Frank V098 Display Cooler Instruction Manual

Frank V098 Display Cooler

Product Information

Specifications

• Model: V098
• Climatic class: N
• Storage Temperature (°C): 0-10
• Anti-shock protection class: 1.2
• Capacity (L): 98
• Rated Voltage (V): 220-240V
• Rated Frequency (Hz): 50Hz
• LAMP max power (W): 10
• Refrigerant/Charging (g): R600a/40

Product Usage Instructions

Portage and Storage

Before using the display cooler, remove the carton and packing foam, including the bottom foam. Clean the unit thoroughly. Adjust the foot to make the unit steady according to the ground. After moving the unit, let it sit for 30 minutes before switching it on. Keep the unit empty for one hour after connecting the power.

Setting and Adjustment of Temperature

The display cooler is equipped with a thermostat knob for temperature control. The knob has an “on/off” position and a scale. Before using, check if the scale is on an appropriate position. Normally, in summer when the ambient temperature is high, turn theknob anti-clockwise to position 2. In winter when the ambient temperature is low, turn the knob clockwise to position 4. Position 0 represents stop running.

Storage of Articles

When storing articles in the display cooler, avoid putting a large amount of items into the unit at one time. Leave some space around the foodstuff to allow for proper airflow. Keep bottled articles away from the walls of the interior cabinet to prevent freezing and breakage. Additionally, do not put warm food directly into the unit. Allow the food to cool to normal temperature before placing it in the display cooler. This will help lower energy consumption and prolong the service life of the compressor.

FAQ

• Problem: The unit is not level
  Possible Cause: The adjustable foots are not properly adjusted.
  Solution: Adjust the adjustable foots to level the unit.

• Problem: Too high noise, lamp is not on
  Possible Cause: The fastener of the unit is loose or the pipes are touching.
  Solution: Fasten the loose fastener and carefully separate the touched compressor pipes. Replace the lamp if it is burned out.

• Problem: Abnormal operation of the compressor or buzz sound
  Possible Cause: The power voltage is out of the rated range.
  Solution: Disconnect the power supply immediately and reconnect it with normal voltage. Consider using a voltage stabilizer if the power supply is poor.

• Problem: Compressor operates too long time and no frost on the surface of inner cabinet
  Possible Cause: The refrigeration system is at fault (leakage or blocked).
  Solution: Send the unit to the service department for repair.

• Problem: There is frost or ice on the evaporator of the inner cabinet and too low internal temperature, the compressor operates never stop
  Possible Cause: The thermostat does not work.
  Solution: Ask the service department for repair.

• Problem: Bad heat dissipation and ventilation of casing, the ambient temperature is too high, the internal temperature is too high, too much warm food was put in at one time
  Solution: Improve ventilation and lower the ambient temperature. Take out some food.

Caution : Dismantling the unit by non-professional staff is prohibited, it will cause hazard.

Please read this manual carefully, and make sureto keep this manual in the place accessible by theuser at any time.

Structural diagram

Specifications

The above specifications are subject to improvements

Caution : Dismantling the unit by non-professional staff is prohibited, it will cause hazard.

Safety Cautions

1. This unit uses AC220V/50Hz power, there should be a 500va stabilizer if the voltage fluctuation exceed AC198V～242V
2. The user should hold the plug when the power is on/off, dragging or pulling the power cord is prohibited.
3. Do not remove the power cord or plug
4. Must use dependent socket and reliable ground wire. Ground wire must not connect with the null line of the gas pipe, warm gas pipe, water pipe and must be single power
5. Never splash water on the unit directly.
6. Keep away from explosive, hazardous goods such as ether, gas, alcohol, bonding agents, gunpowder etc.
7. Keep away from spray of inflammables such as paints, coating materials etc.
8. After the unit is switched off, it should not be restarted within 5 minutes.
9. Do not leave the power cord under any heavy objects including the unit itself.
10. Do not drill holes or install other objects on the casing.
11. This cooler is not suitable for storage pharmaceutical products.

Portage and storage

1. Keep the unit vertical when carrying the unit, the angle to the horizontal line should not be over 50 °，otherwise it will damage the compressor and affect normal operation of the unit.
2. The unit should be place on a solid and firm ground, take away the bottom pack to lower the shock and noise.
3. Leave at least 20 cm of distance between the back of the unit and the wall for ventilation and leave a space with an open angle of 160 ° for the door.
4. Keep the unit away from heat sources and avoiding direct sunlight.
5. Never place the unit on a location where water can reach or with high moisture. Splashed water and dirt should be wiped off in time by usinga soft cloth.
6. Do not place the unit in the environment cold enough to be iced.

Preparation

1. Remove the carton and packing foam (including the bottom foam) before using.
2. Clean the unit before using.
3. Adjust the foot to make the unit steady according to the ground
4. After moving the unit, place the unit for 30 minutes before switching it on. Running: close the door and connect the power, turn on the lamp switch on the control panel, the lamp is on. Half an hour later, the temperature inside the caselower apparently, it indicates the unit on be normally used
5. After connecting the power, the unit should be kept empty for one hour

Setting and adjustment of temperature

1. Adjust the storage temperature through the temperature controller located in the internal of the case(see the picture), adjust the temperature according to the ambient temperature and the foodstuff.
2. See the following picture about the knob scale. The temperature adjustable capacity is from “1”-“5”, adjust the storage temperature by turning the temperature controller clockwise. The higher of the number shows the lower of the storage temperature. The knob can turn freely but can’t turn clockwise from “5”to “1”. Factory setting position is on “3”.
3. Check if the scale is on an appropriate position before using, frequent adjustment is not appropriate when using. Normally in summer, the ambient temperature is high, anti clockwise turn the knob to “2”, while in winter, the ambient temperature is low, clockwise turn the knob to “4”.
4. Position “0” represent stop running

Storage of articles

1. Do not put large amount of articles into the unit at one time, you should leave some space around the foodstuff to let cold air inside the cabinet counter to flow. Keep bottled articles away from the walls of interior cabinet so as notto freeze it until broken.
2. Do not put warm food into the unit directly until they are cooled under normal temperature, it will facilitate to lower its energy consumption and prolong service life of the compressor.

Maintenance

Disconnect the power supply before maintenance for the machine!

1. Keep the door gasket clean, remove it from the door and wash it. Dry and seal it as before. Putting some talcum powder on the magnetic surface would prolong its service life.
2. Bulb replacement： remove the lamp shade, take out the bulb, replace with a new bulb, then mount it again.
3. If there is heavy frost on the evaporator after long usage, take out the stuff inside the case, disconnect the power, the frost will melt automatically, clean up the water and connect the power again.
4. Use a soft cloth and dip some water or soap (Non-caustic, neutral detergent is also available) to clean the unit. Dry the unit after cleaning to avoid rust.
5. Do not use organic liquid, boiled water, washing powder or acid stuff to clean the unit. Rinsing the case by water is not allowed, don’t use hard brush, steel brush to clean the case.
6. If the unit will not be used for a long time, disconnect the power, clean it by following the above steps, wipe off the water inside the casewith a soft cloth.

Caution

1. The unit is not suitable for storage of blood, pharmaceutical products and biological products
2. Do not place heavy articles on the top of the unit.
3. In case of trouble, please ask professional person for service, do not dismantle the unit without prior authority to avoid hazard.

Normal Phenomena

1. Sometime hear light sound of water flowing in the unit, this is the sound of refrigerant flowing inside the pipe.
2. In a humidity place, there is dew on the casing or the door, it can dryby dry cloth.

supply
Problems| Possible cause| Ways to solve problems
---|---|---

Abnormal operation of the compressor or has buzz sound

|

The power voltage is out of the rated range.

| Disconnect the power supply immediately and reconnect with it after normal voltage. It is necessary to have a voltage stabilizer in case of poor power supply.
Compressor operates too

long time and no frost on the surface of inner cabinet

|

Refrigeration system is at fault (leakage or blocked)

|

Send the unit to service department for repair

There is frost or ice on the evaporator of the inner cabinet and too low internal temperature, the compressor operates never stop|

Thermostat does not work

|

Ask service department for repair

The internal temperature is too high and the compressor operates never stop

| Bad heat issipation and ventilation of casing, the ambient temperature is too high|

Improve ventilation and ower the ambient mperature.

Too much warm food was put in at one time|

Take out some food

Door open requently and long time door opening|

Decrease number and time of door opening.

Too high noise

| ****

The unit is not level

| ****

Adjust the adjustable feet

The fastener of the unit is loose| ****

Fasten the loose fastener

Pipes are touching the compressor| Careful separating the touched pipes

Lamp is not on

| The lamp is burned out| ****

Replace the lamp

EC declaration of conformity

Hereby I, Company: Frank van Dijk Trading B.V. Declare that the product/article with name: display cooler And model no.: SC98/V097 Is in conformity with relevant union harmonisation directives) and or regulation(s):

• CVC

Tested in accordance with standard(s):

• EN 55014-1:2017. EN 55014-2:2015
• EN 61000-3-2:2014, EN 61000-3-3:2013
• Name: frank van Dijk
• Place: De Kwakel, the Netherlands
• Date: 30-05-2022

Signature and company:
Frank van Dijk Trading B.V.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>