SCHMERSAL AZ 16 ZVRK-ST-2300 Safety Switch With Separate Actuator Instruction Manual
- June 16, 2024
- SCHMERSAL
Table of Contents
Safety switch with separate actuator AZ 16 ZVRK-ST-2300
Instruction Manual
About this document
1.1 Function
This document provides all the information you need for the mounting, set-up
and commissioning to ensure the safe operation and disassembly of the
switchgear. The operating instructions enclosed with the device must always be
kept in a legible condition and accessible.
1.2 Target group of the operating instructions: authorised qualified
personnel
All operations described in the operating instructions manual must be carried
out by trained specialist personnel, authorised by the plant operator only.
Please make sure that you have read and understood these operating
instructions and that you know all applicable legislations regarding
occupational safety and accident prevention prior to installation and putting
the component into operation.
The machine builder must carefully select the harmonised standards to be
complied with as well as other technical specifications for the selection,
mounting and integration of the components.
The information contained in this operating instructions manual is provided
without liability and is subject to technical modifications.
1.3 Explanation of the symbols used
Information, hint, note: This symbol is used for identifying useful
additional information.
Caution: Failure to comply with this warning notice could lead to
failures or malfunctions.
Warning: Failure to comply with this warning notice could lead to
physical injury and/or damage to the machine.
1.4 Appropriate use
The Schmersal range of products is not intended for private consumers.
The products described in these operating instructions are developed to
execute safety-related functions as part of an entire plant or machine. It is
the responsibility of the manufacturer of a machine or plant to ensure the
correct functionality of the entire machine or plant.
The safety switchgear must be exclusively used in accordance with the versions
listed below or for the applications authorised by the manufacturer. Detailed
information regarding the range of applications can be found in the chapter
“Product description”.
1.5 General safety instructions
The user must observe the safety instructions in this operating instructions
manual, the country specific installation standards as well as all prevailing
safety regulations and accident prevention rules.
Further technical information can be found in the Schmersal catalogues or in
the online catalogue on the Internet:
products.schmersal.com.
Product description
2.1 Ordering code
| none | 1 NO contact/1 NC contact |
|---|---|
| 2 | 2 NC contacts |
| 3 | 3 NC contacts |
| 12 | 1 NO contact/2 NC contact |
(2)
none| Resilience
R| Fastening force 30N
(3)
G24| With LED (only for version with one NO contact and one NC contact)
(4)
M16| Cable entry M16
M20| M20 wiring port
ST| Connector M12, 4-pin, bottom
STL| Connector M12, 4-pin, left
STR| Connector M12, 4-pin, right
(5)
2254| Fastening force 5N
1762| Upper end installation
1637| gold plated contacts
2.2 Special versions
For special versions, which are not listed in the ordering code, these
specifications apply accordingly, provided that they correspond to the
standard version.
2.3 Purpose
The safety switches with separate actuator are suitable for sliding, hinged
and removable safety guards, which need to be closed in order to ensure the
necessary operational safety.
The safety switches are used for applications, in which the hazardous
situation is terminated without delay when the safety guard is opened.
When the safety guard is opened, the NC contacts are positively opened and the
NO contacts are closed.
The safety switchgears are classified according to EN ISO 14119 as type 2
interlocking devices.
The user must evaluate and design the safety chain in accordance with the
relevant standards and the required safety level.
The entire concept of the control system, in which the safety component is
integrated, must be validated to the relevant standards.
2.4 Warning about misuse
In case of improper use or manipulation of the safety switchgear, personal
hazards or damages to machinery or plant components cannot be excluded. There
are no residual risks, provided that the safety instructions as well as the
instructions regarding mounting, commissioning, operation and maintenance are
observed.
2.5 Exclusion of liability
We shall accept no liability for damages and malfunctions resulting from
defective mounting or failure to comply with the operating instructions
manual. The manufacturer shall accept no liability for damages resulting from
the use of unauthorised spare parts or accessories.
For safety reasons, invasive work on the device as well as arbitrary repairs,
conversions and modifications to the device are strictly forbidden, the
manufacturer shall accept no liability for damages resulting from such
invasive work, arbitrary repairs, conversions and/or modifications to the
device.
2.6 Technical Data
Note about the safety classification
Basically suitable up to Cat. 1 / PL c.
With 2-channel usage with fault exclusion mechanism (if a fault exclusion to
the 1-channel mechanics is authorised) and suitable logic applicable up to
Cat. 3 / PL d
(Determined values can
vary depending on the application-specific parameters hop , dop and tcycle If
multiple safety components are wired in series, the Performance Level to EN
ISO 13849-1 will be reduced due to the restricted error detection under
certain circumstances.
Mounting
3.1 General mounting instructions
Please observe the relevant requirements of the standards ISO 12100, ISO 14119
and ISO 14120. as well as the load.)
The mounting dimensions are indicated on the rear of the component. The
enclosure must not be used as an end stop.
Any mounting position. The mounting position however must be chosen so that
the ingress of dirt and soiling in the used opening is avoided. The unused
openings must be sealed by means of slot sealing plugs (AZ 15/16 – 1476-1
available as accessory) after fitting.
3.2 Mounting of the actuator
See operating instructions Actuator.
The actuator must be permanently fitted to the safety guards and protected
against displacement by suitable measures (tamperproof screws, gluing,
drilling of the screw heads).
| R min| d| R min| d
---|---|---|---|---
AZ 15/16-B2| –| –| 45| 11
AZ 15/16-B2-1747| –| –| 45| 11
AZ 15/16-B3| 32| 11| –| –
AZ 15/16-B3-1747| 32| 11| –| –
AZ 15/16-B6| 25| 11| 38| 11
3.3 Dimensions
All measurements in mm. 
Electrical connection
4.1 General information for electrical connection
The electrical connection may only be carried out by authorised personnel in a
de-energised condition.
The contact labelling can be found in the wiring compartment of the switch.
Appropriate cable glands with a suitable degree of protection are to be used.
Settle length x of the conductor: 6 mm
After wiring, dust and soiling must be
removed from the wiring compartment. The safety switch is double insulated.
The use of a protective ground connector therefore is not authorised.
4.2 Contact Options
Contacts are shown with safety guard closed. All NC contacts have positive
break →.
Set-up and maintenance
The safety function of the safety components must be tested. In the case of correct installation and adequate use, the safety switchgear features maintenance-free functionality. A regular visual inspection and functional test, including the following steps, is recommended:
- Check for free movement of the actuating element
- Check cable entry and connections
- Check the switch enclosure for damage
- Remove particles of dust and soiling
Adequate measures must be taken to ensure protection against tampering either
to prevent tampering of the safety guard, for instance by means of replacement
actuators.
Damaged or defective components must be replaced.
Disassembly and disposal
6.1 Disassembly
The safety switchgear must be disassembled in a de-energised condition only.
6.2 Disposal
**** The safety switchgear must be disposed of in an appropriate manner in
accordance with the national prescriptions and legislations.
Schmersal Industrial Switch Manufacturing (Shanghai) Co., Ltd.,
No. 3336 Caoying Road, Qingpu District, Shanghai,
The details and data involved have been carefully checked.
Image may vary from original image.
You can find further technical data in the instructions.
There may be technical modifications and errors.
Generated date 2024/1/11 12:21 pm
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>