Telink TLSR9518A Dongle Generic Starter Kit User Guide
- June 16, 2024
- TELINK
Table of Contents
Telink TLSR9518A Dongle Generic Starter Kit
Product Information
Specifications
- Model : TLSR9518A Dongle
- Supported Standards : Low Energy (LE), Indoor Positioning
- Features : High quality wearable device
- Package Material List : TLSRSOCSG80R-V1 Burning EVK for TLSR9518A, Dupontline
Product Usage Instructions
Product Introduction
The TLSR9518A Dongle is designed to support standards and industrial alliance specifications for low energy (LE) and indoor positioning. It combines the features and functions required for high-quality wearable devices into a single System-on-Chip (SoC).
General Introduction
The TLSR9518A supports standards and industrial alliance specifications for low energy (LE) and indoor positioning.
Material List
The package includes:
- TLSRSOCSG80R-V1 Burning EVK for TLSR9518A
- Dupontline
Core Board Introduction
Dongle Introduction
The TLSR9518A Dongle supports standards and industrial alliance specifications for low energy (LE) and indoor positioning. It combines the features and functions required for high-quality wearable devices into a single System-on- Chip (SoC).
POWER and SWS Connection
The POWER and SWS connections are as follows:
| 3V3 | GND | SWM |
|---|---|---|
| 3V3 | GND | SWS |
FAQ
Q: What standards does the TLSR9518A Dongle support?
A: The TLSR9518A Dongle supports low energy (LE) and indoor positioning standards.
Q: What features does the TLSR9518A Dongle have?
A : The TLSR9518A Dongle combines the features and functions required for high-quality wearable devices into a single System-on-Chip (SoC).
Q: What is included in the package?
A : The package includes the TLSRSOCSG80R-V1 Burning EVK for TLSR9518A and a Dupontline.
Product introduction
General introduction
The TLSR9518A supports standards and industrial alliance , low energy (LE),
indoor positioning
TheTLSR9518Acombinesthefeaturesandfunctionsneededforhighqualitywearable.
Package Materiallist
TLSRSOCSG80R-V1
Burning EVKfor TLSR9518A，Including the Dupontline
Product Introduction – Continued
Material List – continued
Core Board Introduction
Dongle introduction
- The TLSR9518A supports standards and industrial alliance specifications , low energy (LE), indoor positioning, The TLSR9518A combines the features and functions needed for high quality wearable devices into a single System-on-Chip (SoC)2.
- The core board has the following characteristicsClock source of 24 MHz & 32.768 Hz Crystal and 32 kHz / 24 MHz embedd ed RC oscillator, among which the externa24MHz crystal is to calibrate internal 32 kHz clock, the internal 32 kHz oscillator is f or low precision application, the externa32.768 kHz crystal is for high precision application Up to 48 GPIOs. All digital 10s can be used as GPIOS.Configurable toselect 2-wire SDP or 4-wire JTAG debug interface SPI/12C/UART with hardware flow contro l and 7816 protocol support
- This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:
- Reorient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Core Board Introduction – Continued
POWER and SWS connection
3V3 / 3V3
GND / GND
SWM / SWS
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>