BenQ LW600ST Projector Installation Guide

BenQ LW600ST Projector

Introduction

The document describes how to control your BenQ projector via RS232 from a computer. Follow the procedures to complete the connection and settings first, and refer to the command table for RS232 commands.

Available functions and commands vary by model. Check the specifications and user manual of the purchased projector for product functions.

Wire arrangement

Wire Arrangement

P1| Color| P2
1| Black| 1
2| Brown| 3
3| Red| 2
4| Orange| 4
5| Yellow| 5
6| Green| 6
7| Blue| 7
8| Purple| 8
9| Gray| 9
Case| Drain wire| Case

RS232 pin assignment

Connections and communication settings

Choose one of the connections and set up properly before RS232 control.

RS232 serial port with a crossover cable

Settings

On-screen images in this document are for reference only. The screens may vary depending on your Operating System, I/O ports used for connection, and the specifications of the connected projector.

1. Determine the COM Port name used for the RS232 communications in Device Manager
   
   

2. Choose Serial and the corresponding COM port as the communication port. In this given example, COM6 is selected.
   

3. Finish Serial port setup.
   Baud rate| 115200 bps (default) Changeable settings in User OSD (9600/14400/19200/38400/57600/115200)
   ---|---
   Data length| 8 bit
   Parity check| None
   Stop bit| 1 bit
   Flow control| None

RS232 via LAN

1. Find the Wired LAN IP address of the connected projector from the OSD menu and make sure the projector and the computer are within the same network.
2. Input 8000 in the TCP port # field.
   

RS232 via HDBaseT

1. Determine the COM Port name used for the RS232 communications in Device Manager.

2. Choose Serial and the corresponding COM port as the communication port. In this given example, COM6 is selected.
   

3. Finish ****Serial port setup.
   

   ---

Baud rate| 115200 bps (default) Changeable settings in User OSD (9600/14400/19200/38400/57600/115200)
---|---
Data length| 8 bit
Parity check| None
Stop bit| 1 bit
Flow control| None

Command table

• Available features differ by projector specification, input sources, settings, etc..
• Commands are working if the standby power is 0.5W or a supported baud rate of the projector is set.
• Uppercase, lowercase, and a mixture of both types of characters are accepted for a command.
• If a command format is illegal, it will echo Illegal format.
• If a command with correct format is not valid for the projector model, it will echo Unsupported item.
• If a command with correct format cannot be executed under certain condition, it will echo Block item.
• If RS232 control is performed via LAN, a command works whether it starts and ends with < CR>. All the commands and behaviors are identical with the control through a serial port.

| Write| Volume +| vol=+#| YES
---|---|---|---|---
Write| Volume –| vol=-#| YES
Write| Volume level for customer| vol=value#| YES
Read| Volume Status| vol=?#| YES
Write| Mic. Volume +| micvol=+#| NO
Write| Mic. Volume –| micvol=-#| NO
Read| Mic. Volume Status| micvol=?#| NO
Audio source select| Write| Audio pass Through off| audiosour=off#| YES
Write| Audio-Computer1| audiosour=RGB#| NO
Write| Audio-Computer2| audiosour=RGB2#| NO
Write| Audio-Video/S-Vide o| audiosour=vid#| NO
Write| Audio-Component| audiosour=ypbr#| NO
Write| Audio-HDMI| audiosour=hdmi#| YES
Write| Audio-HDMI2| audiosour=hdmi2#| YES
Read| Audio pass Status| audiosour=?#| YES
Picture Mode| Write| Dynamic| appmod=dynamic#| NO
Write| Presentation| appmod=preset#| YES
Write| sRGB| appmod=srgb#| YES
Write| Bright| appmod=bright#| YES
Write| Living Room| appmod=livingroom#| NO
Write| Game| appmod=game#| NO
Write| Cinema| appmod=cine#| NO
Write| Standard/Vivid| appmod=std#| NO
Write| Football| appmod=football#| NO
Write| Football Bright| appmod=footballbt#| NO
Write| DICOM| appmod=dicom#| NO
Write| THX| appmod=thx#| NO
Write| Silence mode| appmod=silence#| NO
Write| DCI-P3 mode| appmod=dci-p3#| NO
Write| Vivid| appmod=vivid#| NO
Write| Infographic| appmod=infographic#| NO
Write| Sport| appmod=sport#| NO
Write| Spreadsheet| appmod= spreadsheet #| NO
Write| Bright Room| appmod=brightroom#| NO

| Write| Video| appmod=video#| YES
---|---|---|---|---
Write| Golf| appmod=golf#| YES
Write| User1| appmod=user1#| YES
Write| User2| appmod=user2#| YES
Write| User3| appmod=user3#| NO
Write| ISF Day| appmod=isfday#| NO
Write| ISF Night| appmod=isfnight#| NO
Write| 3D| appmod=threed#| NO
Read| Picture Mode| appmod=?#| YES
Picture Setting| Write| Contrast +| con=+#| YES
Write| Contrast –| con=-#| YES
Write| Set Contrast value| con=value#| YES
Read| Contrast value| con=?#| YES
Write| Brightness +| bri=+#| YES
Write| Brightness –| bri=-#| YES
Write| Set Brightness value| bri=value#| YES
Read| Brightness value| bri=?#| YES
Write| Color +| color=+#| YES
Write| Color –| color=-#| YES
Write| Set Color value| color=value#| YES
Read| Color value| color=?#| YES
Write| Sharpness +| sharp=+#| YES
Write| Sharpness –| sharp=-#| YES
Write| Set Sharpness value| sharp=value#| YES
Read| Sharpness value| sharp=?#| YES
Write| Flesh Tone +| fleshtone=+#| NO
Write| Flesh Tone –| fleshtone=-#| NO
Write| Set Flesh Tone value| fleshtone=value#| NO
Read| Flesh Tone value| fleshtone=?#| NO
Write| Color Temperature-Warmer| ct=warmer#| NO
Write| Color Temperature-Warm| ct=warm#| YES
Write| Color Temperature-Norma l| ct=normal#| YES
Write| Color| *ct=cool#| YES

| | Temperature-Cool| |
---|---|---|---|---
Write| Color Temperature-Cooler| ct=cooler#| NO
Write| Color Temperature-lamp native| ct=native#| YES
Read| Color Temperature Status| ct=?#| YES
Write| Aspect 4:3| asp=4:3#| YES
Write| Aspect 16:6| asp=16:6#| NO
Write| Aspect 16:9| asp=16:9#| YES
Write| Aspect 16:10| asp=16:10#| YES
Write| Aspect 2.4:1| asp=2.4:1#| NO
Write| Aspect Auto| asp=AUTO#| YES
Write| Aspect Real| asp=REAL#| YES
Write| Aspect Letterbox| asp=LBOX#| NO
Write| Aspect Wide| asp=WIDE#| NO
Write| Aspect Anamorphic| asp=ANAM#| NO
Write| Aspect Anamorphic 2.35| asp=ANAM2.35#| NO
Write| Aspect Anamorphic 16:9| asp=ANAM16:9#| NO
Read| Aspect Status| asp=?#| YES
Write| Vertical Keystone +| vkeystone=+#| YES
Write| Vertical Keystone –| vkeystone=-#| YES
Read| Vertical Keystone value| vkeystone=?#| YES
Write| Horizontal Keystone +| hkeystone=+#| YES
Write| Horizontal Keystone –| hkeystone=-#| YES
Read| Horizontal Keystone value| hkeystone=?#| YES
Write| Overscan Adjustment +| overscan=+#| NO
Write| Overscan Adjustment –| overscan=-#| NO
Read| Overscan Adjustment value| *overscan=?#| NO

| Write| 4 Corners Top-Left-X Decrease| cornerfittlx=-#| YES
---|---|---|---|---
Write| 4 Corners Top-Left-X Increase| cornerfittlx=+#| YES
Read| 4 Corners Top-Left-X Status| cornerfittlx=?#| YES
Write| 4 Corners Top-Left-Y Decrease| cornerfittly=-#| YES
Write| 4 Corners Top-Left-Y Increase| cornerfittly=+#| YES
Read| 4 Corners Top-Left-Y Status| cornerfittly=?#| YES
Write| 4 Corners Top-Right-X Decrease| cornerfittrx=-#| YES
Write| 4 Corners Top-Right-X Increase| cornerfittrx=+#| YES
Read| 4 Corners Top-Right-X Status| cornerfittrx=?#| YES
Write| 4 Corners Top-Right-Y Decrease| cornerfittry=-#| YES
Write| 4 Corners Top-Right-Y Increase| cornerfittry=+#| YES
Read| 4 Corners Top-Right-Y Status| cornerfittry=?#| YES
Write| 4 Corners Bottom-Left-X Decrease| cornerfitblx=-#| YES
Write| 4 Corners Bottom-Left-X Increase| cornerfitblx=+#| YES
Read| 4 Corners Bottom-Left-X Status| cornerfitblx=?#| YES
Write| 4 Corners Bottom-Left-Y Decrease| cornerfitbly=-#| YES
Write| 4 Corners| *cornerfitbly=+#| YES

| | Bottom-Left-Y Increase| |
---|---|---|---|---
Read| 4 Corners Bottom-Left-Y Status| cornerfitbly=?#| YES
Write| 4 Corners Bottom-Right-X Decrease| cornerfitbrx=-#| YES
Write| 4 Corners Bottom-Right-X Increase| cornerfitbrx=+#| YES
Read| 4 Corners Bottom-Right-X Status| cornerfitbrx=?#| YES
Write| 4 Corners Bottom-Right-Y Decrease| cornerfitbry=-#| YES
Write| 4 Corners Bottom-Right-Y Increase| cornerfitbry=+#| YES
Read| 4 Corners Bottom-Right-Y Status| cornerfitbry=?#| YES
Write| Digital Zoom In| zoomI#| YES
Write| Digital Zoom out| zoomO#| YES
Write| Auto| auto#| NO
Write| Brilliant color on| BC=on#| NO
Write| Brilliant color off| BC=off#| NO
Read| Brilliant color status| BC=?#| NO
Write| Reset picture settings| rstpicsetting#| YES
Operation Settings| Write| Projector Position-Front Table| pp=FT#| YES
Write| Projector Position-Rear Table| pp=RE#| YES
Write| Projector Position-Rear Ceiling| pp=RC#| YES
Write| Projector Position-Front Ceiling| pp=FC#| YES

| Read| Projector Position Status| pp=?#| YES
---|---|---|---|---
Write| Quick cooling on| qcool=on#| NO
Write| Quick cooling off| qcool=off#| NO
Read| Quick cooling status| qcool=?#| NO
Write| Quick auto search| QAS=on#| YES
Write| Quick auto search| QAS=off#| YES
Read| Quick auto search status| QAS=?#| YES
Write| Menu Position – Center| menuposition=center#| NO
Write| Menu Position – Top-Left| menuposition=tl#| NO
Write| Menu Position – Top-Right| menuposition=tr#| NO
Write| Menu Position – Bottom-Right| menuposition=br#| NO
Write| Menu Position – Bottom-Left| menuposition=bl#| NO
Read| Menu Position Status| menuposition=?#| NO
Write| Direct Power On-on| directpower=on#| YES
Write| Direct Power On-off| directpower=off#| YES
Read| Direct Power On-Status| directpower=?#| YES
Write| Signal Power On-on| autopower=on#| NO
Write| Signal Power On-off| autopower=off#| NO
Read| Signal Power On-Status| autopower=?#| NO
Write| Standby Settings-Network on| standbynet=on#| NO
Write| Standby Settings-Network off| standbynet=off#| NO
Read| Standby Settings-Network Status| standbynet=?#| NO
Write| Standby Settings-Microphone on| *standbymic=on#| NO

| Write| Standby Settings-Microphone off| standbymic=off#| NO
---|---|---|---|---
Read| Standby Settings-Microphone Status| standbymic=?#| NO
Write| Standby Settings-Monitor Out on| standbymnt=on#| NO
Write| Standby Settings-Monitor Out off| standbymnt=off#| NO
Read| Standby Settings-Monitor Out Status| standbymnt=?#| NO
Baud Rate| Write| 2400| baud=2400#| NO
Write| 4800| baud=4800#| NO
Write| 9600| baud=9600#| YES
Write| 14400| baud=14400#| YES
Write| 19200| baud=19200#| YES
Write| 38400| baud=38400#| YES
Write| 57600| baud=57600#| YES
Write| 115200| baud=115200#| YES
Read| Current Baud Rate| baud=?#| YES
Lamp Control| Read| Lamp| ltim=?#| YES
Read| Lamp2 Hour| ltim2=?#| NO
Write| Normal mode| lampm=lnor#| YES
Write| Eco mode| lampm=eco#| YES
Write| SmartEco mode| lampm=seco#| YES
Write| SmartEco mode 2| lampm= seco2#| NO
Write| SmartEco mode 3| lampm= seco3#| NO
Write| LampSave+ mode| lampm= lampsave+#| NO
Write| Dimming mode| lampm=dimming#| NO
Write| Custom mode| lampm=custom#| NO
Write| Light level for custom mode| lampcustom=value#| NO
Read| Light level status for custom mode| lampcustom=?#| NO

| Write(雙 燈)| Dual Brightest| lampm =dualbr#| NO
---|---|---|---|---
Write(雙 燈)| Dual Reliable| lampm =dualre#| NO
Write(雙 燈)| Single Alternative| lampm =single#| NO
Write(雙 燈)| Single Alternative Eco| lampm =singleeco#| NO
Read| Lamp Mode Status| lampm=?#| YES
Miscellaneous| Read| Model Name| modelname=?#| YES
Read| System F/W Version| sysfwversion=?#| YES
Read| Scaler F/W Version| scalerfwversion=?#| NO
Read| Lan F/W Version| lanfwversion=?#| NO
Read| MCU F/W Version| mcufwversion=?#| YES
Read| Ballast F/W Version| ballastfwversion=?#| NO
Write| Blank On| blank=on#| YES
Write| Blank Off| blank=off#| YES
Read| Blank Status| blank=?#| YES
Write| Freeze On| freeze=on#| YES
Write| Freeze Off| freeze=off#| YES
Read| Freeze Status| freeze=?#| YES
Write| Menu On| menu=on#| YES
Write| Menu Off| menu=off#| YES
Read| Menu Status| menu=?#| YES
Write| Up| up#| YES
Write| Down| down#| YES
Write| Right| right#| YES
Write| Left| left#| YES
Write| Enter| enter#| YES
Write| Back| back#| YES
Write| Source Menu On| sourmenu=on#| YES
Write| Source Menu Off| sourmenu=off#| YES
Read| Source Menu Status| sourmenu=?#| YES
Write| 3D Sync Off| 3d=off#| YES
Write| 3D Auto| 3d=auto#| YES
Write| 3D Sync Top Bottom| 3d=tb#| YES
Write| 3D Sync Frame Sequential| *3d=fs#| YES

| Write| 3D Frame packing| 3d=fp#| YES
---|---|---|---|---
Write| 3D Side by side| 3d=sbs#| YES
Write| 3D inverter disable| 3d=da#| YES
Write| 3D inverter| 3d=iv#| YES
Write| 2D to 3D| 3d=2d3d#| NO
Write| 3D nVIDIA| 3d=nvidia#| NO
Read| 3D Sync Status| 3d=?#| YES
Write| Remote Receiver On| rr=on#| NO
Write| Remote Receiver Off| rr=off#| NO
Write| Remote Receiver-front+rear| rr=fr#| NO
Write| Remote Receiver-front| rr=f#| NO
Write| Remote Receiver-rear| rr=r#| NO
Write| Remote Receiver-top| rr=t#| NO
Write| Remote Receiver-top+front| rr=tf#| NO
Write| Remote Receiver-top+rear| rr=tr#| NO
Read| Remote Receiver Status| rr=?#| NO
Write| Instant On-on| ins=on#| NO
Write| Instant On-off| ins=off#| NO
Read| Instant On Status| ins=?#| NO
Write| Lamp Saver Mode-on| lpsaver=on#| NO
Write| Lamp Saver Mode-off| lpsaver=off#| NO
Read| Lamp Saver Mode Status| lpsaver=?#| NO
Write| Projection Log In Code on| prjlogincode=on#| NO
Write| Projection Log In Code off| prjlogincode=off#| NO
Read| Projection Log In Code Status| prjlogincode=?#| NO
Write| Broadcasting on| broadcasting=on#| NO

| Write| Broadcasting off| broadcasting=off#| NO
---|---|---|---|---
Read| Broadcasting Status| broadcasting=?| NO
Write| AMX Device Discovery-on| amxdd=on#| NO
Write| AMX Device Discovery-off| amxdd=off#| NO
Read| AMX Device Discovery Status| amxdd=?#| NO
Read| Mac Address| macaddr=?#| NO
Write| High Altitude mode on| Highaltitude=on#| YES
Write| High Altitude mode off| Highaltitude=off#| YES
Read| High Altitude mode status| *Highaltitude=?#| YES

Note: The above function will be varied from model to model.

FAQ Video

1. How to use RS232 cable to do volume control and sound control on projector?
   https://youtu.be/P4F26kEv60U

2. How to use RS232 cable connection to power on & off projector?
   https://youtu.be/faGUvcDBmJE

3. How to set up RS232 cable connection?
   https://youtu.be/CYJRqyO6K1w

4. How to use RS232 command to request fan speed and temperature value?
   https://youtu.be/KBXEd-BCDKQ

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>