FLASH F7100762 ART StrobeFX 1000 IP65 User Manual

StrobeFX 1000 IP65
User Manual

INTRODUCTION

We are glad that you have chosen StrobeFX 1000 IP65, thereby expanding your lighting fixtures workshop. We hope that the choice of this device will meet your expectations and stimulate creativity in subsequent lighting projects.
FOR SAFETY REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.

SAFETY INFORMATION

WARNING! The Led Moving Head (LMH) has a powerful pan and tilt motor. The torque reaction when the head is panned suddenly can cause the base to move if the fixture is standing unsecured on a surface. Do not apply power to the LMH unless the baase is securely fastened to a surface or to rigging hardware.
WARNING! Use 2 clamps to rig the fixture. Do not hang the fixture from only one clamp. Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
WARNING! When clamping the fixture to a truss or other structure at any other angle than with the yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
WARNING! Do not look directly at the light spot while the fixture is on.
IMPORTANT! Do not point strong light output from other fixtures at the lamp, as intense illumination can damaged the display.
WARNING! Before operating, ensure that the voltage and frequency of power supply match the power requirements of the fixture. It’s important to ground the yellow/green conductor to earth in order to avoid electric shock. Do not touch any wire during operation and there might be a hazard of electric shock. To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture. Do not connect the device to any dimmer pack.
IMPORTANT! Unpack and check carefully there is no transportation damage before using the fixture. In the event of ser i ous operat i ng problem, stop using the fixture immediately. Never try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts. Disconnect main power before servicing and maintenance.
The housing must be replaced if they are visibly damaged.
IMPORTANT! Maximum ambient temperature is: 40°C Don’t operate it where the temperature is higher than this.

UNPACKING

The following item are included inside the box:

1. – Art StrobeFX 1000 IP65 (1pc)
2. – DMX cable (1pc)
3. – powerCON TRUE1 cable (1pc)
4. – Safety cable (1pc)
5. – Omega (2pcs)
6. – User manual (1pc)

Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet.

INSTALATION

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight
of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it. flown above the ground. Rig the fixture to a support truss or structure using the supplied brackets and suitable clamps.
Fasten a safety cable between the support structure and the attachment point on the fixture. The safety cable must be able to bear at least 10 times the weight of the fixture.
The fixture may be installed in any orientation, but if installed horizontally with a downward beam-angle, water can potentially pool in the fan wells. Under normal operation the moisture will evaporate. However, in locations with high rainfall, you may wish to fabricate a rain shield above the fixture, or modify the position and orientation of the fixture to minimize pooling.
Two quarter-turn brackets are supplied with the fixtre if it is to be IMPORTANT: If any slack is detected between the hook and the device, immediately tighten the mounting screws or skip the device during installation

CONNECTION

The device is equipped with the following interfaces:

1. DMX (in/out): XLR 3-pin socket
2. EHTERNET (in/out): RJ-45 socket
3. Power (in/out): powerCON TRUE1 socket

The connection is performed using cable with XLR-female -> XLR-Male plugs OR Ethernet (RJ-45) cable.
CAUTION! At the last fixture, the DMX signal has to be terminated with a terminator. Solder a 120Ω resistor between signal (-) and signal (+) into a XLR plug and plug it in the DMX output of the last fixture.The connection is performed using power cable with powerCON TRUE1 connector (included). The device must be operated by qualified personnel.
CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only on the manufacturer or by a person with appropriate permissions Using lamp, the change rate of power voltage should be within ±10%, if the voltage is too high, it will shorten the light’s life; if it’s not enough, the lamp will be dark.
Please restart it after turning off light for 20 minutes until full-cooling. Frequent switching will reduce the life span of lamps and bulbs; intermittent using will improve the life of bulbs and lamps.
IMPORTANT! The maximum number of devices connected in series via power cable is 3 pcs.
Voltage Specyfication

Set DMX Address

• To enter the MENU enter the password (if password is turned on). The password is UP, DOWN, UP, DOWN.
• Find DMX on menu, and press ENTER to enter into.
• Set needed DMX Address using the UP and DOWN buttons.
• Press ENTER to save.
• Press the MENU to exit.

Set ArtNet config

• Find NET on menu, and press ENTER to enter into.
• Go to IP ADRESS to set needed IP address (generally ArtNet works on IP range 2.x.x.x, or 10.x.x.x) on your network.
• Go to Subnet mask to choose needed Subnet mask.
• Go to SET UNIVERSES to give Control (master dimmer and shutter), and LED (pixels). Do not forget that artnet is counted from universe 0.
• Control has main addres of the lamp. The address for pixel mapping always starts with 1. Control of Beams is on universe X, AURA on universe X+1.
• Enjoy your lamp with pixel mapping!

DMX CHART

FIXTURE MODES
14 channels – standard
23 channels – standard + macros
68 channels – standard + macros + pixel control aUra + Beam
5-net – artnet control only – main control + Beam control + aUra control

6-42
43-85
86-128
129-171
172-214
215-255| NO STROBE
STROBE TYPE 1
STROBE TYPE 2
STROBE TYPE 3
STROBE TYPE 4
STROBE TYPE 5
STROBE TYPE 6
7| 5| CONTROL| 0-250
251-255| NO FUNCTION
RESET
8| 4| AURA DIMMER| 0-255| INTENSITY 0-100%
9| | AURA STROBE DURATION| 0-255| FLASH DURATION 7-650 MS
10| | AURA STROBE RATE| 0-255| FLASH RATE 0.289- 16.67 Hz
11| | AURA STROBE SELECTION| 0-5
6-42
43-85
86-128
129-171
172-214
215-255| NO STROBE
STROBE TYPE 1
STROBE TYPE 2
STROBE TYPE 3
STROBE TYPE 4
STROBE TYPE 5
STROBE TYPE 6
12| | AURA RED| 0-255| RED INTENSITY
13| | AURA gREEN| 0-255| gREEN INTENSITY
14| | AURA BLUE| 0-255| BLUE INTENSITY
| 15| | FX CROSS| 0-255| CROSSFADE FAST-SLOW
FIXTURE MODE| FUNCTION| DMX VALUE| DETAILS
---|---|---|---
14| 23| 68| 5-NET (ARTNET ONLY)
| 16| | AURA SHAPE SPEED| 0-255| SLOW-FAST
| 17| | AURA SHAPE SELECTION| 0
1-5
6-10
11-20
21-30
31-40
41-50
51-60
61-70
71-80
81-90
91-100
101-110
111-120
121-130
131-140
141-150
151-160
161-170
171-180
181-190
191-200
201-210
211-220
221-230
231-240
241-250
251-255| NO SHAPE BACKgROUND COLOR RgB FADE
RgB CHASE
SHAPE 1
SHAPE 2
SHAPE 3
SHAPE 4
MACRO 1
MACRO 2
MACRO 3
MACRO 4
MACRO 5
MACRO 6
MACRO 7
MACRO 8
MACRO 9
MACRO 10
MACRO 11
MACRO 12
MACRO 13
MACRO 14
MACRO 15
MACRO 16
MACRO 17
MACRO 18
MACRO 19
MACRO 20
| 18| | STROBE BEAM SHAPE SPEED| 0-255| SLOW-FAST
| 19| | STROBE BEAM SHAPE SELECTION| 0-5
6-30
31-50
51-70
71-90
91-110
111-130
131-150
151-170
171-190
191-210
211-230
231-255| NO SHAPE
MACRO 1
MACRO 2
MACRO 3
MACRO 4
MACRO 5
MACRO 6
MACRO 7
MACRO 8
MACRO 9
MACRO 10
MACRO 11
MACRO 12
| 20| | AURA BACKgROUND DIMMER| | INTENSITY 0-100%
| 21| | | AURA BACKgROUND RED| | BACKgROUND RED INTENSITY
FIXTURE MODE| FUNCTION| DMX VALUE| DETAILS
---|---|---|---
14| 23| 68| 5-NET (ARTNET ONLY)
| 22| | | AURA BACKgROUND gREEN| | BACKgROUND gREEN

INTENSITY

| 23| | | AURA BACKgROUND BLUE| | BACKgROUND BLUE INTEN- SITY
| 21
22
23| (1)
(2)
(3)| AURA PIXEL 1 RED AURA PIXEL 1 gREEN AURA PIXEL 1 BLUE| 0-255
0-255
0-255| AURA SINgLE PIXEL CONTROL
| 24
25
26| (4)
(5)
(6)| AURA PIXEL 2 RED AURA PIXEL 2 gREEN AURA PIXEL 2 BLUE|
| …| …|
| 54
55
56| (34)
(35)
(36)| AURA PIXEL 12 RED AURA PIXEL 12 gREEN AURA PIXEL 12 BLUE|
| 57| ((1))| STROBE BEAM PIXEL 1| | STROBE BEAM SINgLE PIXEL CONTROL
| 58| ((2))| STROBE BEAM PIXEL 2|
| …| …|
*| 68| ((12))| STROBE BEAM PIXEL 12|

5-NET MODE WORKS ONLY WITH ART-NET PROTOCOL, AND ONLY WITH CONNECTION THRU RJ-45 CABLE YOU HAVE TO SET IP ADRESS, SUBNET mask, UNIVERSEs To RECIVE SIGNAL
CONTROL – THERE ts TILT, MASTER BEAM vimmer, MASTER AURA pbimmer, RESET
LED – pixeL MAPPING BEAM anp AURA
ATTENTION artNET COUNTS UNIVERSES FROM O
TO PATCH IT CORRECTLY, YOU NEED TO OCCUPY 3 UNIVERSES. ONE FOR MAIN CONTROL, WHERE THE ADDRESS SET IN THE DEVICE APPLIES. THE OTHER TWO ARE UNIVERSE LED X AND X+1. THE ADDRESS FOR PIXEL MAPPING ALWAYS STARTS WITH 1.
EX. YOU SET MAIN CONTROL on universe 4, ADDRESS 201, LED on universe 10, So… YOU HAVE TO PATCH CONSOLE CONTROL at universe 5.201, BEAM at universe 10.1, AND AURA AT UNIVERSE 11.1

MENU OVERVIEW

DRAWINGS

PHOTOMETRICS

SPECIFICATION

• Light Source:
• 12 RGB sections (588 pcs RGB LED diode 5050),
• 12 WHITE BEAM sections (144 pcs. WHITE LED diode 3535 6000K)
• Power consumption: 1000W
• Power supply voltage: 110-240V, 50/60Hz AC
• TILT range: 185°
• RGB SECTION pixel and shapes control
• WHITE BEAM pixel and shapes control
• Operating modes: DMX 512, RDM, Art-Net, Auto-running, Master/Salve
• DMX channel mode: 14/23/68/5-net
• IP Rating: IP65
• Housing made: ABS
• Cooling: Passive
• AC IN/OUT: PowerCon TRUE1
• 3-Pin XLR DMX Input/Output
• Ethercon Input/Output
• Net Weight: 11,2 kg
• Dimensions: H(32.6)xW(13.7)xD(50.2) cm

FLASH-BUTRYM SP.J.
SKARBIMIERZYCE 18
72-002 DOLUJE
POLAND
WWW.FLASH-BUTRYM.PL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>