RAVEtone B0CN9H298D Smart Voice Color Changing LED Night Light User Manual
- June 16, 2024
- RAVEtone
Table of Contents
Smart Voice Color Changing
LED Night Light
—— User Manual —
Hey light
Thank you for your trust !
Congratulations on your new Smart Voice Color Changing Led Night Light.
For a safe handling of the device and in order to get to know the & scope of
features:
- Thoroughly read these user instructions prior o initial use.
- Above all, observe the safety information!
- The device should only be used as described in these user instructions
- Keep this copy of the user instructions for future reference.
- Ifyou pass the device on to someone else, please include this copy of the user instructions
The user instructions are a part of the product.
We hope you enjoy your new Smart Voice Color Changing Led Night Light!
Ata Glance
Light Operation
Specifications
| Input voltage/current | 110230V 50-60HZ |
|---|---|
| Power rating | Max 06W (Warm white) |
| Voice pickup range | Max 3m / 10feet |
| Product size | 6.546.5%4.5 cm |
After-sale Service
If you have any problems during use, Please contact ourafter-sales team first and leave us messages, We will contact you immediately.
Button Operation (Manual)
Short press of the button will switch the light color/modes according to the
following sequence:
Warm-Red-Green-Blue-Purple-Cyan-Pink-White-Yellow Fast Flash:Flash-Colorful
Mode-Dynamic Gradient Mode “Music Mode
Long press to adjust to maximum or minimum brightness.
Voice Control Operation
Directly enter voice commands within 15 seconds after plugging into socket.
Common Voice Commands:
Turn ON/OFF the Light, Change Color, Colorful Mode:
If i takes more than 15 seconds after your last voice commands, you need to
reactivate the device using the wake-up keyword before applying voice
commands.
Wake-up Keywords: Hey Light
Day/ Night Time Mode
The light sensor is deactivated. You can change the device settings (color, brightness, lighting modes) using either voice commands of the operation button, “The light will turn on when you switch to this mode.
The light sensor s activated; the device only operates when the surrounding
light is dim. You can only adjust its settings (color, brightness, and
lighting modes) using voice commands or the operation button after the device
is turned on.
Note:
Please note that you can only switch the modes via voice commands:“Day Time
Mode*and “Night Time Mode’
“Hey light” Wake-up keywords
‘This command activates the light
in two ways:
- the device isinactive for 15 seconds, it enters Standby Mode. To reactivat i justsay “Hey Light”
- When the device is powered off, say “Hey Light” to reactivate ,followed by “Turn on the light” fter a single flash, and then give other commands.
Note:
Upon plugging the device into the socket for the first time, it immediately lights up, allowing direct control through voice commands.
Important Safety Precautions
- Only fitthe LED light i
- properly power socket.
- Do ot attempt to disassemble product.
- Do ot allow this product to have contact with liquids
- Do ot place this product near a heat source or flame.
- Use soft cloth to clear the exterior. Do not use harsh chemicals or strong cleaning solvents
- “This device is not intended for use with emergency exit.
- Do ot subject the device to knocks and vibrations, Knocks and vibrations may damage the sensitive electronics,
Voice Commands Table
| Voice Commands | Command Definition |
|---|---|
| Hey Light | The Wake-up keywords help you to activate the voice control |
feature, please use it if the light doesn’t respond to your voice commands.
The light will flash once to indicate its activation.
Day Time Mode| The light sensor is deactivated, you can change its status
(color, brightness, lighting modes) with the voice commands or operation
button.
Night Time Mode| The light sensor Is activated, the device only works while
the surrounding light level is low. You only can change its status (color,
brightness, lighting modes) after it turns on.
Turn on the Light
Switch on the light (00u0| The LED lights up.
Turn off the Light
Switch off the Light (option)| Switch off the light.
Change Color| Switch the light color in the following sequence: Warm-Red-
Green-Blue-Purple-Cyan-Pink-White-Yellow
Colorful Mode| Quick command for breathing light mode.
Change the Mode| Switching four colorful lighting modes in sequence: Fast
Flash-Flash-Colorful Mode-Dynamic Gradient Light
Music Mode| Make the light blink In sync with the rhythm of the music.
If no sound detected, the light will change to breathing light mode.
Brighten the Light| Increase in brightness level. (5 brightness levels
include) The light will flash when reaching full brightness.
Dim the Light| Diminish in brightness level. (5 brightness levels include) The
light will flash when reaching minimum brightness.
Maximum Brightness| Adjust the Brightness to Maximum level.
Minimum Brightness| Adjust the Brightness to Minimum level.
Warm Light| Change the light color to warm.
Red Light| Change the light color to red.
Green Light| Change the light color to green.
Blue Light| Change the light color to blue.
Purple Light| Change the light color to purple.
Cyan Light| Change the light color to cyan.
Pink Light| Change the light color to pink.
White Light| Change the light color to white.
Yellow Light| Change the light color to yellow.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>