T8 Wireless Charger

Product Information

Specifications

• Charging port: DC connector
• DC Input: 5V
• Input current: 3A Max
• Standby current: 10~30mA
• Working frequency: 113~205K
• TX Output power: 5W, 7.5W, 10W, 15W
• Charging distance: 3~8mm
• Efficiency: 78%
• Working temperature: -10~55°C

Product Usage Instructions

1. Ensure your phone is QI-enabled for wireless charging.

2. Make sure the phone is wireless charging compatible (e.g.,
   iPhone, Samsung, LG, Huawei with fast charging function).

3. Remove the phone case before starting the charging
   process.

4. Connect the wireless charger to a power source using the
   provided DC connector.

5. Place your phone on the wireless charger within the recommended
   charging distance of 3-8mm.

6. Wait for a few seconds for the phone to register as charging (a
   slight delay is normal).

7. The wireless charger supports different output powers (5W,
   7.5W, 10W, 15W); adjust as needed based on your device’s
   compatibility.

8. Monitor the working temperature of the charger to ensure it
   stays within the recommended range (-10~55°C).

FAQ

Q: What phones are compatible with the T8 wireless

charger?

A: The T8 wireless charger is compatible with QI-enabled
wireless charging phones such as iPhone, Samsung, LG, and Huawei
with fast charging function.

Q: Why is there a delay for the phone to register as

charging?

A: A few seconds delay for the phone to register as charging is
normal and part of the wireless charging process.

Q: Can I keep my phone case on while using the wireless

charger?

A: It is recommended to remove the phone case during the
charging process for optimal performance.

Q: What should I do if the wireless charger is not

working?

A: If the wireless charger is not working, ensure that your
phone is QI-enabled and compatible with wireless charging. Check
the power source and connections, and try adjusting the position of
your phone on the charger.

Q: Is FCC certification important for this device?

A: The FCC certification ensures that the device complies with
FCC Rules regarding harmful interference and RF exposure testing.
It is important for safe and compliant operation of the wireless
charger.

User Manual
The T8 wireless charger will only work with QI enabled wireless charging phones. Please check the phone is wireless charging compatible. Note: We recommend removing the phone case during the charging process .
Wireless charger parameters : Charging port DC connector DC Input : 5 V Input current : 3A Max Standby current : 10~30mA working frequency : 113~205K TX Output power : 5W 7.5W 10W 15W Charging distance : 3~8mm Efficiency :78% working temperature : -10~55
Compatible wireless phone: Iphone/Samsung/LG/Huawei with fast charging function
· Using the plug provided, connect the wireless charger cable to the plug and connect to the power source.
· To charge you phone, simply place the phone on the charging position indicator and the phone will start to charge.
· To check if the charger is working, simply move the phone and if the red light is on, this indicates that the charger is working. You may need to reposition the phone slightly if the red light is not showing.
· For the charger to work properly, the charging position within the back of the phone needs to sit aligned with the central red light.
· An element of heat is created during the wireless charging process, this is perfectly normal and safe.The charger has a built in temperature control

and will not over heat. · If a phone has a thick case, it may affect the
wireless charging, to resolve this remove the phone case during charging. · If a phone case is used and charging process seems to stop and start, remove the phone case and try again, this should work better.
NOTE : there may be a few seconds delay for the phone to register as charging which is normal.
For a guidance and help and contact details, please visit our website:
www.frankolsenfurniture.co.uk

FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
The FCC certification of this device refers to RF exposure testing performed in typical operating conditions, where a person is no closer than 20 centimeters from the device surface at all times, except for non-repetitive patterns with transient time intervals in the order of a second. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498.
IC Warning This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The equipment meets the ISED radiation exposure limits set for an uncontrolled environment. During the operation of the device, a distance of 10cm should be kept around the device and above the top surface of the device. Cet appareil est conforme aux CNR exemptes de licence d’Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes: ( 1 ) Ce d ispositif ne peut causer d’interfé rences ; et ( 2 ) Ce d ispositif doit accepter toute interférence , y compris les interfé rences qui peuvent causer un mauvais fonctionnement de l’appareil.
L’équipement respecte les limites d’exposition aux rayonnements ionisants fixées pour un environnement non contrôlé . Pendant le fonctionnement du dispositif, une distance de 10cm devrait être maintenue autour du dispositif et au-dessus de la surface supé rieure du dispositif.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>