COSTWAY TM10012 Baby Activity Center Instruction Manual

Baby Activity Center
TM10012

TM10012 Baby Activity Center

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Before You Start
Please read all instructions carefully and keep it for future reference.
General Warnings

Attention: To prevent possible injury by entanglement, remove this toy when the child starts trying to get up on its hands and knees in a crawling position.
Danger! Keep all small parts and packaging materials for this product away from babies and children, otherwise they may pose a choking hazard.
The product must be installed and used under the supervision of an adult.
Read through each step carefully and follow the proper order.
Remove all packaging, separate and count all parts and hardware before installation.
Please ensure that all parts are correctly installed, incorrect installation can lead to a danger.
We recommend that, where possible, all items are assembled near the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
Ensure a secure surface during installation, and place the product always on a flat, steady and stable surface.

PARTS LIST

WARNING
This product should be assembled by adults. The toys must be used under the direct supervision of adults. Do not play in wet areas.
This manual contains important information. It must be reserved. Throw away other packaging materials such as adhesive tapes, plastic sheets, film bags, ties and labels in time to ensure the safety of children. Please read the instructions carefully before use.

ASSEMBLY STEPS

CAUTION
Do not use with children over 55lbs (25kg), or over 30 inches (76cm). For use only with infant who can hold up their head unaided. Discontinue use when child begins to walk unassisted or can get out of seat on his own.
MODE ONE:SEAT LEG AND PLATFORM ASSEMBLY SEAT AND CLOTH CUSHION ASSEMBLY

INSTALLING TOYS

Note: when installing 4 desktop toys, it is necessary to put two cloth strips into the two holes in the corresponding toy groove of the game desktop, and turn over the back to connect and stick the two cloth strips tightly with each other (the cloth strip comes with Velcro, without using any adhesive tools).
MODE TWO:SEAT LEG AND PLATFORM ASSEMBLY Warm tip: if this form is not used, the two edge accessories can be spliced and stored.
MODE THREE:FITNESS RACK INSTALLATION

MUSIC BOX PERFORMANCE

REQUIRES 2 AAA BATTERIES(NOT INCLUDED) DEMONSTRATION AND INSTALLATION OF FOLDING FUNCTIONAs shown in the figure, press the point A at the bottom of the chair foot to break it apart, repeat the above actions, then shrink and fold the four chair feet to the left side in turn.
FUNCTION DEMONSTRATION AND INSTALLATION OF JUMPING CHAIR

1. As shown in Figure 1 and Figure 2, turning the four legs of the seat in the arrow direction (lock pattern) can lock the bouncing function of the four legs, and switch it to the solid-state game chair. Similarly, turning the four legs of the seat in the arrow direction (unlock pattern) can unlock the bouncing function of the four legs, and switch it to the bouncing chair.
2. As shown in Figure 3, turn the four fixing brackets at the bottom of the seat outward to switch to the solid-state game chair form. Similarly, shrink the four fixing brackets at the bottom of the seat inward to switch to the rocking chair form.

WARNING

1. Please read these instructions and keep it for reference.
   The safety of the child may be endangered if the operation instructions are not used.

2. Prevent children from falling or sliding out of the seat causing serious injury or death.

3. It is your responsibility to protect the safety of children. Therefore, please do not leave the children alone on the chair of the table.

4. Please check whether the surface of the ground and the surface of the table are flat before the table is installed.

5. Before use, please check that the table is firmly installed.

6. Cleaning method: gently wipe with a wet cloth, air dry after wiping.

7. Please do not use parts or replacement parts approved by non manufacturers.

Return / Damage Claim Instructions
DO NOT discard the box / original packaging.
In case a return is required, the item must be returned in original box. Without this your return will not be accepted.
Take a photo of the box markings.
A photo of the markings (text) on the side of the box is required in case a part is needed for replacement. This helps our staff identify your product number to ensure you receive the correct parts.
Take a photo of the damaged part (if applicable).
A photo of the damage is always required to file a claim and get your replacement or refund processed quickly. Please make sure you have the box even if it is damaged.
Send us an email with the images requested.
Email us directly from marketplace where your item was purchased
with the attached images and a description of your claim.

USA office: Fontana
GBR office: Ipswich
AUS office: Truganina
If you’re having difficulty, our friendly
customer team is always here to help. USA :cs.us@costway.com
AUS: cs.au@costway.com
GBR: cs.uk@costway.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>