Ciays MSEDS2B1 Electric Standing Desk Instruction Manual
- June 14, 2024
- CIAYS
Table of Contents
Electric Standing Desk
Instruction Manual
Model:
MSEDS2B1/MSEDS2/MSEDS2N
Specification
Desktop Size: 55.1 x 33.5 in (140x85cm)
Vertical Range: 28.3 – 47.2 in (72-120cm)
Tool Needed (Not included)
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware for Step 2
Supplied Parts and Hardware for Step 3
Supplied Parts for Step 4
Step 1 Assemble the Leg Bases and Crossbar
Pay attention that you need to align the holes on the crossbar with the two outer holes on the metal connector.
Step 2 Secure the Side Plates and Transmission Rod to the Table Legs
How to Solve the Problem of Different Heights of Two Table Legs
Step 1. Measure whether the height of the two table legs are the same
using a measuring tape before installation.
Install Transmission Rod: Please fine-tune the transmission rod.
| Step 3. If the height of the left table leg is lower than the right table
leg, insert the transmission rod into the hexagonal hole of the left table leg
and rotate the transmission rod clockwise to fine-tune the left table leg to
make the left table leg as high as the right table leg.
---|---
| Step 2. If the height of left table leg is higher than the right table leg,
insert the transmission rod into the hexagonal hole of the left leg, then
rotate the transmission rod anti-clockwise to fine-tune the left leg to make
the left table leg as high as the right table leg.
Step 3 Secure the Desktop to the Stand
Step 4 Connect the Cables
Controller Introduction
| Short press the button, the unit will lift 0.39 in (1cm).
Long press the button, the unit will continuously lift unless it reaches to
the highest position of 47.24 in (120cm) or release the button.
---|---
| Short press the button, the unit will lower 0.39 in (1cm).
Long press the button, the unit will continuously lower unless it reaches to
the lowest position of 28.35 in (72cm) or release the button.
| Short press [S] button, the display flashes. Press either of 1,2,3 memory
keys to save the height.
| Press button, and the desk will move to the certain height that was
previously set for memory 1.
| Press button, and the desk will move to the certain height that was
previously set for memory 2.
| Press button, and the desk will move to the certain height that was
previously set for memory 3.
Engineering Mode
Change Displayed Unit ( Un )| Long press the button, “S–’shows and flashes.
Press again and the display shows “ ”. Press to select. Press or to switch
between‘ ‘(metric) or “ ” (imperial). Press to save your choice.
Collision Force Detection (CF)| Long press the button, “S–’shows and flashes.
Press again and the display shows “Un”. Press or to switch to “CF”. Press to
select. Press or to switch between “OFF”, Low (L), Normal (n) or Heavy (H)
collision force detection. Press to save your choice.
Reset| Long press for 5 seconds, and the screen will show RES. Keep Reset
pressing and the desk will go down to the lowest position and
rebound a bit. Reset finished showing basic height.
Protection Mode (auto lock screen mode)
Over-heating protection| Hot: It alarms when continuously working for 2
minutes. Re-powered on and waiting for at least 18 minutes before height
adjustment.
Sensor less alarm| El 0: It alarms when motor sensor can’t be detected.
Power off first. Check the connecting of motor and control box, and then re-
power on.
Overload protection| E20: Overload alarm. If alarming when desk going up,
remove the stuff on the desk and try again. If alarming when desk going down,
power off first, remove the stuff on the desk and re-power on.
Rebound protection| E02: It alarms when vibrated, collided or inclined in desk
moving. Check if there is vibrating, obstacles or incline. If no issues above,
do the reset process and use it again.
Overvoltage alarm| E32: It alarms when voltage is higher than required value.
Power off first. Check whether the connection between power and control box is
OK. Power on again.
Undervoltage alarm| E31: It alarms when voltage is lower than required value.
Power off first. Check whether the connection between power and control box is
OK. Power on again.
Step out alarm| E60: It alarms when height difference between left leg and
right leg exceeds the set value. Power off first. Check whether the left leg
and the right leg are in the same height. If not, re-redo process 4 to make
them in same height. Power on again.
Breaking protection| It stops and enters protection state when motor lines or
manual control lines are removed or disconnected accidentally; back to normal
after reconnected and alarm cleared.
Thank you again for choosing this product!
All of us
do appreciate your product purchase. We hope that you are as happy
with your product as we are designing and manufacturing it for you. We strive
to provide you with the best quality products and services in the industry.
Should you have any issues, please don’t hesitate to contact us
Technical Support:
877-546-8648 Mon-Fri 8am – 8pm(CST)
Other Info: support@ciays.com
860-00048-00 Rev00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>