MOUNTUP MU2005 Monitor Wall Mount Instruction Manual
- June 16, 2024
- MOUNTUP
Table of Contents
Monitor Wall Mount
Instruction Manual
WARNING!
If you have any confusions or are not quite sure about the installation,
please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are
included and undamaged. Improper installation, such as use the product for
monitors over its load capacity or for any purpose not explicitly specified,
may cause damage or serious injury. We would not be liable for any damage or
injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed.
Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION
IS REQUIRED.
PACKAGE CONTENTS
Installation Tools
ASSEMBLY STEPS
WARNING
DO NOT install into drywall alone.
STEP 1: Attach Arm Assembly to Wall
STEP 2: Attach Decorative Cover
STEP 3: VESA Configures
STEP 4 : Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA plate (B) to back of monitor and secure it by using a 6mm
Allen Key(E) to tighten screws(M-A)
Do not tighten the screws excessively or your monitor might be damaged.
OPTION B: Curved Back Monitor
Attach the VESA plate (B) to back of monitor and secure it by using a 6mm
Allen Key (E) to tighten screws (M-B) along with spacers (M-C).
Do not tighten the screws excessively or your monitor might be damaged.
NOTE: Hand tighten screws to avoid over tightening.
STEP 5: Hang Monitor
Slide the monitor onto the head of swivel arm, install the security bolt (C).
Make sure the security bolt is installed before you rotate the monitor.
Important Notice:
The gas spring is pre-set to minimum tension. Once the monitor is hanged on,
hold the monitor with both hands and DO NOT let go suddenly or immediately.
Instead, leave the monitor in a slow & gentle way while observing whether the
arms will fall down wildly.
Guideline to adjust monitor tilting angle.
Problem:
If monitor face down
Solution:
- Loosen the tilting bolt.
- Hold the bottom of monitor with one hand and adjust to determine your desired tilt angle.
- Retighten the tilting bolt to fix the intended angle.
STEP 6: Adjust Tension
For intended functioning of the mount, you may need to adjust the tension of
Upper Arm (A) in accordance with your monitor weight by 6 mm Allen Key (E).
Note1:
Be sure to keep the arm in horizontal position during adjustment.
Note2:
As for how many circles the screw should be turned, the table below is for
reference.
Monitor Weight| 4.4lbs (2kg)| 6.6lbs (3kg)| 11lbs (5kg)| 17.6lbs (8kg)|
19.8lbs (9kg)| 22lbs (10kg)| 26.4lbs (12kg)
---|---|---|---|---|---|---|---
Circles (AT LEAST)| min| 2| 6| 10| 11| 12| max
STEP 7: Cable Management
Remove bottom plastic covers from gas spring arm as shown in diagram.
Run cables from monitor through bottom of gas spring arm.
Reattach plastic covers as shown in diagram.
Adjust as Desired
Adjust monitor position and rotation.
Note: To ensure stability, the tightness of the rotating axis has been
preset, so it would be kind of dificult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the two sides of
it with both hands, and rotate vigorously.
If that doesn’t work out, please do not hesitate to ask for our help.
Product Dimensions
CAUTION AND MAINTENANCE:
- Never allow children to climb, stand, hang, or play on any part of monitor or stand.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>