BRAYER BR3130 Hot Air Styler Instruction Manual

: June 4, 2024
: BRAYER

Table of Contents

DESCRIPTION
SAFETY MEASURES AND OPERATION RECOMMENDATIONS
BEFORE USING THE KETTLE
USING THE HOT AIR STYLER
Overheating protection
CLEANING AND MAINTENANCE
STORAGE
TECHNICAL SPECIFICATIONS
RECYCLING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BRAYER BR3130 Hot Air Styler Instruction Manual

The hot air styler is used for styling dry or slightly wet hair.

DESCRIPTION

Brush attachment
Attachment installation place
Attachment lock «PUSH»
Operation mode switch «0 – C – 1 – 2»
Body
Air inlets
Hanging loop
Superbrush with extensive airflow
Nozzle

ATTENTION!

Do not use the unit near water in the bathrooms, showers, swimming pools etc.
After using the unit in a bathroom, unplug it and take the power plug out of the mains socket, as the proximity of water is dangerous even if the unit is switched off.
For additional protection it is reasonable to install a residual current device (RC D) with nominal operation current not exceeding 30 mA into the mains of a bathroom. To install it, contact an electrical technician

SAFETY MEASURES AND OPERATION RECOMMENDATIONS

Read the operation instructions carefully before using the unit, after reading keep them for future reference.

Use the unit for its intended purpose only, as it is stated in this manual.
Mishandling the unit can lead to its breakage and cause harm to the user or damage to his/her property and it is not covered by warranty.
The hot air styler is intended only for styling of slightly wet and dry hair, do not use the unit for styling of wet hair or synthetic wigs.
Make sure that operating voltage of the unit indicated on the label corresponds to your home mains voltage.
Do not use the unit when you are drowsy.
Do not use the unit outdoors.
It is recommended not to use the unit during lightning storms.
Protect the unit from blows, drops, vibrations and other mechanical stress.
Never leave the plugged-in hot air styler unattended.
Do not use the unit near heating appliances, heat sources or open flame.
Do not use the unit in places where aerosols are used or sprayed, and in proximity to inflammable liquids.
Do not use the unit in proximity to kitchen sink, in bathrooms, near swimming pools or other containers filled with water.
Do not use the unit while taking a bath.
Do not hang and do not keep the unit in places where it can fall into a bath or a sink filled with water; do not immerse the unit body, power cord or power plug into
water or any other liquid.
If the unit is dropped into water, unplug it immediately, and only then you can take the unit out of water.
Do not let the power cord touch hot surfaces and sharp edges of furniture.
Unplug the unit after usage or before cleaning. When unplugging the unit hold the power plug and carefully remove it from the mains socket, do not pull the power cord — this can lead to its damage and cause short circuit.
Do not touch the unit body, the power cord and the power plug with wet hands.
Avoid contact of hot surfaces with your face, neck and other parts of your body.
Do not direct hot air into your eyes or other heatsensitive parts of your body.
The attachment gets hot during operation. Allow it to cool down before removal.
Never insert any foreign objects into any unit body openings.
Do not block the air inlets of the hot air styler, do not place it on a soft surface, where the air inlets may be blocked. Keep the air inlets free of lint, dust, hair etc.
Clean the unit regularly.
Unplug the unit after usage and before cleaning.
For children safety reasons do not leave polyethylene bags used as a packaging unattended.

ATTENTION!

Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!

The hot air styler is not intended for usage by children.
Do not leave children unattended to prevent using the unit as a toy.
Do not allow children to touch the operating surface, unit body, power cord or power plug during operation of the unit.
Be especially careful if children or disabled persons are near the operating unit.
During the unit operation and breaks between operation cycles, place the unit out of reach of children.
The unit is not intended for usage by physically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
Regularly check the integrity of the power cord.
If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.
Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after the unit was dropped, unplug it and apply to the service center.
To avoid damages, transport the unit in the original package.
Keep the unit in a dry cool place out of reach of children and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY

BEFORE USING THE KETTLE

After unit transportation or storage at negative temperature, unpack it and wait for 3 hours before using.

Unpack the unit and remove all the packaging materials

Keep the original package.
Check the delivery set.
Read the safety measures and operating recommendations.
Examine the unit for damages, in case of damage do not plug it into the mains.
Make sure that specified specifications of power supply voltage of the unit correspond to the specifications of your mains. When using the unit in the mains with 60 Hz frequency, the unit does not need any additional settings.
Wipe the unit with a clean, slightly damp cloth to remove dust, and then wipe it dry.
Unwind the power cord to its full length while using the unit.

USING THE HOT AIR STYLER

Make sure that the operation mode switch (4) is set to the position «0».
Insert the necessary attachment (1, 8, 9) into the installation place (2) and turn it until the lock (3) «PUSH» clicking, make sure the attachment (1) is fixed properly (pic. 1).
Insert the power plug into the mains socket.
Use the switch (4) to switch the hot air styler on:
- «0» — the hot air styler is off;
- «C» — cool air supply;
- «1» — low air flow speed;
- «2» — high air flow speed;
Note: During the first operation a foreign smell and a small amount of smoke can appear from the heating element, this is normal and it is not covered by warranty.
After the hot air styler operation is finished, switch it off by setting the switch (4) to the «0» position and unplug it.
Wait until the set attachment (1) cools down.
To remove the attachment, press the lock (3) «PUSH», turn and remove the attachment (pic. 1).
Periodically straighten the power cord if it gets twisted during operation.

Overheating protection

The overheating protection system switches the hot air styler off if the temperature of the outgoing air is above the limit.
If the hot air styler is switched off during operation, set the switch (4) to the «0» position, unplug the unit and make sure that the air inlets and outlets are unblocked.
Let the unit cool down for 5-10 minutes and then switch it on again. Do not block the air inlets during operation of the hot air styler and
avoid getting of hair into the air inlets (6).

CLEANING AND MAINTENANCE

The hot air styler is intended for household use only.

Set the switch (4) to the «0» position, disconnect the hot air styler from the mains and let it cool down.
To remove the attachment, press the lock (3) «PUSH», turn and remove the attachment.
Wipe the unit body (5) with a slightly damp cloth, and then wipe it dry.
Clean the air inlets (6) with a brush.
Do not immerse the unit into water or any other liquids.
Do not use abrasives and solvents to clean the unit body (5) and the attachment (1).

STORAGE

Disconnect the unit from the mains and clean it.
Never wind the power cord around the hot air styler, as this can lead to its damage or damage of the unit body.
A hanging loop (7) you can hang the hot air styler on is provided for the ease of the unit storage, given that no water will get on the hot air styler.
Keep the unit in a dry cool place out of reach of children and disabled persons. deLIVERY SET
Hot air styler — 1 pc.
Brush attachment — 1 pc.
Manual — 1 pc.

TECHNICAL SPECIFICATIONS

Supply voltage: 220-240 V, ~ 50/60 Hz
Rated input power: 600-700 W

ATTENTION!

ATTENTION Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!

RECYCLING

To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after service life expiration of the unit or the batteries (if included), do not discard them with usual household waste, deliver the unit and the batteries to specialized centers for further recycling

The waste generated during the disposal of the unit is subject to mandatory collection and consequent disposal in the prescribed manner

For further information about recycling of this product apply to a local municipal administration, a disposal service or to the shop where you purchased this product

The manufacturer reserves the right to change the design, structure and specifications not affecting general principles of the unit operation, without prior notice.

The unit operating life is 3 years

Logo