MOUNTUP MU0016-25 Tilting TV Wall Mount Installation Guide
- June 16, 2024
- MOUNTUP
Table of Contents
- Safety Caution
- Verify Your Wall Construction
- Product Dimensions
- Supplied Parts and Hardware
- Extra Tools You Need (Not Supplied)
- Attach Brackets to TV
- Assemble the Mount
- Attach Wall Plate to Wall
- Attach Wall Plate to Wall
- Hang and Secure TV to Wall Plate
- Cable Management (If necessary)
- Documents / Resources
**MOUNTUP MU0016-25 Tilting TV Wall Mount Installation Guide
**
Safety Caution
Please read this instruction carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.
- This product is designed for use in wood stud or solid concrete wall.
- DO NOT install into drywall alone.
- The wall must be capable of supporting five times the weight of the TV and mount combined.
- Incorrect installation may result in product damage / property damage or body injury. We shall bear no responsibility for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; please contact our customer service team. Never use damaged parts!
Must Check Before Getting Started
Minimum VESA Pattern (W × H): 100mm × 100mm / 4 in × 4 in
Maximum VESA Pattern (W × H): 600mm × 400mm / 24 in × 16 in
WARNING
DO NOT exceed the maximum weight indicated. This mounting system is
intended for use only within the maximum weights indicated. Use with products
heavier than the maximum weights indicated may result in failure of the mount
and its accessories, causing possible damage or injury.
MAX: 120 lbs (54.5 kg)
Verify Your Wall Construction
CAUTION:
Avoid potential personal injuries and property damage! Drywall covering the
wall must not exceed 5/8 in. (16 mm). Minimum wood stud size: nominal 2 x 4
in. (51 x 102 mm) actual 1 ½ x 3 ½ in. (38 x 89 mm).
CAUTION:
Avoid potential personal injuries and property damage! Mount the wall plate
assembly directly onto the concrete surface (no surface covering).
CAUTION:
DO NOT install into drywall alone.
Product Dimensions
Supplied Parts and Hardware
-
Wall Plate H x2
-
Connection Plate K x1
-
TV Brackets J x1
Wall / Product
-
Lag Bolt ST8x65mm A x4
-
Washer M8 B x4
-
wrench M5×8mm C x8
-
Allen key 4mm F x1
TV
-
Philips Screws
M4 x 12mm
M4 x 30mm
×4 ×4 MA -
Philips Screws
M6 x 15mm
M6 x 30mm
x4×4MB -
Philips Screws
M8 x 25mm
M8 x 45mm
×4 ×4MC -
Spacers
H10mm
×8MD -
Washers
Ф6mm
M4-5-6
×4 ME -
Spacers
H5mm
×8MF
Bubble Level T1 ×1
Velcro Cable Ties T2 ×3
NOTE: Not all parts and hardware included will be used.
Extra Tools You Need (Not Supplied)
Band Tape
Pencil
Electro drill
Socket Wrench
Screwdriver
Attach Brackets to TV
Select TV Screws
-
Too Short
-
Too Long
-
Not Vertical
-
Correct
-
Correct
Need Spacer?
Yes, choose the appropriate screws, washers, and spacers for your TV.
-
For more spacing between bracket and TV
-
For protruded back TV
-
For counterbore of TV
-
To avoid the blocked input
No, just choose the screws, washers.
Do not tighten the screws excessively or tighten them by using the Electro drill, or your TV might be damaged.
Assemble the Mount
**Tilt Adjustment
** Pull brackets to your desired angle then fasten 2 titing bolts with Allen key (F).
Option
To keep TV in vertical position, please use two M4 screws (MA) to insert the
holes on two brackets respectively.
**Assemble Wall Plate
**
Attach Wall Plate to Wall
OPTION A:
Wood Stud Installation
Locate your studs. Verify and mark the center of the stud by finding the stud edges using awl and stud finder.
Line up the holes with your stud center line. Level the wall plate and mark the pilot hole locations.
Drill pilot holes using a Ф7/32 in (Ф5.5mm) diameter drill bit.
IMPORTANT:
Do not drill holes into where water pipes or electrical wires are located. Be
sure to drill into the center of the stud.
Install wall plate using lag bolts with Socket Wrench, NO Electrod rill. No anchors when installed onto the wood studs.
CAUTION: Do not use in drywall or wood stud!
**** CAUTION:
To avoid potential personal injury or property damage:
All 4 lag bolts MUST BE firmly tightened to prevent unwanted movement of the
wall plate assembly. Ensure the wall plate assembly is securely fastened to
the wall before continuing on to the next step.
Attach Wall Plate to Wall
OPTION B:
Solid Concrete Wall Installation
Drill pilot holes using a Ф3/8 in (Ф10mm) diameter drill bit.
IMPORTANT:
Do not drill holes into where water pipes or electrical wires are located, or
mortar between blocks.
Use the hammer to knock anchors (not included) into the concrete wall. Be sure the anchors are seated flush with the concrete surface.
Install wall plate using lag bolts and anchors (not included) with Socket Wrench, NO Electrodrill.
CAUTION
To avoid potential personal injury or property damage:
All 4 lag bolts MUST BE firmly tightened to prevent unwanted movement of the
wall plate assembly. Ensure the wall plate assembly is securely fastened to
the wall before continuing on to the next step.
Hang and Secure TV to Wall Plate
Before hanging TV, please conduct “wall plate installation integrity test” first.
Hang and secure TV assembly onto the wall plate.
CAUTION:
Avoid potential personal injury or property damage! Always make sure your TV
brackets are in the locked position so the TV is securely attached to the wall
plate assembly
If necessary
Take down the TV from the Mount
To prevent breaking the locking latch:
always pull and hold the release straps down while pulling the TV away from
the wall.
Cable Management (If necessary)
Documents / Resources
|
MOUNTUP MU0016-25 Tilting TV Wall
Mount
[pdf] Installation Guide
MU0016-25, MU0016-25 Tilting TV Wall Mount, Tilting TV Wall Mount, TV Wall
Mount, Wall Mount, Mount
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>