SIQURA 9050BF 19 Inch Rack Mount Chassis User Manual
- June 16, 2024
- SIQURA
Table of Contents
SIQURA 9050BF 19 Inch Rack Mount Chassis
Product Information
Specifications
- Product Name: SIQURA 9002, 9050BF
- Rack-mount chassis with power supply
- Number of slots: 21
- Type of slot: 9000 series rack-mount cards
- Dimensions (h x w x d): 177.8 x 442.6 x 203.2 mm (7 x 19 x 8)
- Weight: 2.72 kg (6 lbs)
- Power supply (9050BF):
- Input voltage range: N/A
- Output voltage: N/A
- Maximum current: N/A
- Maximum current derated: N/A
- Number of fans: N/A
- Number of slots used: N/A
- Dimensions (h x w x d): N/A
- Weight: N/A
- Operating temperature: N/A
- Storage temperature: N/A
- Relative humidity: N/A
Features
- Rack-mountable chassis
- Supports up to 21 slots for 9000 series rack-mount cards
- 3-slot, heavy-duty, fan-cooled power supply module
- Output voltage, current, and temperature monitoring
Ordering Information
- 9002
- 9050BF
- 9996
- 9998
Product Usage Instructions
Installation
- Choose a suitable location for the rack-mount chassis.
- Ensure proper ventilation around the chassis to prevent overheating.
- Place the chassis in the desired position and secure it using the provided mounting brackets.
- Connect the power supply module to a suitable power source.
- Insert the desired 9000 series rack-mount cards into the available slots.
Monitoring and Maintenance
To monitor the output voltage, current, and temperature:
- Access the monitoring interface of the rack-mount chassis.
- View the displayed values for voltage, current, and temperature.
- If any abnormal values are detected, refer to the troubleshooting section of the user manual for further instructions.
Replacing Rack-Mount Cards
- Power off the rack-mount chassis and disconnect the power supply.
- Remove any connected cables from the rack-mount cards.
- Carefully remove the rack-mount card from its slot by releasing any securing mechanisms.
- Insert the new rack-mount card into an available slot, ensuring proper alignment.
- Secure the card in place using any provided securing mechanisms.
- Reconnect any cables that were disconnected.
- Power on the rack-mount chassis and verify proper operation.
Cleaning
To clean the rack-mount chassis:
- Power off the rack-mount chassis and disconnect the power supply.
- Use a soft, lint-free cloth to gently wipe the exterior surfaces of the chassis.
- Avoid using harsh chemicals or abrasive materials that may damage the finish.
- Ensure all surfaces are dry before reconnecting the power supply and powering on the chassis.
FAQ
-
Q: What is the maximum number of slots supported by the rack-mount chassis?
A: The rack-mount chassis supports up to 21 slots for 9000 series rack-mount cards. -
Q: How can I monitor the output voltage, current, and temperature?
A: You can access the monitoring interface of the rack-mount chassis to view the displayed values for voltage, current, and temperature. -
Q: How do I replace a rack-mount card?
A: To replace a rack-mount card, power off the chassis, remove any connected cables, carefully remove the card from its slot, insert the new card into an available slot, secure it in place, reconnect any cables, and power on the chassis.
DESCRIPTION
The Model 9002 19″ 4 RU chassis is designed for rack mounting Optelecom® Series 9000 cards. All electrical and optical connections are made to the front panels of the plug-in cards. Individual cards can be hot swapped without affecting the operation of other cards in the chassis. The rack mounting ears may be installed on the front or rear of the chassis as required for the specific application. The 9002 may be equipped with one or two power supplies (9050BF). You can set these supplies to operate as load-sharing or as primary and backup supplies. 18 slots are available for use with one supply installed; 15 are available with two supplies installed. The chassis supports the Network Management System.
FEATURES
- Rack-mountable chassis supports 9000 series rack-mount cards.
- Supports up to 21 slots.
- 3-slot, heavy-duty, fan-cooled power supply module.
- Output voltage, current, and temperature monitoring.
9050BF rack-mount power supply
These 6.0VDC power supplies are intended to meet the requirements of Series
9000 chassis rack mount units. The supplies may be operated as a single supply
or, when two supplies are installed, primary/backup mode or load-sharing mode.
Adjustments are made simple by a set of front panel meter test points for
output voltage, current, and temperature and a voltage adjustment control. For
noise immunity and proper ventilation, install blank panels over unused slots.
See the accessories chart in Ordering Information below. Power supplies are
ordered separately; the version of supply required depends on the number of
cards installed and their total power consumption. Refer to the User Manual
and system applications notes available from the factory for details on
installing the 9002 chassis.
SPECIFICATION
- Mechanical
- Number of slots 21
- Type of slot 9000 series
- Dimensions (h x w x d) 19″/4RU: 177.8 x 442.6 x 203.2 mm (7″ x 19″ x 8″)
- Weight 2.72 kg (6 lbs)
- Power supply (9050BF)
- Input voltage rang 100-240VAC, 50/60Hz
- Output voltage 6.1 Vdc
- Maximum current 24A at -40°C to +50°C (-40°F to +122°F)
- Maximum current derated 13.5A at -40°C to +65°C (-40°F to +149°F)
- Number of fans 1
- Number of slots used 3
- Dimensions (h x w x d) 154.9 x 60.9 x 218.4 mm (6.1″ x 2.4″ x 8.6″)
- Weight 1.45kg (3.2lbs)
- Environmental
- Operating temperature -40°C to +74°C (-40°F to +165°F)
- Storage temperature -55°C to +85°C (-67°F to +185°F)
- Relative humidity <95% with no condensation
- Ordering information
- 9002 21-slot 19″ rack-mount chassis (without power supply unit, 9050BF)
- 9050BF 3-slot power supply unit for use with the 9002 chassis
- 9996 1 single blank panel (1-slot cover plate)
- 9998 1 triple blank panel (3-slot cover plate)
DIMENSIONS
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>