Honeywell CCB01-010BT Charge Base User Guide

: July 25, 2024
: Honeywell

Table of Contents

Getting Started
Power Supply Assembly (if included)
Keyboard Wedge:
LED Sequences and Meaning
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CCB01-010BT
Charge Base
Technical Specifications
CCB01-010BT-EN-TS Rev B
02/19

Note: Refer to your user’s guide for information about cleaning your device.

Getting Started

Turn off the computer’s power before connecting the base, then power up the computer once the base is fully connected. When the base is connected and powered up, put the scanner in the base to establish a link. The green LED on the base flashes to indicate the scanner’s instant charge pack is charging. The scanner must be returned to the base when not in use. Ascanner charged on the base with the power supply for 35 seconds will result in 100 scans, with one scan every second.

Power Supply Assembly (if included)

Note: The power supply must be ordered separately, if needed.

Keyboard Wedge:

RS232 Serial Port:

RS485:

LED Sequences and Meaning

When charging, the base indicates the progress while the scan- ner resides in the base.

Base Button/LED| Charge Level| Approximate
**Expected Scans***
---|---|---
Green on| 100%| 450
Green slow blink| 50-99%| 200
Green fast blink| 30-50%| 100
Yellow fast blink| 0-30%| Charging – do not scan

CCB01-010BT and CCB01-010BT-BF Charge and Communication Base

Agency Models: CCB01-010BT, CCB01-010BT-BF

Product documentation is available at sps.honeywell.com.

FCC Part 15 Subpart B Class B
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio or television technician for help.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. Honeywell International Inc. is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Honeywell International Inc.. The correction is the responsibility of the user.

UL and C-UL Statement
UL and C-UL listed: UL 62368-1, Second Edition and CSA C22.2 No.62368-1-14, Second Edition.

Caution: Any changes or modifications made to this equipment not expressly approved by Honeywell International Inc. may void the authorization to operate this equipment.

RF Exposure
The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Canadian Compliance
This ISM device complies with Canadian RSS-247.
Operation is subject to the following conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

Use only shielded data cables with this system. This unit has been tested with cables less than 3 meters. Cables greater than 3 meters may not meet class A performance.

Frequency 2402-2480 MHz
Maximum power 20dBm

CAUTION: Improper battery replacement or incompatible device usage may result in risk of burns, fire, explosion, or other hazard. Dispose of lithiumion batteries according to local regulations.

CB Scheme
Certified to CB Scheme IEC 623681, Second Edition.

Product Environmental Information
Refer to honeywell.com/PSSenvironmental for the RoHS / REACH / WEEE information.

This document was prepared and executed in the English language. In the event this document is translated into another language and a conflict arises between the English version and a non-English version, the English version shall prevail, it being recognized and acknowledged that the English language version most clearly expresses the intent of the parties. Any notice or communication given in connection with this document must include a version in the English language.

The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.

For warranty information, go to sps.honeywell.com and click Support > Warranties.

The following statements may not apply to products assembled in Mexico:

Honeywell International Inc., hereby declares that the radio equipment type, non-specific SRD, is in compliance with the following directives:
• 2014/53/EU Radio Equipment
• 2011/65/EU RoHS (Recast)
The full text of the EU declaration of conformity is available at the following internet address: honeywell.com/PSScompliance.
European contact: Honeywell Productivity Solutions
BV
Burgemeester Burgerslaan 40
5245NH Rosmalen
The Netherlands

United Kingdom Contact: United Kingdom Honeywell Scanning and Mobility, Honeywell House, Skimped Hill Lane, Bracknell, Berkshire, RG12 1EB Phone: +44 (0)1344921052

NCC standard: Low-power Radio-frequency Devices Technical Regulations: LP0002

If the following label is attached to your product, the product meets Korean agency approval for Class B equipment:

(Model) : CCB01-010BT, CCB01-010BT-BF
(Names and Content of Hazardous Substances in the Product)

(Parts Name)	(Hazardous Substances)
(Pb)	(Hg)
(PCB)	x
(Housing)	o
(Cables)	o

(The table is created by SJ/T11364 requirement.)
o: (Indicates that this hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in China’s GB/T26572.)
x: (Indicates that this hazardous substance contained in at least one of the homogeneous materials for this part is above the limit requirement in China’s GB/T26572.)

Honeywell International Inc.
9680 Old Bailes Road
Fort Mill, SC 29707 USA
©2023 Honeywell Group of Companies.
All rights reserved.
The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.

CCB01-010BT TS Rev B 2/19
© 2019 Honeywell International Inc.