hp P008M Wireless Mouse User Manual
- June 16, 2024
- HP
Table of Contents
P008M Wireless Mouse
User Manual
Product Notices
Regulatory Notices
This document provides country- and region-specific non-wireless and wireless
regulatory notices and compliance information for your product. Some of these
notices may not apply to your product.
Federal Communications Commission notice
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio or television technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
For questions regarding this product, write to HP Inc.
1501 Page Mill Road Palo Alto, CA 94304 email
techregshelp@hp.com, or call HP at
650-857-1501.
To identify your product, refer to the part, series, or model number located
on the product.
Modifications
The FCC requires the user to be notified that any changes or modifications
made to this device that are not expressly approved by HP may void the user’s
authority to operate the equipment.
Cables
To maintain compliance with FCC Rules and Regulations, connections to this
device must be made with shielded cables having metallic RFI/EMI connector
hoods.
Products with wireless LAN devices or HP Mobile Broadband
Modules
This device must not be co-located or operating in conjunction with any other
antenna or transmitter.
WARNING: Exposure to Radio Frequency Radiation
The radiated output power of this device is below the FCC/Industry Canada
radio frequency exposure limits. Nevertheless, the device should be used in
such a manner that the potential for human contact is minimized during normal
operation. During normal operation of devices with displays equal to or less
than 30.5 cm (12 inches): To avoid the possibility of exceeding the
FCC/Industry Canada radio frequency exposure limits, human proximity to the
antennas should not be less than 2.5 cm (1 inch). To identify the location of
the wireless antennas, refer to the user guides included with your device.
During normal operation of devices with displays greater than 30.5 cm (12
inches): To avoid the possibility of exceeding the FCC/Industry Canada radio
frequency exposure limits, human proximity to the antennas should not be less
than 20 cm (8 inches), including when the device display is closed. To
identify the location of the wireless antennas, refer to the user guides
included with your device.
CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted
to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range.
FCC/Industry Canada requires this product to be used indoors for the frequency
range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference
to co-channel mobile satellite systems. High-power radar is allocated as the
primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar
stations can cause interference with and/or damage to this device. The
antennas for this device are not replaceable. Any attempt at user access will
damage your device.
Declaration of Conformity
Products bearing the CE marking and UK marking comply with one or more of the
following EU Directives and the applicable UK Statutory Instruments as may be
applicable:
RED 2014/53/EU; Low Voltage Directive 2014/35/EU; EMC Directive 2014/30/EU;
Ecodesign Directive 2009/125/EC; RoHS Directive 2011/65/EU. Compliance with
these directives is assessed using applicable European Harmonised Standards.
Radio frequency bands and maximum power levels (select products only)
RadioTechnology | Maximum Transmit Power EIRP (mW) |
---|
WLAN/Bluetooth: 2.4 GHz
WLAN: 5 GHz| 100
WLAN: 6 GHz (LPI/VLP)| 200/25
NFC: 13.56 MHz| 10
Non-specific Short Range Device: 2.4 GHz| 10
Note: Use only HP-supported software drivers and correct country settings
to ensure compliance.
The point of contact for EU regulatory matters is HP Deutschland GmbH, HQ-TRE,
71025, Boeblingen, Germany.
The point of contact for UK regulatory matters is HP Inc UK Ltd, Regulatory
Enquiries, Earley West, 300 Thames Valley Park Drive, Reading, RG6 1PT, UK.
AT| BE| BG| CY| CZ
DE| DK| EE| EL| ES
Fl| FR| HR| HU| IE
IT| LT| LU| LV| MT
NL| PL| PT| RO| SE
SI| SK| IS| LI| NO
CH| TR| UK(NI)|
AL| BA| MD| ME| MK
RS| UK| XK| |
IMPORTANT: IEEE 802.11x wireless LAN with 5150–5350 MHz and/or 5945–6425* MHz frequency band is restricted for indoor use only in all countries reflected in the matrix. Using this WLAN application(s) outdoors might lead to interference issues with existing radio services.
-
Selected products only may use 5925–6425 MHz for UK setup.
HP Inc.
Адрес: 1501 Page Mill Road, Palo Alto, California 94304, U.S.
Singapore wireless notice
Turn off any WWAN devices while you are onboard aircraft. The use of these devices onboard aircraft is illegal, may be dangerous to the operation of the aircraft, and may disrupt the cellular network.
Failure to observe this instruction may lead to suspension or denial of cellular services to the offender, or legal action, or both.
Users are reminded to restrict the use of radio equipment in fuel depots, chemical plants, and where blasting operations are in progress.
As with other mobile radio transmitting equipment, users are advised that for satisfactory operation of the equipment and for the safety of personnel, no part of the human body should be allowed to come too close to the antennas during operation of the equipment.
This device has been designed to comply with applicable requirements for exposure to radio waves, based on scientific guidelines that include margins intended to assure the safety of all people, regardless of health and age. These radio wave exposure guidelines employ a unit of measurement known as the specific absorption rate (SAR). Tests for SAR are conducted using standardized methods, with the phone transmitting at its highest certified power level in all used frequency bands.The SAR data information is based on CENELEC’s standards
EN50360 and EN50361, which use the limit of 2 watts per kilogram, averaged over 10 grams of tissue.
Thailand WWAN wireless notice
This telecommunication equipment conforms to the requirements of NBTC.
Laser compliance
Some products may contain a laser that is classified as a Class 1 Laser Product in accordance with US FDA regulations and the IEC 60825-1.
Each laser product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 or Laser Notice No. 56, dated May 8, 2019; and with IEC 60825-1:2007.
WARNING! Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product’s installation guide may result in hazardous radiation exposure.
To reduce the risk of exposure to hazardous radiation:- Do not try to open the module enclosure. There are no user-serviceable components inside.
- Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein.
- Allow only HP Authorized service technicians to repair the unit.
Power cord notice
If you were not provided with a power cord for the computer or for an external
power accessory intended for use with the computer, you should purchase a
power cord that is approved for use in your country or region.
The power cord must be rated for the product and for the voltage and current
marked on the product’s electrical ratings label. The voltage and current
rating of the cord should be greater than the voltage and current rating
marked on the product. In addition, the diameter of the wire must be a minimum
of 0.75 mm²/18AWG, and the length of the cord must be between 1.0 m (3.2 ft)
and 2 m (6.56 ft). If you have questions about the type of power cord to use,
contact your authorized service provider.
A power cord should be routed so that it is not likely to be walked on or
pinched by items placed upon it or against it. Particular attention should be
paid to the plug, electrical outlet, and the point where the cord exits from
the product.
Safety Notices
WARNING! Do not allow the AC adapter to contact the skin or a soft
surface, such as pillows or rugs or clothing, during operation. The AC adapter
complies with the user-accessible surface temperature limits defined by
applicable safety standards.
WARNING! To reduce the risk of electric shock or damage to the equipment:
- Plug the AC adapter into an AC outlet that is easily accessible at all times.
- If the power cord has a 3-pin attachment head, plug the cord into a grounded (earthed) 3-pin outlet.
Headset and earphone volume level notice
To prevent possible hearing damage, do not use high volume levels for long
periods. Before using a headset or earphones, always reset the volume to a low
level.
For your own safety, use headsets or earphones compliant with the headphone
limits in EN 50332-2.
When the HP product includes a headset or earphones, the combination is in
compliance to EN 50332-1.
Environmental notices
Disposal of waste equipment by users
This symbol means do not dispose of your product with your other household
waste. Instead, you should protect human health and the environment by handing
over your waste equipment to a designated collection point for the recycling
of waste electrical and electronic equipment. For more information, please
contact your household waste disposal service or go to
http://www.hp.com/recycle.
Battery Section
When a battery has reached the end of its useful life, do not dispose of the
battery in general household waste. Follow the local laws and regulations in
your area for computer battery disposal.
HP encourages customers to recycle used electronic hardware, HP original print
cartridges packaging, and rechargeable batteries. For more information about
recycling programs, refer to the HP website at http://www.hp.com/recycle.
For information about removing a user-replaceable battery, refer to the user
guide included with the product.
WARNING! Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
WARNING! To reduce the risk of fire or burns, do not disassemble, crush,
or puncture; do not short external contacts; do not dispose of in fire or
water.
WARNING! Keep the battery away from children.
WARNING! To reduce potential safety issues, only the battery provided
with the computer, a replacement battery provided by HP, or a compatible
battery purchased as an accessory from HP should be used with the computer.
WARNING! A battery subjected to extremely high temperatures in the
surrounding environment or extremely low air pressure may result in explosion
or leakage of flammable liquid or gas.
Chemical substances
HP is committed to providing our customers with information about the chemical
substances in our products as needed to comply with legal requirements such as
REACH (Regulation EC No1907/2006 of the European Parliament and the Council).
A chemical information report for this product can be found at
http://www.hp.com/go/reach.
Taiwan Declaration of the Presence Condition of the Restricted Substances
Marking
#1 Group of products: Accessories that have lens function
Camera, digital video camera, automotive video camera
Restricted substances and their chemical symbols
Unit| (Pb)| (Hg)| (Cd)| (Cr6)| (P88)|
(PUDE)
Circuit board| | 0| 0| 0| 0| 0
Shell| 0| 0| 0| 0| 0| 0
Metal part| —| 0| 0| 0| 0| 0
Lens| 0| 0| —| 0| 0| 0
Input/output device| —| 0| 0| 0| 0| 0
Light-sensing component| —| 0| 0| 0| 0| 0
Cable| —| 0| 0| 0| 0| 0
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the
percentage content of the restricted substance exceeds the reference
percentage value of presence condition.
Note 2: “ ” indicates that the percentage content of the restricted substance
does not exceed the percentage of reference value of presence.
Note 3: “—” indicates that the restricted substance corresponds to the
exemption.
#2 Group of products: Accessories that have speaker function
Speakers, headphones, headsets, earphones, earbuds
Restricted substances and their chemical symbols
Unit| (Pb)| (Hg)| (Cd)| (Cr 6)| (PBS)| (ME)
Circuit board| | 0| 0| 0| 0| 0
Shell| 0| 0| 0| 0| 0| 0
Metal part| —| 0| 0| 0| 0| 0
Speaker| —| 0| 0| 0| 0| 0
Cable| —| 0| 0| 0| 0| 0
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the
percentage content of the restricted substance exceeds the reference
percentage value of presence condition.
Note 2: “ ” indicates that the percentage content of the restricted substance
does not exceed the percentage of reference value of presence.
Note 3: “—” indicates that the restricted substance corresponds to the
exemption.
#5 Group of products: Other accessories that do not have an outstanding
function
Mouse, keyboard, power supply, battery charger, wireless video module,
video ingest module, wireless charger, cable kit
Restricted substances and their chemical symbols
Unit| (Pb)| (Hg)| (Cd)| (cr6)| (PBB)|
(PBDE)
Circuit board| —| 0| 0| 0| 0| 0
Shell| 0| 0| 0| 0| 0| 0
Metal part| —| 0| 0| 0| 0| 0
Cable| —| 0| 0| 0| 0| 0
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the
percentage content of the restricted substance exceeds the reference
percentage value of presence condition.
Note 2: “ ” indicates that the percentage content of the restricted substance
does not exceed the percentage of reference value of presence.
Note 3: “—” indicates that the restricted substance corresponds to the
exemption.
#3 Group of products: Accessories that have read/write function
CD/DVD/Floppy device, storage device (external HDD/SSD, USB flash drive),
docking device, card reader, writing device (stylus, pen), one-to-multiple
hub, touch mat, magnetic stripe reader, barcode scanner, fingerprint reader,
port replicator/ USB hub
Restricted substances and their chemical symbols
Unit| (Pb)| (Hg)| (Cd)| (Cr”)| (PBB)|
(PBDE)
Circuit board| —| 0| 0| 0| 0| 0
Shed| 0| 0| 0| 0| 0| 0
Metal part| —| 0| 0| 0| 0| 0
Read/write component| —| 0| 0| 0| 0| 0
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the
percentage content of the restricted substance exceeds the reference
percentage value of presence condition.
Note 2: “ ” indicates that the percentage content of the restricted substance
does not exceed the percentage of reference value of presence.
Note 3: “—” indicates that the restricted substance corresponds to the
exemption.
#6 Group of products: Other printer products
Thermal receipt printer
Restricted substances and their chemical symbols
Unit| (Pb)| (Hg)| (Cd)| (Cr’)| (PBB)|
(PBDE)
Circuit board| —| 0| 0| 0| 0| 0
Shell| 0| 0| 0| 0| 0| 0
Metal part| —| 0| 0| 0| 0| 0
0
Print head| —| 0| 0| 0| 0
Motor| —| 0| 0| 0| 0| 0
Paper roller| —| 0| 0| 0| 0| 0
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the
percentage content of the restricted substance exceeds the reference
percentage value of presence condition.
Note 2: “ ” indicates that the percentage content of the restricted substance
does not exceed the percentage of reference value of presence.
Note 3: “—” indicates that the restricted substance corresponds to the
exemption.
#4 Group of products: Accessories that have PCB as main part
Memory card, network card, graphic card, and other internal add-on cards
Restricted substances and their chemical symbols
Unit| (Pb)| (Hg)| (Cd)| (Cr’)| (PBB)|
(PBDE)
Circuit board| —| 0| 0| 0| 0| 0
Active component (transistors and integrated circuits)| —| 0| 0| 0| 0| 0
Passive component (resistors and capacitors)| —| 0| 0| 0| 0| 0
Solder| —| 0| 0| 0| 0| 0
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the
percentage content of the restricted substance exceeds the reference
percentage value of presence condition.
Note 2: “ ” indicates that the percentage content of the restricted substance
does not exceed the percentage of reference value of presence.
Note 3: “—” indicates that the restricted substance corresponds to the
exemption.
7 Group of products : VR (Virtual reality products) monitors (including head-
mounted monitors) / Retail Point of Sale monitors
Restricted substances and their chemical symbols
Unit| (Pb)| (Hg)| (Cd)| (Cr6)| (PBB)|
(PBDE)
Circuit board| —| 0| 0| 0| 0| 0
Shell| 0| 0| 0| 0| 0| 0
Metal part| —| 0
0| 0| 0| 0| 0
Lens| 0| —| 0| 0| 0
Input/output device| —| 0| 0| 0| 0| 0
Light-sensing component| —| 0| 0| 0| 0| 0
Cable| —| 0| 0| 0| 0| 0
Liquid Crystal Display (LCD) Panel| —| 0| 0| 0| 0| 0
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the
percentage content of the restricted substance exceeds the reference
percentage value of presence condition.
Note 2: “ ” indicates that the percentage content of the restricted substance
does not exceed the percentage of reference value of presence.
Note 3: “—” indicates that the restricted substance corresponds to the
exemption.
India restriction of hazardous substances (RoHS)
This product, as well as its related consumables and spares, complies with the
reduction in hazardous substances provisions of the “India E-waste Rule 2016.”
It does not contain lead, mercury, hexavalent chromium, polybrominated
biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1
weight % and 0.01 weight % for cadmium, except where allowed pursuant to the
exemptions set in Schedule 2 of the Rule.
Information for European Union Commission Regulation 1275/2008
To locate product power consumption data, including when the product is in
networked standby with all wired network ports connected and wireless devices
connected, refer to section P14 “Additional information” of the product IT ECO
Declaration at
http://www.hp.com/hpinfo/globalcitizenship/environment/productdata
/itecodesktop-pc.html.
Where applicable, activate and deactivate a wireless network using the
instructions included in the product user guide or the operating system.
Information is also available at http://www.hp.com/support.
Packaging labelling and sorting information – Italy Background
The Legislative Decree no. 116 of 3 September 2020 requires that all packaging
be “appropriately labelled according to the procedures established by the
applicable UNI technical standards and in accordance with the determinations
adopted by the Commission of the European Union to facilitate the collection,
reuse, recovery and recycling of packaging, as well as to give correct
information to consumers on the final destination of packaging. Producers
shall also be obliged to indicate, for the purposes of identifying and
classifying the packaging, the nature of the packaging materials used, on the
basis of Commission Decision 97/129/EC.”
Coding of the packaging material
HP indicates the alphanumeric coding required by Decision 97/129/EC by marking
all its packaging (primary, secondary and tertiary) with the appropriate
material code.
Consumer information on the final destination of packaging
HP provides the following table to enable consumers to correctly identify the
appropriate collection stream for packaging waste:
Packaging Material| Material coding (visible on the packaging)|
Recycling Collection Stream
---|---|---
Polyethylene Terephthalate (PET)| | Plastic
High Density Polyethylene (HDPE)| Plastic
Low Density Polyethylene (LDPE)| Plastic
Polypropylene (PP)| Plastic
Polystyrene| Plastic
Other Plastic Resins| Plastic
Corrugated fiberboard| Paper
Noncorrugated fiberboard| Paper
Paper| Paper
Composite Paper & Plastic| Other
© Copyright 2015-2022 HP Development Company, L.P.
Bluetooth is a trademark owned by its proprietor and used by HP Inc. under
license. Java is a registered trademark of Oracle and/or its affiliates.
The information contained herein is subject to change without notice. The only
warranties for HP products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should be
construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
Sixteenth Edition: December 2022 First Edition: August 2015
References
- Anatel — Agência Nacional de Telecomunicações
- Reciclagem dos suprimentos HP | HP® Brasil
- HP Planet Partners 助力循环经济发展 | 中国惠普
- Laptop Computers, Desktops, Printers, Ink & Toner | HP® Official Site
- Product Return and Recycling | HP® Official Site
- Hewlett-Packard Labor Condition Applications
- hp.com/hpinfo/globalcitizenship/
- Product Return and Recycling | HP® Official Site
- hp.com/support
- MT-Tech Cloud (EX)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>