into place.

Release Handles

WARNING!
Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
Folding Third Row
Both third row seats can be folded forward to increase the cargo area. To lower either seat, pull on the release handle located on the back of the seat and lower the seat using the pull strap located next to the release handle.

Third Row Folded
NOTE: The second row seats must be in their full upright position, folded flat or tumbled when folding the third row seats. To raise the seat, pull the seat toward you using the strap located on the back of the seat. Then lift the head restraint until it locks into place.

NOTE:
You may experience deformation in the seat cushion from the seat belt buckles if the seats are left folded for an extended period of time. This is normal and by simply unfolding the seats to the open position, over time the seat cushion will return to its normal shape.

WARNING!
Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
POWER ADJUSTMENT (FRONT SEATS) — IF EQUIPPED
Some models may be equipped with eight-way power driver and front passenger seats. The power seat switches are located on the outboard side of the seat. There are two switches that control the movement of the seat cushion and the seatback.

Power Seat Switches
1 — Seatback Switch 2 — Seat Switch
Adjusting The Seat Forward Or Rearward
The seat can be adjusted both forward and rearward by using the seat switch. The seat will move in the direction of the switch. Release the switch when the desired position has been reached.
Adjusting The Seat Up Or Down
The height of the seats can be adjusted up or down. Pull upward or push downward on the rear of seat switch, the seat will move in the direction of the switch. Release the switch when the desired position has been reached.

GETTING TO KNOW YOUR VEHICLE 31

Tilting The Seat Up Or Down

The angle of the seat cushion can be adjusted in two

directions. Pull upward or push downward on the front

of the seat switch, the front of the seat cushion will

move in the direction of the switch. Release the switch

when the desired position has been reached.

2

Reclining The Seatback
The angle of the seatback can be adjusted forward or rearward. Push the seatback switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position is reached.

WARNING!
· Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death.
· Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt.
· Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.

32 GETTING TO KNOW YOUR VEHICLE
CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.
Power Lumbar — If Equipped
Vehicles equipped with power driver or passenger seats may also be equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat. Push the switch forward to increase the lumbar support. Push the switch rearward to decrease the lumbar support. Pushing upward or downward on the switch will raise and lower the position of the support.
Power Lumbar Switch
Easy Entry/Exit Seat — If Equipped
This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle.

The distance the driver seat moves depends on where you have the driver seat positioned when you place the vehicle’s ignition in the OFF position.
· When you place the vehicle’s ignition in the OFF position, the driver seat will move about 2.4 inches (60 mm) rearward if the driver seat position is greater than or equal to 2.7 inches (67.7 mm) forward of the rear stop. The seat will return to its previously set position when you place the vehicle’s ignition in the ACC or RUN position.
· The Easy Entry/Exit feature is not available when the driver seat position is less than 0.9 of an inch (22.7 mm) forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for Easy Exit or Easy Entry.
When enabled in Uconnect Settings, Easy Entry and Easy Exit positions are stored in each Driver Memory Setting profile page 25.
NOTE: The Easy Entry/Exit feature is enabled (or disabled) through the programmable features in the Uconnect system page 135.
HEATED SEATS — IF EQUIPPED
WARNING!
· Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.
(Continued)

WARNING!
· Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.
Front Heated Seats — If Equipped
The front heated seats control buttons are located on the center stack below the radio screen, or within the Uconnect system.
· Press the heated seat switch once to turn the HI setting on.
· Press the heated seat switch a second time to turn the MED setting on.
· Press the heated seat switch a third time to turn the LO setting on.
· Press the heated seat switch a fourth time to turn the heating elements off.
NOTE:
· Once a heat setting is selected, heat will be felt within two to five minutes.
· The engine must be running for the heated seats to operate.
· The level of heat selected will stay on until the operator changes it. For information on use with the Remote Start system, see page 19.

Rear Heated Seats — If Equipped
The two second row outboard seats may be equipped with heated seats. There are two heated seat switches that allow the rear passengers to operate the seats independently. The heated seat switches for each heater are located on the rear of the center console.
You can choose from HI, LO, or off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for HI, one for LO and none for off.
· Push the switch once to turn the HI setting on. · Push the switch a second time to turn the LO setting
on.
· Push the switch a third time to turn the heating elements off.
The level of heat selected will stay on until the operator changes it.
NOTE: The engine must be running for the heated seats to operate.
FRONT VENTILATED SEATS — IF EQUIPPED
The ventilated seats control buttons are located on the center stack below the radio screen, or within the Uconnect system. The fans operate at three speeds: HI, MED, and LO.
· Press the ventilated seat switch once to choose HI. · Press the ventilated seat switch a second time to
choose MED.

· Press the ventilated seat switch a third time to choose LO.
· Press the ventilated seat switch a fourth time to turn the ventilation off.
NOTE: The engine must be running for the ventilated seats to operate. For information on use with the Remote Start system, see page 19.
HEAD RESTRAINTS
Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.
WARNING!
· All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a crash.
· Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision.

GETTING TO KNOW YOUR VEHICLE 33

Front Head Restraints

Your vehicle is equipped with front four-way driver and passenger head restraints.

To raise the head restraint, pull upward on the head

restraint. To lower the head restraint, push the adjustment button, located at the base of the head restraint,

2

and push downward on the head restraint.

NOTE:
The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see an authorized dealer.

Head Restraint Adjustment Button Location
To adjust the head restraint forward, pull the top of the head restraint toward the front of the vehicle as desired and release. To adjust the head restraint rearward, pull the top of the head restraint to the forward most position and release. The head restraint will return to the rear most position.

34 GETTING TO KNOW YOUR VEHICLE
Forward Adjustment
WARNING!
· All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a crash.
· Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision.
Head Restraints — Rear Seats
The head restraints on the outboard seats are not adjustable. They automatically fold forward when the rear seat is folded to a load floor position, but do not return to their normal position when the rear seat is raised. After returning either seat to its upright position, raise the head restraint until it locks in place. The outboard head restraints are not removable.

The center head restraint has limited adjustment. Lift upward on the head restraint to raise it or push downward on the head restraint to lower it.
Rear Head Restraint WARNING!
Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision. Always make sure the outboard head restraints are in their upright positions when the seat is to be occupied. NOTE: For proper routing of a Child Seat Tether, see
page 207.

Head Restraint Removal — Rear Seats
The center head restraint can be adjusted when occupied, or removed for Child Seat Tethering. To remove the head restraint, raise it as far as it can go by pulling upward. Then, push the release button at the base of the post while pulling the head restraint upward. To reinstall the head restraint, put the head restraint posts into the holes and push downward. Then, adjust the head restraint to the appropriate height.
WARNING!
· ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants. Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.
· Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision. Always make sure the outboard head restraints are in their upright positions when the seat is to be occupied.
Center Head Restraint Release Button

NOTE: For proper routing of a Child Seat Tether, see
page 207.
WARNING!
· A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow removed head restraints in a location outside the occupant compartment.
· ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants. Follow the preceding reinstallation instructions prior to operating the vehicle or occupying a seat.

· Do not fold if there are passengers seated in the third row seats.
UCONNECT VOICE RECOGNITION — IF EQUIPPED
INTRODUCING VOICE RECOGNITION
Start using Uconnect Voice Recognition (VR) with these helpful quick tips. It provides the key Voice Commands and tips you need to know to control your Uconnect system.

Power Folding Third Row Head Restraints
For improved visibility when in REVERSE, the third row head restraints can be folded using the Uconnect system.
Press the Controls button located on the bottom of the Uconnect display.
Press the Headrest Fold button to power fold the third row head restraints.

NOTE:
· The head restraints can only be folded downward using the Headrest Fold button. The head restraints must be raised manually when occupying the third row.

Uconnect 4C/4C NAV With 8.4-inch Display Voice Recognition

GETTING TO KNOW YOUR VEHICLE 35

BASIC VOICE COMMANDS

The following Voice Commands can be given at any point while using your Uconnect system.

Push the VR button or for the Uconnect 5 NAV With

10.1-inch Display, say the vehicle’s Wake Up word, “Hey Uconnect”. After the beep, say:

2

· ” Cancel” to stop a current voice session · ” Help” to hear a list of suggested Voice Commands · ” Repeat” to listen to the system prompts again

Notice the visual cues that inform you of your voice recognition system’s status. Cues appear on the touchscreen.

NOTE:
On Uconnect 5 systems, the factory default Wake Up word is set to “Hey Uconnect” and can be reprogrammed through the Uconnect Settings.

GET STARTED
All you need to control your Uconnect system with your voice are the buttons on your steering wheel.
Helpful hints for using Voice Recognition:
· Reduce background noise. Wind and passenger conversations are examples of noise that may impact recognition.
· Speak clearly at a normal pace and volume while facing straight ahead.
· Each time you give a Voice Command, first push the VR button, wait until after the beep, then say your Voice Command. You can also say the vehicle Wake Up word and state your command. Some examples of Wake Up words include “Hey Uconnect” or “Hey Dodge”.

36 GETTING TO KNOW YOUR VEHICLE
· A passenger can press the VR button shortcut on the radio status bar to also issue a command.
· You can interrupt the help message or system prompts by pushing the VR button and saying a Voice Command from the current category.
Uconnect Voice Command Buttons
1 — Push To Answer An Incoming Phone Call 2 — For The Uconnect 4C/4C NAV With 8.4-inch Display: Push The Voice Recognition Button To Start A Phone Call, Begin Radio, Media, Navigation (If Equipped) And Climate Functions, Or Send Or Receive A Text 2 — For The Uconnect 5/5 NAV System Vehicles Equipped With Navigation: Push The Voice Recognition Button To Begin Radio, Media, Navigation, Climate, Start Or Answer A Phone Call, And Send Or Receive A Text 2 — For The Uconnect 5/5 NAV System Vehicles Not Equipped With Navigation: Push The Phone Button To Answer An Incoming Phone Call

ADDITIONAL INFORMATION
© 2023 FCA US LLC. All rights reserved. Mopar and Uconnect are registered trademarks and Mopar Owner Connect is a trademark of FCA US LLC. SiriusXM® and all related marks and logos are trademarks of SiriusXM® Radio Inc. page 310.
Uconnect System Support:
· US residents visit www.DriveUconnect.com or call: 1-877-855-8400 (24 hours a day 7 days a week)
· Canadian residents visit www.DriveUconnect.ca or call: 1-800-465-2001 (English) or 1-800-387-9983 (French)
Brand Connect services support:
· US residents visit https://www.driveuconnect.com/ or call: 1-833-616-7527
· Canadian residents visit https://www.driveuconnect.ca/en or call: 1-833-648-1611
MIRRORS

You can turn the feature on or off by pushing the button at the base of the mirror. A light in the button will illuminate to indicate when the dimming feature is activated. Some vehicles may be equipped with an auto dimming mirror with no on/off button in the mirror. If that is the case, the mirror will default to auto dimming on and the feature can be disabled in the radio though the button on the touchscreen.
Automatic Dimming Mirror
ILLUMINATED VANITY MIRRORS
To access an illuminated vanity mirror, flip down one of the visors and lift the cover.

INSIDE REARVIEW MIRROR
Automatic Dimming Mirror
The rearview mirror can be adjusted up, down, left, and right. The mirror should be adjusted to center on the view through the rear window. This mirror automatically adjusts for headlight glare from vehicles behind you.
NOTE: The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve rear view viewing.

Illuminated Vanity Mirror

Sun Visor Slide-On-Rod Feature — If Equipped
The sun visor Slide-On-Rod feature allows for additional flexibility in positioning the sun visor to block out the sun.
1. Fold down the sun visor.
2. Unclip the visor from the corner clip.
3. Pivot the sun visor toward the side window.
4. Extend the sun visor blade for additional sun blockage.
NOTE: The sun visor blade can also be extended while the sun visor is against the windshield for additional sun blockage through the front of the vehicle.
OUTSIDE MIRRORS
The outside mirror(s) can be adjusted to the center of the adjacent lane of traffic to achieve the optimal view.
WARNING!
Vehicles and other objects seen in an outside convex mirror will look smaller and farther away than they really are. Relying too much on side convex mirrors could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in a side convex mirror.

Outside Mirrors Folding Feature
All outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions:
· Full forward position · Full rearward position · Normal position
OUTSIDE MIRRORS WITH TURN SIGNAL — IF EQUIPPED
Driver and passenger outside mirrors with turn signal lighting contain LEDs, which are located in the lower outer corner of each mirror.
The LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle. Turning on the Hazard Warning flashers will also activate these LEDs.
OUTSIDE AUTOMATIC DIMMING MIRROR — IF EQUIPPED
The driver’s side outside mirror will automatically adjust for glare from vehicles behind you. This feature is controlled by the inside automatic dimming mirror. The mirror will automatically adjust for headlight glare when the inside mirror adjusts.

GETTING TO KNOW YOUR VEHICLE 37

POWER MIRRORS — IF EQUIPPED

The power mirror switch is located on the driver’s side door trim panel.

The power mirror controls consist of mirror select but-

tons and a four-way mirror control switch. To adjust a mirror, push the mirror select button for the mirror that

2

you want to adjust. Using the mirror control switch,

push on any of the four arrows for the direction that you

want the mirror to move.

Power Mirror Switch
1 — Left Mirror Selection 2 — Mirror Direction Control 3 — Right Mirror Selection
Power mirror positions can be saved to a Driver Memory Settings profile (if equipped) page 25.

38 GETTING TO KNOW YOUR VEHICLE
HEATED MIRRORS — IF EQUIPPED
These mirrors are heated to melt frost or ice. This feature will be activated whenever you turn on the rear window defroster (if equipped) page 47.
UNIVERSAL GARAGE DOOR OPENER (HomeLink®) — IF EQUIPPED

HomeLink® Buttons And Indicator Light

Use this QR code to access your digital experience.

· HomeLink® replaces up to three

hand-held transmitters that operate devices such as garage door open-

Scan me

ers, motorized gates, lighting, or

home security systems. The HomeLink® unit is pow-

ered by your vehicle’s 12 Volt battery.

· The HomeLink® buttons that are located in the overhead console or sun visor designate the three different HomeLink® channels.
· To operate HomeLink®, push and release any of the programmed HomeLink® buttons. These buttons will activate the devices they are programmed to with each press of the corresponding HomeLink® button.
· The HomeLink® indicator light is located above the center button.
NOTE: HomeLink® is disabled when the Vehicle Security system is active page 310.
BEFORE YOU BEGIN PROGRAMMING HOMELINK®
For efficient programming and accurate transmission of the Radio Frequency (RF) signal, it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system. Make sure your hand-held transmitter is programmed to activate the device you are trying to program your HomeLink® button to.
Ensure that your vehicle is parked outside of the garage before you begin programming.
It is recommended that you erase all the channels of your HomeLink® before you use it for the first time.
ERASING ALL THE HOMELINK® CHANNELS
To erase the channels, follow this procedure:
1. Place the ignition switch in the ON/RUN position.

2. Push and hold the two outside HomeLink® buttons (I and III) for up to 20 seconds, or until the HomeLink® indicator light flashes.
NOTE: Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons.
IDENTIFYING WHETHER YOU HAVE A ROLLING CODE OR NON-ROLLING CODE DEVICE
Before programming a device to one of your HomeLink® buttons, you must determine whether the device has a rolling code or non-rolling code.
Rolling Code Devices
To determine if your device has a rolling code, a good indicator is its manufacturing date. Typically, devices manufactured after 1995 have rolling codes. A device with a rolling code will also have a “LEARN” or “TRAIN” button located where the antenna is attached to the device. The button may not be immediately visible when looking at the device. The name and color of the button may vary slightly by manufacturer.
NOTE: The “LEARN” or “TRAIN” button is not the button you normally use to operate the device.
Non-rolling Code Devices
Most devices manufactured before 1995 will not have a rolling code. These devices will also not have a “LEARN” or “TRAIN” button.

PROGRAMMING HOMELINK® TO A GARAGE DOOR OPENER
To program any of the HomeLink® buttons to activate your garage door opener motor, proceed as follows:
NOTE: All HomeLink® buttons are programmed using this procedure. You do not need to erase all channels when programming additional buttons.
1. Place the ignition switch in the ON/RUN position.
2. Place the garage door opener transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to program, while keeping the HomeLink® indicator light in view.
3. Push and hold the HomeLink® button you want to program while you push and hold the garage door opener transmitter button you are trying to replicate.
4. Continue to hold both buttons and observe the HomeLink® indicator light. The HomeLink® indicator light will flash slowly and then rapidly. Once this happens, release both buttons.
NOTE: Make sure the garage door opener motor is plugged in before moving on to the rolling code/non-rolling code final steps. Rolling Code Garage Door Opener Final Steps
NOTE: You have 30 seconds in which to initiate rolling code final step 2, after completing rolling code final step 1.

1. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAIN” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor. Firmly push and release the “LEARN” or “TRAIN” button.
2. Return to the vehicle and push the programmed HomeLink® button three times (holding the button for two seconds each time). If the garage door opener motor operates, programming is complete.
3. Push the programmed HomeLink® button to confirm that the garage door opener motor operates. If the garage door opener motor does not operate, repeat the final steps for the rolling code procedure.
Non-Rolling Code Garage Door Opener Final Steps
1. Push and hold the programmed HomeLink® button and observe the HomeLink® indicator light. If the HomeLink® indicator light stays on constantly, programming is complete.
2. Push the programmed HomeLink® button to confirm that the garage door opener motor operates. If the garage door opener motor does not operate, repeat the steps from the beginning.
WARNING!
· Your motorized door or gate will open and close while you are programming the universal transmitter. Do not program the transmitter if people or pets are in the path of the door or gate.
· Do not run your vehicle in a closed garage or confined area while programming the transmitter. Exhaust gas from your vehicle contains carbon monoxide (CO) which is odorless and colorless.
(Continued)

GETTING TO KNOW YOUR VEHICLE 39
WARNING!
Carbon monoxide is poisonous when inhaled and can cause you and others to be severely injured or killed.
2 PROGRAMMING HOMELINK® TO A MISCELLANEOUS DEVICE
The procedure on how to program HomeLink® to a miscellaneous device follows the same procedure as programming to a garage door opener page 39. Be sure to determine if the device has a rolling code, or non-rolling code before beginning the programming process.
NOTE: Canadian Radio Frequency (RF) laws require transmitter signals to time- out (or quit) after several seconds of transmission, which may not be long enough for HomeLink® to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner. The procedure may need to be performed multiple times to successfully pair the device to your HomeLink® buttons.
REPROGRAMMING A SINGLE HOMELINK® BUTTON
To reprogram a single HomeLink® button that has been previously trained, without erasing all the channels, proceed as follows. Be sure to determine whether the new device you want to program the HomeLink® button to has a rolling code, or non-rolling code.

40 GETTING TO KNOW YOUR VEHICLE
1. Place the ignition in the ON/RUN position, without starting the engine.
2. Push and hold the desired HomeLink® button until the HomeLink® indicator light begins to flash after 20 seconds. Do not release the button.
3. Without releasing the button, proceed with Step 2 in “Programming HomeLink® To A Garage Door Opener” and follow all remaining steps.
CANADIAN/GATE OPERATOR PROGRAMMING
For programming transmitters in Canada/United States that require the transmitter signals to “time-out” after several seconds of transmission: Canadian Radio Frequency (RF) laws require transmitter signals to time-out (or quit) after several seconds of transmission, which may not be long enough for HomeLink® to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor.
1. Place the ignition in the ON/RUN position.
NOTE: For vehicles equipped with Keyless Enter `n GoTM, place the ignition in the RUN position. Make sure while programming HomeLink® with the engine on that your vehicle is outside of your garage, or that the garage door remains open at all times.

2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view.
3. Continue to push and hold the HomeLink® button while you push and release (cycle) your hand-held transmitter every two seconds until HomeLink® has successfully accepted the frequency signal. The indicator light will flash slowly and then rapidly when fully trained.
4. Watch for the HomeLink® indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you are programming.
5. Push and hold the programmed HomeLink® button and observe the indicator light.
NOTE:
If the indicator light stays on constantly, programming is complete and the garage door/device should activate when the HomeLink® button is pushed.
To program the two remaining HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels.
If you unplugged the garage door opener/device for programming, plug it back in at this time.
Reprogramming A Single HomeLink® Button (Canadian/Gate Operator)
To reprogram a channel that has been previously trained, follow these steps:
1. Place the ignition in the ON/RUN position.

2. Press and hold the desired HomeLink® button until the indicator light begins to flash after 20 seconds. Do not release the button.
3. Without releasing the button, proceed with “Canadian/Gate Operator Programming” Step 2 and follow all remaining steps.
SECURITY
It is advised to erase all channels before you sell or turn in your vehicle.
To do this, push and hold the two outside buttons for 20 seconds until the indicator flashes. Note that all channels will be erased. Individual channels cannot be erased.
The HomeLink® universal transmitter is disabled when the Vehicle Security system is active.
TROUBLESHOOTING TIPS
If you are having trouble programming HomeLink®, here are some of the most common solutions:
· Replace the battery in the garage door opener handheld transmitter.
· Push the LEARN button on the garage door opener to complete the training for a rolling code.
· Did you unplug the device for programming and remember to plug it back in?
If you have any problems, or require assistance, please call toll-free 1-800-355-3515 or on the Internet at HomeLink.com for information or assistance.

WARNING!
· Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run your vehicle in the garage while programming the transmitter. Exhaust gas can cause serious injury or death.
· Your motorized door or gate will open and close while you are programming the universal transmitter. Do not program the transmitter if people, pets or other objects are in the path of the door or gate. Only use this transmitter with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features.
EXTERIOR LIGHTS
MULTIFUNCTION LEVER
The multifunction lever is located on the left side of the steering column.
Multifunction Lever

HEADLIGHT SWITCH
The headlight switch is located on the left side of the instrument panel, next to the steering wheel. The headlight switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped).
Headlight Switch 1 — Rotate Headlight Switch 2 — Dimmer Control 3 — Fog Light Switch

GETTING TO KNOW YOUR VEHICLE 41
2
Headlight Switch (Vehicles Sold In Canada)
1 — Rotate Headlight Switch 2 — Dimmer Control 3 — Fog Light Switch
NOTE: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent. Headlights will be deactivated when the headlight switch is placed in the parking lights position. However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights. The DRLs may be deactivated when the parking brake is engaged. To turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on, the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the O (off) position.

42 GETTING TO KNOW YOUR VEHICLE
NOTE: For vehicles sold in Canada, rotate the headlight switch clockwise from the parking lights and instrument panel lights position to the first detent to turn on headlights, parking lights, and instrument panel lights. Rotate the headlight switch to the second detent for the AUTO position.
NOTE:
· Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less susceptible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
· To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing.
CAUTION!
Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses.
DAYTIME RUNNING LIGHTS (DRLS)
The Daytime Running Lights (DRLs) come on whenever the engine is running. The lights will remain on until the ignition is placed in the OFF position, or the parking brake is engaged. The headlight switch must be used during normal nighttime driving.

NOTE:
· For vehicles sold in Canada, the Daytime Running Lights will automatically deactivate when the front fog lights are turned on.
· If allowed by law in the country in which the vehicle was purchased, the Daytime Running Lights can be turned on and off using the Uconnect system page 135.
· On some vehicles, the Daytime Running Lights may deactivate or reduce intensity on one side of the vehicle (when a turn signal is activated on that side), or on both sides of the vehicle (when the hazard warning lights are activated).
HIGH/LOW BEAM SWITCH
Push the multifunction lever toward the instrument panel to switch the headlights to high beams. Pulling the multifunction back will turn the low beams on.
AUTOMATIC HIGH BEAM — IF EQUIPPED
The Automatic High Beam Headlamp Control system provides increased forward lighting at night by automatically controlling the high beams through the use of a camera mounted on the inside rearview mirror. This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view.

NOTE:
· The Automatic High Beam Headlamp Control can be turned on or off by selecting or deselecting “Auto Dim High Beams” within your Uconnect Settings page 135, as well as turning the headlight switch to the AUTO position.
· Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.
· If the windshield or Automatic High Beam Headlamp Control mirror is replaced, the mirror must be re-aimed to ensure proper performance. See a local authorized dealer.
· To opt out of the Advanced Auto High-Beam Sensitivity Control (default) and enter Reduced High-Beam Sensitivity Control (not recommended), toggle high beam lever six full on/off cycles within 10 seconds of ignition ON. System will return to default setting upon ignition off.
FLASH-TO-PASS
You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will cause the high beam headlights to turn on, and remain on, until the lever is released.

AUTOMATIC HEADLIGHTS
This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch counterclockwise to the AUTO position. When the system is on, the headlight time delay feature is also on. This means the headlights will stay on for up to 90 seconds after you place the ignition into the OFF position. The headlight time delay can be programmed 0/30/60/90 seconds within Uconnect Settings page 135.
To turn the automatic system off, move the headlight switch out of the AUTO position.
NOTE: The engine must be running before the headlights will come on in the automatic mode.
PARKING LIGHTS AND PANEL LIGHTS
To turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise. To turn off the parking lights, rotate the headlight switch back to the O (off) position.
NOTE: Vehicles sold in Canada are equipped with a headlight switch with an AUTO and ON detent but without an OFF detent. Headlights will be deactivated when the headlight switch is placed in the parking lights position. However, the Daytime Running Lights (DRLs) will be activated along with the front and rear marker lights. The DRLs may be deactivated when the parking brake is engaged.

AUTOMATIC HEADLIGHTS WITH WIPERS
If your vehicle is equipped with Automatic Headlights, it also has this customer-programmable feature. When your headlights are in the automatic mode and the engine is running, they will automatically turn on when the wiper system is on. This feature is programmable through the Uconnect system page 135.
NOTE: When your headlights come on during the daytime, the vehicle will monitor outside brightness and decide if the instrument panel needs to be dimmed or not
page 45.
HEADLIGHT DELAY
To assist when exiting the vehicle, the headlight delay feature will leave the headlights on for up to 90 seconds. This delay is initiated when the ignition is placed in the OFF position while the headlight switch is on, and then the headlight switch is cycled off. Headlight delay can be canceled by either turning the headlight switch on then off, or by placing the ignition in the ON position.
NOTE: The headlight delay timing is programmable through the Uconnect system page 135.
LIGHTS-ON REMINDER
If the headlights, parking lights, or cargo lights are left on after the ignition is placed in the OFF position, the vehicle will chime when the driver’s door is opened.

GETTING TO KNOW YOUR VEHICLE 43

TURN SIGNALS

Move the multifunction lever up or down to activate the turn signals. The arrows on each side of the instrument cluster flash to show proper operation.

NOTE:

2

If either light remains on and does not flash, or there is

a very fast flash rate, check for a defective outside light

bulb.

LANE CHANGE ASSIST — IF EQUIPPED
Lightly push the multifunction lever up or down, without moving beyond the detent, and the turn signal will flash three times then automatically turn off.

AUTOMATIC HEADLIGHT LEVELING — IF EQUIPPED
This feature prevents the headlights from interfering with the vision of oncoming drivers. Headlight leveling automatically adjusts the height of the headlight beam in reaction to changes in vehicle pitch.

BATTERY SAVER

Timers are set to both the interior and exterior lights to protect the life of your vehicle’s battery.
After 10 minutes, if the ignition is OFF and any door is left open or the dimmer control is rotated all the way up to the dome light on position, the interior lights will automatically turn off.

NOTE: Battery saver mode is canceled if the ignition is ON.

44 GETTING TO KNOW YOUR VEHICLE
If the headlights remain on while the ignition is placed in the OFF position, the exterior lights will automatically turn off after eight minutes. If the headlights are turned on and left on for eight minutes while the ignition is OFF, the exterior lights will automatically turn off.
INTERIOR LIGHTS
Courtesy and dome lights are turned on when the front doors are opened or when the dimmer control is rotated to its upward most position. If your vehicle is equipped with a key fob and the unlock button is pushed, the courtesy and dome lights will turn on. When a door is open and the interior lights are on, rotating the dimmer control all the way down, to the O (off) position, will cause all the interior lights to go out. This allows the doors to stay open for extended periods of time without discharging the vehicle’s battery.
COURTESY LIGHTS
The courtesy lights can be turned on by pushing the top corner of the lens. To turn the lights off, push the lens a second time.

To turn the lights off, push the switch a second time. The lights also turn on when a door is opened. The lights will also turn on when the unlock button on the key fob is pushed.

Courtesy Lights
FRONT MAP/READING LIGHTS — IF EQUIPPED
Lights are mounted in the overhead console. Each light can be turned on by pushing the switch on either side of the console. These buttons are backlit for nighttime visibility.

Front Map/Reading Light Switches
AMBIENT LIGHT — IF EQUIPPED
The overhead console is equipped with an ambient light feature. This light illuminates for improved visibility of the floor and center console area.

Front Map/Reading Lights

Ambient Light

DIMMER CONTROL
The brightness of the instrument panel lighting can be regulated by rotating the dimmer control up (brighter) or down (dimmer). When the headlights are on you can supplement the brightness of the odometer, trip odometer, radio and overhead console by rotating the control to its upward most position until you hear a click. This is useful when headlights are required during the day.
Dimmer Control
Dimmer Control (Vehicles Sold In Canada)

ILLUMINATED ENTRY
When programmed with the Uconnect system, the headlights and courtesy lights will turn on when you use the key fob to unlock the doors or open any door
page 135.
The time the lights stay on is programmable up to 90 seconds. The lights will fade to off after the programmed time, or they will immediately fade to off once the ignition switch is placed in the ON/RUN position from the OFF position.
The front courtesy overhead console and door courtesy lights will not turn off if the instrument panel dimmer switch is rotated to the upward most position, past the detent. The overhead and door courtesy lights will turn off after 10 minutes when the ignition is placed in the OFF position to protect the battery.
The illuminated entry system will not operate if the instrument panel dimmer switch is rotated all the way downward to the O (off) position.
WINDSHIELD WIPERS AND WASHERS
The windshield wiper/washer controls are located on the multifunction lever on the left side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever.
WINDSHIELD WIPER OPERATION
Rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high wiper operation.

GETTING TO KNOW YOUR VEHICLE 45

CAUTION!

Always remove any buildup of snow that prevents the

windshield wiper blades from returning to the parked

position. If the windshield wiper switch is turned off,

and the blades cannot return to the parked position,

2

damage to the wiper motor may occur.

Windshield Wiper Operation
1 — Push End Of Lever And Hold For Front Washer 2 — Rotate Downward For Mist 3 — Rotate For Rear Wiper/Washer Operation 4 — Rotate For Front Wiper Operation
Intermittent Wipers Use one of the four intermittent wiper settings when weather conditions make a single wiping cycle, with a variable delay between cycles, desirable. At driving speeds above 10 mph (16 km/h), the delay can be regulated from a maximum of approximately 18 seconds between cycles (first detent), to a cycle every one second (fourth detent). If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled.

46 GETTING TO KNOW YOUR VEHICLE
Windshield Washers To use the washer, push on the end of the lever (toward the steering wheel) and hold. If the lever is pushed while in the intermittent setting, the wipers will turn on and operate for several cycles after the end of the lever is released, and then resume the intermittent interval previously selected. If the end of the lever is pushed while the wipers are in the off position, the wipers will operate for several cycles, then turn off.
NOTE: As a protective measure, the washer will stop if the switch is held for more than 20 seconds. Once the switch is released the washer will resume normal operation.
WARNING!
Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
Mist Rotate the end of the lever downward to the MIST position and release for a single wiping cycle.
NOTE: The Mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The washer function must be used in order to spray the windshield with washer fluid.

For information on wiper care and replacement, see page 269.
RAIN SENSING WIPERS — IF EQUIPPED
This feature senses rain or snowfall on the windshield and automatically activates the wipers. Rotate the end of the multifunction lever to one of four detent positions to activate this feature. The sensitivity of the system can be adjusted with the multifunction lever. Wiper delay position one is the least sensitive, and wiper delay position four is the most sensitive. Setting three is preferred by the average driver during normal rain conditions.
NOTE:
· The Rain Sensing feature will not operate when the wiper switch is in the low or high-speed position.
· The Rain Sensing feature may not function properly when ice, or dried salt water is present on the windshield.
· Use of products containing wax or silicone may reduce Rain Sensing performance.
· The Rain Sensing feature can be turned on and off using the Uconnect system page 135.

The Rain Sensing system has protection features for the wiper blades and arms, and will not operate under the following conditions:
· Low Ambient Temperature — When the ignition is first placed in the ON position, the Rain Sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 3 mph (5 km/h), or the outside temperature is greater than 32°F (0°C).
· Transmission In NEUTRAL Position — When the ignition is in the ON position, and the gear selector is in NEUTRAL, the Rain Sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 3 mph (5 km/h), or the gear selector is moved out of NEUTRAL.
REAR WINDOW WIPER/WASHER
The rear wiper/washer controls are located on the multifunction lever on the left side of the steering column. The rear wiper/washer is operated by rotating a switch, located at the middle of the lever.
Rotate the center portion of the lever upward to the first detent for intermittent operation and to the second detent for continuous rear wiper operation.
Rotate the center portion of the lever upward to the third detent to activate the washer. The washer will continue to operate as long as the switch is held.
Rotate the center portion downward from the OFF position to activate the rear washer. The washer will continue to operate as long as the switch is held.

NOTE: As a protective measure, the pump will stop if the switch is held for more than 20 seconds. Once the switch is released the pump will resume normal operation. If the rear wiper is operating when the ignition is placed in the OFF position, the wiper will automatically return to the “park” position.
CLIMATE CONTROLS
The Climate Control system allows you to regulate the temperature, air flow, and direction of air circulating throughout the vehicle. The controls are located on the touchscreen and on the instrument panel below the radio.
AUTOMATIC CLIMATE CONTROL DESCRIPTIONS AND FUNCTIONS
Uconnect 5/5 NAV With 10.1-inch Display Temperature Controls

Uconnect 4 With 8.4-inch Display Temperature Controls
Max A/C Button
Press and release the MAX A/C button on the touchscreen to change the current setting to the coldest output of air. The MAX A/C indicator illuminates when MAX A/C is ON. Pressing this button or function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off. In MAX A/C, the blower level and mode position can be adjusted to desired user settings. Pressing other settings will cause the MAX A/C to exit.
NOTE: The MAX A/C button is only available on the touchscreen.
A/C Button
Press and release this button on the touchscreen to change the current setting. The A/C indicator illuminates when A/C is on.

GETTING TO KNOW YOUR VEHICLE 47

The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system. When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin.

NOTE:

2

If fog or mist appears on the windshield or side glass, select Defrost mode and increase blower speed if needed. If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects. Clean with a gentle water spray from the front of the radiator and through the condenser.

Recirculation Button
Press and release this button to change the system between recirculation mode and outside air mode. The Recirculation indicator and the A/C indicator illuminate when the Recirculation button is pressed. Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present. Recirculation can be used in all modes. Recirculation may be unavailable (button on the touchscreen grayed out) if conditions exist that could create fogging on the inside of the windshield. The A/C can be deselected manually without disturbing the mode control selection. Continuous use of Recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. Recirculation mode may automatically adjust to optimize customer experience for warming, cooling, dehumidification, etc.

48 GETTING TO KNOW YOUR VEHICLE
AUTO Button
Press and release this button on the touchscreen, or push the button on the faceplate, to change the current setting. The AUTO button automatically controls the interior cabin temperature by adjusting distribution and amount of airflow. Air Conditioning (A/C) may be active during AUTO operation to improve performance. Performing this function will cause the system to switch between manual mode and automatic modes. AUTO mode is highly recommended for efficiency page 52.
Front Defrost Button
Press and release the touchscreen button, or push and release the button on the faceplate, to change the current airflow setting to Defrost mode. The Front Defrost indicator illuminates when the Front Defrost is on. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level may increase. Use Defrost mode with maximum temperature settings for best w

References

• RSA Help
• Roadside Aid
• Homelink
• Official Mopar Site | Owner's Manual
• Chrysler Canada Owners
• Uconnect ® Bluetooth Phone Pairing Instructions | Mopar®
• Uconnect for Chrysler, FIAT, Jeep, Dodge & RAM | Canada
• Uconnect®: Connected Services for Jeep®, Ram, Dodge and More
• Uconnect® and SiriusXM Guardian - Privacy Policy
• SiriusXM Guardian™ - Uconnect® System Services
• dtsc.ca.gov/hazardouswaste/perchlorate
• Official Mopar Site | Service, Parts, Accessories & More
• Official Mopar Site | Owner's Manual
• Child Safety | NHTSA
• Chrysler Canada Owners
• Chrysler Canada Owners
• P65Warnings.ca.gov/passenger-vehicle
• Safer Car Vehicle Safety, Ratings and Recalls | NHTSA
• Safer Car Vehicle Safety, Ratings and Recalls | NHTSA
• Music, Sports, Talk, and Podcasts | SiriusXM Canada
• Music, Sports, Talk, and Podcasts | SiriusXM Canada
• SiriusXM: Music, Sports, Talk & Podcasts, Live & On Demand
• SiriusXM: Music, Sports, Talk & Podcasts, Live & On Demand
• Child car seat safety
• TechAuthority
• TOP TIER - High-quality Fuel Performance Standard - TOP TIER™
• Uconnect ® Bluetooth Phone Pairing Instructions | Mopar®
• Homelink
• AT&T
• AT&T
• Chrysler Canada Owners
• SiriusXM Guardian Privacy Policy - SiriusXM Connected Vehicle Services
• Uconnect for Chrysler, FIAT, Jeep, Dodge & RAM | Canada
• Uconnect & SiriusXM Guardian | Canada
• Uconnect® System - For Chrysler, Dodge, FIAT®, Jeep® and Ram

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>