MOUNTUP V2.0 Electric Height Adjustable Standing Desk Instruction Manual

June 16, 2024
MOUNTUP

MOUNTUP V2.0 Electric Height Adjustable Standing Desk

Product Information

Specifications

  • Maximum Height: 48 inches
  • Minimum Height: 29 1/8 inches
  • Weight Capacity: 176 lbs / 80 kg
  • Version: V2.0

Product Usage Instructions

Safety Instructions
Before assembly, please read and follow these safety instructions:

  • Keep children away from the desk and the controller.
  • Do not use the desk if you are under 18 years old.
  • Ensure proper electrical safety by connecting the desk to a grounded outlet.
  • Do not use the desk if it is damaged or not functioning properly.
  • Do not exceed the weight limit of the desk.
  • Keep the knee space clear of obstacles.
  • Balance the weight on the desk for correct operation and longer component life.
  • Leave enough slack in cables to allow for full range of vertical motion.

Package Contents

  • Screw & Bolt Kits

Assembly Steps – Installation Tips
Lay a mat or old blanket underneath the desk to protect the floor and furniture during assembly.

Step 1

  1. Insert Wooden Pin (K) into the holes of Tabletop (A-1 or A-2) and assemble them together.
  2. Align and attach Fixture (J) to the assembled tabletops. Tighten them with M6X14 Bolt (M-A) and Allen Key (M-E).

Step 2

  1. Attach Side Bracket (C) to Frame (B) with 4 pcs of M6x12 Bolt (M-C). Tighten them with Allen Key (M-E). Pay attention to the direction of Side Bracket (C).

Step 3

  1. Attach Base (D) on Frame (B). Use 8 pcs of M6x20 Bolt (M-B) and Allen Key (M-E) to tighten them.

Casters Installation (Optional)
Note: You can replace the leveling studs with four casters if preferred. Remove the pre-assembled leveling studs and save them for future use. Insert Caster with Lock (L) and use Wrench (M-F) to tighten them.

Step 4
Use Allen Key (M-E) to loosen the pre-assembled crossbar screws and loosen the plastic sleeves on the hexagon rod. Then adjust the length of Frame (B) to the limit position.

Step 5

  1. Place and align Frame (B) to the assembled tabletop (A) with 12 pcs of M6x14 bolt (M-A). Use Allen Key (M-E) to tighten them.
  2. Tighten the pre-assembled bolts on the crossbar with Allen Key (M-E).
  3. Tighten the plastic sleeves on the Hexagon Rod.
  4. Attach Hook (E) to the tabletop (A). Use Screw (M-D) and Screwdriver (M-H) to tighten them.

Step 6

  1. Put Controller (G) on the tabletop and align it with pilot holes. Use Screw (M-D) and Screwdriver (M-H) to tighten them.
  2. Align Power Adapter (F) with the pilot holes, and then tighten it with Screw (M-D) & Screwdriver (M-H).

Step 7

  1. Connect the motor wire to Controller (G).
  2. Connect the wire of the Power Adapter (F) to the Controller (G).
  3. Connect Power Wire (H) to Power Adapter (F).

FAQ

  • Q: What is the weight capacity of the desk?
    A: The weight capacity of the desk is 176 lbs / 80 kg.

  • Q: Can I replace the leveling studs with casters?
    A: Yes, you can replace the leveling studs with four casters. Please refer to the Casters Installation section for instructions.

  • Q: How do I adjust the height of the desk?
    A: Use the Controller (G) to adjust the height of the desk. Connect the motor wire, power adapter wire, and power wire according to the instructions in Step 7.

If you have any issues, please feel free to contact our customer support before returning. At MOUNTUP strive to provide you with the best quality products and services in the industry.

SAFETY INSTRUCTIONS

BEFORE ASSEMBLY

  • Place the product on a flat floor with a mat to avoid scratches.
  • Layout all components and hardware. Check all parts are included and undamaged.
  • Should anybody intends to install or use this electric height adjustable desk, please read and understand this manual carefully.

WARNING

  • Do not open or modify any components, including the legs, system control box or adjustment controller. This might cause electric shock or permanent damage to the product.
  • This product contains small items that could be a choking hazard if swallowed. KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
  • Neither adults nor children can sit or stand on the desk. Do not play within the area under the desk.
  • This might cause to severe bodily injury.
  • If you do not understand these instructions or have any doubt about the safety instructions, assembly or use of this product, please contact our customer service.
  • At least two adults are required to assemble this desk.

USE & LIABILITY

  • Do not use this product for any purpose that is not explicitly specified in this manual.
  • Do not exceed weight capacity of 176LBS / 80KG.
  • Indoor use only.
  • We cannot be liable for damage or injury caused by incorrect assembly or inappropriate use.

ELECTRICAL SAFETY
This product is powered by electricity. To avoid burns, fire and electric shock, please read the following instructions carefully.

  • The product must be connected to AC 100-240 Voltage power supply.
  • To avoid electric failure, please keep this desk and parts dry from water or humid environments.

WARNING-PINCH POINT
DO NOT place hands on or near any parts underneath the desk. Moving parts can crush and cut. Pinch points are created during lifting and lowering the worksurface. Failure to follow these instructions may result in serious personal injury.

Failure to follow these instructions may result in property damage and/or personal injury.

PACKAGE CONTENTS

SCREW & BOLT KITS

ASSEMBLY STEPS

Installation Tips

STEP 1

  1. Insert Wooden Pin (K) into the holes of Tabletop (A-1 or A-2) and assemble them together.
  2. Align and attach Fixture (J) to the assembled tabletops. Tighten them with M6X14 Bolt (M-A) and Allen Key (M-E).

STEP 2
Attach Side Bracket (C) to Frame (B) with 4 pcs of M6x12 Bolt (M-C). Tighten them with Allen Key (M-E).

STEP 3
Attach Base (D) on Frame (B). Use 8 pcs of M6x20 Bolt (M-B) and Allen Key (M-E) to tighten them.

Caters Installation (Optional)
Note: As you prefer, you can replace the leveling studs with four casters.
Remove the pre-assembled leveling studs and save them for future use. Insert Caster with Lock (L) and use Wrench (M-F) to tighten them.

STEP 4
Use Allen Key (M-E) to loose the pre-assembled crossbar screws and loose the plastic sleeves on hexagon rod. Then adjust the length of Frame (B) to the limit position.

STEP 5
Note:
It’s highly suggested not to tighten the bolts one by one, instead, align them firstly and then tighten when they are all aligned well.

STEP 6

  1. Put Controller (G) on the tabletop and align it with pilot holes. Use Screw (M-D) and Screwdriver (M-H) to tighten them.
  2. Align Power Adapter (F) with the pilot holes, and then tighten it with Screw (M-D) & Screwdriver (M-H).

STEP 7

  1. Connect the motor wire to Controller (G).
  2. Connect the wire of Power Adapter (F) to the Controller (G).
  3. Connect Power Wire (H) to Power Adapter (F).

STEP 8
Attach Cable Clip (M-G) to the backside of the assembled tabletop for cable management.

STEP 9

  1. Turn over the desk to stay upwards and insert Grommet (I).
  2. Make sure the legs are level and all bolts are well tightened to avoid the desk making noise or wobbling.
  3. Plu in the ower su l and et the desk ower on.

Operation Guide

Set Anti-collision Sensitivity
The anti-collision sensitivity of the desk defaults to 2. If you need to set the sensitivity, please do the following steps.

  • Press and hold “1” and “2” for more than 20 seconds, until the controller screen flashes, and the system can start setting.
  • Press button “1” and “2” simultaneously, and you can select the menu: U-0 and d-0.
    • U -o means upward anti-collision sensitivity.
    • d -o means downward anti-collision sensitivity.
  • Press “^” or “v” can adjust the number from 0-9 (0 means no sensitivity, 9 means the highest sensitivity).’
  • Press and hold “1” and “2” for 5 seconds, when the screen shows , the modified content is saved.

Product Dimensions

Technical Specifications

  • Lowest Height: 29 1/8in (74cm)
  • Highest Height: 48in (122cm)
  • Weight Capacity: 176 lbs (80Kg)
  • Tabletop Size: 55 1/8in x 27 1/2in x 5 /8in 140cm x 70cm x 1.5cm
  • Input Voltage: AC 100-240V
  • Travel Speed: 25mm/s
  • Applicable Temperature: 0-40°C
  • Noise:  ≤50 dB

Technical Support: 626-425-4350, Mon-Fri, 10am-6pm (PST)
Other Info: help@jollyholding.com
Website: https://mountup.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals