MOUNTUP MU0027 Single Monitor Desk Mount Gaming Monitor Arm Stand Mount Instruction Manual
- June 16, 2024
- MOUNTUP
Table of Contents
Gaming Counterbalance Desk Mount
Instruction Manual
MU0027 Single Monitor Desk Mount Gaming Monitor Arm Stand Mount
MA07-12-US3.0
If you have any questions, please feel free to contact Customer Service via
Amazon before returning.
WARNING!
If you have any confusion or are not quite sure about the installation, please
do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are
included and undamaged. Improper installation, such as using the product for
monitors over its load capacity or for any purpose not explicitly specified,
may cause damage or serious injury. We would not be liable for any damage or
injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed.
Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION
IS REQUIRED.
PRODUCT LINE GRAPH
PACKAGE CONTENTS
Components Hardware
Warm Tips You could also refer to the Video Guide about installation on our
product page.
STEP 1 Mount the Base to Bottom of the Arm
Mount the base(L) to the bottom of arm (A) using Washer(M), calathiform
gasket(N) and Bolt(O).
Tighten (do not over tighten) the Bolt (O) securely with supplied 5mm Allen
key (Q).
STEP 2 Clamp Installation OR Grommet Base Installation
OPTION A: Clamp Installation
Mount bracket (C) to the bottom of arm (A) using screws(J). Tighten the screws
with supplied 4mm Allen key (P). Adjust the Mount to the Desktop Thickness
10-55mm
Secure clamp (D) to upper two holes with bolts (J) using 4mm Allen Key (P) for
desks with a thickness of 10-55mm. Adjust the Mount to the Desktop
Thickness 50-85mm
Secure clamp (D) to lower two holes with bolts (J) using 4mm Allen Key (P) for
desks with a thickness of 50-85mm.Attach bracket cover (E)to bracket(C).
Tighten the clamp to the desktop using the plastic knob or by using 6mm Allen
key (R). OPTION B: Grommet Base Installation
For grommet hole mounting, place long bolt(F) through the center of grommet
base (G).
Mount grommet base to the bottom of arm (A) using screws(J). Tighten the
screws with supplied 4mm Allen key (P). Run long bolt(F) through grommet hole
in desktop. Secure it by using the support plate (H) and Wingnut (K). Tighten
Wingnut.
STEP 3 Attach the monitor to the arm
OPTION A: Flat Back Monitor
Attach the VESA plate (B) to the back of monitor and secure it by using a 6 mm
Allen Key (R) to tighten screws (M-A).
Do not tighten the screws excessively or your monitor might be
damaged. OPTION B: Curved Back Monitor
Attach the VESA plate (B) to the back of monitor and secure it by using a 6 mm
Allen Key (R) to tighten screws (M-B) along with spacers (M-C).
Do not tighten the screws excessively or your monitor might be
damaged.Slide the monitor onto the head of swivel arm(A), install the
security screw (I). Make sure the security screw is tightened before you
rotate the monitor. **** Refer to below illustrations to adjust tilting angle
of your monitor.
Problem:
If monitor face down
Solution:
- Loosen the tilting bolt.
- Hold the bottom of monitor with one hand and adjust to determine your desired tilt angle.
- Retighten the tilting bolt towards “+” to fix the angle.
STEP 4 Adjust the tension
For proper functioning of this mount, depending on different weight of monitor
you might need to adjust tension spring in Arm (A) by using 6 mm Allen key
(R).
After being attached to the arm, the monitor falls down and can not stay at
the desired height by itself.
Turn clockwise(“+”direction) to increase tension until the monitor can stay at
the desired Height by itself.
After being attached to the arm, the monitor rises up and can not stay at the
desired height by itself.
Turn counter-clockwise(“-”direction) to reduce tension until the monitor can
stay at the desired Height by itself.
Note:
It is normal for a bit noise when you adjust the spring tension.
Note2:
For how many circles the screw should be turned, please refer to the table
below.
Monitor Weight| 4.1Igbs| &Alps| 8.41k1gbs| 1 5,I,bs| 1 341bs| 1 5.41bs
(74)| 1 7.6g)Ibs
(8k
---|---|---|---|---|---|---|---
Circles(AT LEAST)| min| 3| 4| 6| 8| 10| 12
STEP 5 Cable Management
Remove the bottom plastic covers from spring arm(A) as shown in diagram. Run
cables from monitor through the bottom of spring arm (A). Reattach plastic
covers as shown in diagram.
Adjust as Desired
Allen Key(P,Q) can be stored in Base Support Cover(E) for next time using.
Note: To ensure stability, the tightness of the rotating axis has been
preset, so it would be kind of diffcult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the two sides of it
with both hands, and rotate vigorously.
If that doesn’t work out, please do not hesitate to ask for our help.
**** CAUTION AND MAINTENANCE
- Never allow children to climb, stand, hang, or play on any part of monitor or stand.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>