DEWERT OKIN FP2401 USB To Wireless Antenna Adapter Instructions
- June 16, 2024
- DEWERT OKIN
Table of Contents
DEWERT OKIN FP2401 USB To Wireless Antenna Adapter
Product Information
Specifications
- Date: 11.10.2023
- Product: USB Antenna
- Manufacturer: DOT and relevant manufacturing plants
Usage Instructions
Purpose
This test instruction describes the incoming goods inspection of the USB to
Wireless Antenna adapter.
Preparation / Connecting
Before using the USB Antenna, please follow the steps below:
- Ensure that your device is turned off.
- Locate the USB port on your device.
- Insert the USB Antenna adapter into the USB port firmly.
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Please note that any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
ISED Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
RF Exposure Limits
- This equipment should be installed and operated with a minimum distance of 0cm between the radiator and your body to comply with FCC radiation exposure limits set forth for an uncontrolled environment.
- For Canadian users, this equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. Users can obtain Canadian information on RF exposure and compliance.
FAQ
-
Q: What is the purpose of the USB Antenna?
A: The USB Antenna is designed to provide wireless connectivity to devices through a USB port. -
Q: How do I connect the USB Antenna?
A: Please follow the steps below to connect the USB Antenna:- Turn off your device.
- Locate the USB port on your device.
- Insert the USB Antenna adapter firmly into the USB port.
-
Q: What are the FCC compliance requirements for this device?
A: This device complies with part 15 of the FCC Rules. It should not cause harmful interference and must accept any interference received. -
Q: Are there any radiation exposure limits for using this equipment?
A: Yes, this equipment should be installed and operated with a minimum distance of 0cm between the radiator and your body to comply with FCC and Canada radiation exposure limits.
Test instruction for USB Antenna
Date: 11.10.2023
-
Scope
DOT and the relevant manufacturing plants -
Purpose
This test instruction describes the incoming goods inspection of the USB to Wireless Antenna adapter. -
Terms and abbreviations
– none –
Competence
- Initiator of creation: [11.10.2023]
- Creator of the instruction: [Zannoni Luca]
- Initiator of modification: [ – / – / – ]
- Creator of the modified instruction: [ – / – / – ]
Change information
| Index | Date | Changing | Workflow | Name |
|---|---|---|---|---|
| 01 | 11.10.2023 | · First Release | Zannoni |
Procedure/method description
– see the following pages –
Applicable documents
– none –
Documentation
All pictures shown are for illustration purpose only. Actual product may vary.
Required testing equipment
- Antenna USB to Wireless Adapter
- Control Box (CB 19.20.01)
- IMPORTANT NOTE: The control box must be already paired with the following radio frequency settings.
- Power Supply (JLDP.10.079.101)
- Actuator (JLDQ.20.495.344K01)
Preparation / Connecting
Testing
- Connect the antenna to an USB port
- Open OTA Service Tester software
- Select COM number from “Comm” panel
- Click “Closed” from Comm Port panel (”Closed” switches to “Open”)
- Click “Update Bridge Params” from the Pairing Parameters panel
- Click “Open All” from the Motor Action panel (Motor should open)
- Click “Return” from the Motor Action panel (Motor should close)
FCC Warning
- This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.
ISED Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
- The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
- This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on
RF exposure and compliance.
- This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
- This equipment should be installed and operated with minimum distance 0cm between the radiator & your body.
Test instruction/Creator: TD
This document is valid without signature!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>