RainPoint TCS024B Bluetooth Soil Moisture Meter User Manual
- June 16, 2024
- RainPoint
Table of Contents
RainPoint TCS024B Bluetooth Soil Moisture Meter
INTRODUCTION
Product Overview
Button Function
- Hold the button to enter connection mode.
- Press the button to make a real- time detection and the result will be shown on the APP.
Specification
- Waterproof Level: IP54
- Temperature Range: 0°C- 60°C
- Moisture Range: 1 %RH-99%RH
- Communication by Bluetooth
- Powered by 3*AAA batteries (Not included)
Product Features
- Measures soil moisture(%) and air temperature (°C/F).
- App control for easy setup and operation.
- Used in indoor planters, learning more about areas of soil information.
- When the batteries are low, a short press on the button will cause the red light to flash rapidly for 3 times. The device will not perform any detection, and the app will display a low battery indication.
INSTALLATION AND CONNECTION
Tips:
Please scan the QR code or search the link to access the Setup Video or FAQ to
install the device quickly and easily.
Setup Video:
www.rainpointus.com/pages/playlist
FAQ:
www.rainpointus.com/downloads/faq
Setup
Video
|
Customer Support
---|---
Installing the APP
-
Download the Rain Point APP Search for “Rain Point” on Google Play/App Store or scan the QR code to download the Rain Point APP.
-
Register your Rain Point account Open your Rain Point APP, select “Set Up” , and then follow the prompts to register a Rain Point account with your email or mobile phone.
Connecting the Soil Moisture Meter
Connecting the Soil Moisture Meter to the Rain Point APP
A ) After account created, in the home page of the APP, click “ + ”
on the top right corner, or then click “Add Device” to search and add
devices.
B )Tap “Smart Irrigation”, then select “Bluetooth Soil Moisture
Meter”.
Note: Before adding the soil moisture meter, please turn on the Bluetooth for pairing.
C ) Installing the Battery
-
Remove the battery cover from the back of the unit with a screwdriver.
-
Insert the battery, close the battery cover and tighten the screws.
D ) After the battery is correctly installed, the green LED indicator
will start flashing rapidly ( 2 times per second ) to enter pairing
mode automatically, make sure the Bluetooth has been opened, and tap “Next”.
Then select “ Make sure the device is in the state of network distribution
” and tap “Next”.
The APP will search and pair your Bluetooth soil moisture meter automatically.
Tips: Besides that, you can also hold the button for 5 seconds to reset
and reconnect if you fail to connect for the first time. (Please refer to the
“RESETTHE DEVICE” to reset the soil moisture meter)
E ) Click “+” on the right.
F ) When the check mark appears, click ” Done” to complete the connection.
NOTE:
If necessary, the Bluetooth soil moisture meter can be paired with an
intelligent gateway (Model:TWG009BW) to become a WiFi soil moisture meter for
remote control. The WiFi soil moisture meter can also be paired with a water
timer(Model: TTV102B) for smart watering.
Installing the Soil Moisture Meter
If your soil is soft, insert the device in the “BEST” position.
If your soil is hard, dig a hole and bury the device in the “BEST”
position.
APP INTRODUCTION
APP Home Page
Device Home Page
Select the Bluetooth soil moisture meter to go to the device home page.
There are many data and functions as follows:
- Quickly add
- Switch plants
- Current soil moisture
- Current air temperature
- Celsius degree/ Fahrenheit switching
Plant List
- Add customized plants
- Add a system of plants, there are twenty to choose from.
Customized Settings
- Click here to take a picture or upload a picture of the plant.
- Enter the name of the plant.
- Set the appropriate humidity range for the plant (Refer to the above data when setting).
- Set the appropriate temperature range for the plant (Refer to the above data when setting).
Home Management
- Tap “Me” at the bottom of the APP home screen.
- Select “Home Management”.
- Set your home name, room management and home location.
RESET THE DEVICE
How to reset the Bluetooth soil moisture meter?
Method One:
Remove all batteries from the battery compartment. After 10 seconds, insert 3
fresh AAA(1.5V) alkaline batteries into the battery compartment of the soil
moisture meter, then the green LED indicator quickly flashes (2 times per
second), which means it enters to pairing mode.
Method Two:
Press and hold the button on the soil moisture meter for about 5 seconds until
the green LED indicator quickly flashes(2 times per second), then the
Bluetooth soil moisture meter is restored to pairing mode.
TROUBLESHOOTING
| Problem | Possible Factors | Solution may help |
|---|---|---|
| Data inaccurate or incorrect | Stones around the sensor. | Please ensure that |
there are no stones around the sensor while burying it to avoid any
interference with the accuracy caused by the presence of stones.
No display on the screen| Batteries are low.| Replace brand new alkaline
batteries.
Sensor drains batteries quickly| The cause of the battery itself.|
-
Test a new set of alkaline batteries. Write down the date of installation and the voltage of the batteries. When the batteries fail, please note the date and voltage again.
Check for leaking batteries, which may damage the sensor. -
It is recommended to use reputable brands of alkaline batteries, which can provide a battery life of over 24 months.
Device cannot be connected|
- Distance between device and phone is too far.
- Bluetooth not turned on.
|
- Keep the distance between the phone and soil moisture meter close while connecting.
- Please turn on your phone’s Bluetooth on to pair with the device.
If your Rain Point product does not operate properly after trying the
troubleshooting steps, please contact us by phone or email :
+1-833-381-5659 (US Free Hotline) I
+44-800-808-5337 (UK Free Hotline) I
+49-800-182-0576(DE Free Hotline) I
service@rainpointonline.com
WARRANTY
Rain Point provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship.
-
Warranty service can only be performed by our authorized service center.
The original dated bill of sale must be presented upon request as proof of purchase to us, or our authorized service center. -
To receive warranty service, the purchaser must contact with Rain Point nominated service center for the problem determination and service procedure.
Thank you for your choice of Rain Point products!
FCC Statement (FCC ID: 2AWDBTCS024B)
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:
- This device may NOT cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions. may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception. which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following me-.1sures: -Reorient or relocate
the receiving antenna. -Increase the separation between the equipment and
receiver. -Connect the
equipment into an outlet on a circuit different from that lo which the
receiver is connected. -Consult the dealer or an experienced radio/TV
technician for help. To assure continued compliance, any changes or
modifications not expressly approved by the party.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority lo operate this equipment.
- This equipment complies with Part 15 of the FCC Rules. Operation is subject to
- the following two conditions:
- (1 )This device may not cause harmful interference, and (Z)This device must accept any interference received, including interference
- that may cause undesired operation.
FCC Radiation Exposure Statement:
The equipment complies with FCC Radiation exposure limits set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body
CUSTOMER SERVICE
If you find it difficult to set up and want to watch the setting tutorial
video, please subscribe to our channel “Rain Point” on YouTube.
If the user manual doesn’t have what you’re looking for, and you need some
help, please prepare the LOT NO. of your device and contact us before
returning the product to the store.
LOT NO.: XXXXX (on the back of the meter)
Email :service@rainpointonline.com
WhatsApp: +1 626- 780- 5952
US Free Hot line(English):
+1 833-381 – 5659(MON- FRI 9:30 AM- 5:30 PM PST)
DE Free Hotline(English Deutsch):
+49 800- 182-0576(MON- FRI 9:00 AM- 5:00 PM CET)
UK Free Hotline(English):
+44 800- 808-5337(MON- FRI 9:00 AM- 5:00 PM CET)
EC REP
NAME: VIAJE ELECTRONIC COMPANY LIMITED
ADDRESS: E588, 13 ADELAIDE ROAD, DUBLIN, D02 P950, IRELAND
EMAIL: VIAJEELE@outlook.com
UK REP
NAME: SUJE ELECTRONIC COMPANY LIMITED
ADDRESS: S211 92a Bury Old Road, Manchester, England, M45 6TQ
EMAIL: SUJEELECTRONIC@outlook.com
Manufacturer/Hersteller/Fabricant/Fabricant/Fabricante:
FUJIAN BALDR TECHNOLOGY CO.,LTD
ADDRESS/DIRECCION: Floor 3, Building 2, No.71 Yang qi Road, Fuwan
Industrial Area Cangshan District, Fuzhou, China. 350008
EMAIL:
service@rainpointonline.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>