hp C08611076 Anyware Remote Controller System User Guide
- June 16, 2024
- HP
Table of Contents
hp C08611076 Any ware Remote Controller System
HP Anyware Remote System Controller AMO and CTO Offerings
Introduction
The HP Any ware Remote System Controller and HP Any ware Integrated Remote System Controller are remote management peripherals meant to provide out-of- band management to Z Desktop Workstations and select HP Engage Retail Systems. The two different brand names refer to two different form factors of essentially the same product, but with some important differences between the two that are further described later in this document. The HP Any ware Remote System Controller is an external device, and the HP Any ware Integrated Remote System Controller is an internal PCIe device. Both are compatible with most compute devices1 as an IP KVM2 (including Macs) as long as the said compute device has available USB type-A ports and display outputs, but the HP Any ware Remote System Controller (external device) is recommended for use with other compute devices.
Although they are both compatible with other compute devices, users achieve a significantly more advanced feature set when pairing the HP Any ware Remote System Controller or HP Any ware Integrated Remote System Controller with Z by HP Desktop Workstation and select HP Engage Retail Systems.
There are various software methods to interface with the HP Any ware Remote
System Controller and HP Any ware Integrated Remote System Controller to
enable remote management of entire fleets of remote compute devices. These
software methods are described briefly in the ‘Software Overview’ section of
this document, but this document focuses primarily on the hardware devices.
NOTE: When this document refers to both the HP Any ware Remote System
Controller and HP Any ware Integrated Remote System Controller, it may combine
the two as such: HP Any ware (Integrated) Remote System Controller. Remote
System Controller may be abbreviated as RSC.
- HP Any ware Integrated Remote System Controller not compatible with Z2 Mini platforms and not recommended for non-Z devices. HP service and support not available for non-Z devices. Full suite of hardware alerts available with select Z desktop workstations. See datasheet for details.
- IP KVM refers to the ability to remotely interface with the host machine with keyboard, monitor and mouse control over a network.
- Only the Integrated Remote System Controller has been qualified with select HP Engage Retail Systems.
HP Any ware Remote System Controller AMO and CTO Offerings
The HP Any ware Remote System Controller and HP Any ware Integrated Remote System Controller are both available as configure to order (CTO) options on select Z by HP Desktop Workstations and are also available for purchase as an aftermarket option (AMO). See below for which platforms offer CTO options and for a complete list of the after-market options.
CTO Availability:
- HP Z2 Mini G9 (Remote System Controller only, HP Anyware Integrated Remote System Controller not compatible)
- HP Z2 Small Form Factor G9
- HP Z2 Tower G9
- HP Z Central 4R
- HP Z4 G5
- HP Z6 G5
- HP Z8 G5
- HP Engage Flex Pro G2
- HP Engage Flex Pro C G2
NOTE: CTO availability subject to change.
AMO Offerings:
NOTE: For more information on each of the AMO kits below, see the “After
Market Option Kits” part of the ‘Overview’ section in this document
Description | Part Number | Use Case |
---|---|---|
HP Any ware Remote System Controller | 7K6D7AA | AMO kit for use with the |
following platforms:
– Z2 G9 or later
– Z4, Z6, Z8 G4 or later
– Z Central 4R
*For use with the Z Central 4R, Z4 G4, Z6 G4, and Z8 G4, the HP Z4/Z6/Z8 G4 / Z Central 4R Remote System Controller Cable Adapter (7K6E5AA) is required
---|---|---
HP Any ware Remote System Controller for Universal KVM| 7K7N2AA| AMO kit for
non-Z by HP compute devices and Z by HP platforms prior to the systems listed
for 7K6D7AA
HP Z2 Mini Remote System Controller| 7K6E4AA| AMO kit for use specifically
with the HP Z2 Mini G9
HP Any ware Integrated Remote System Controller| 7K6D9AA| AMO kit for the
Integrated Remote System Controller for use with the following platforms:
– Z2 G9 or later (excluding the Z2 Mini)
– Z4, Z6, Z8 G4 or later
– Z Central 4R
*For use with the Z Central 4R, Z4 G4, Z6 G4, and Z8 G4, the HP Z4/Z6/Z8 G4 / Z Central 4R Remote System Controller Cable Adapter (7K6E5AA) is required
HP Any ware Remote System Controller Main Board Adapter| 7K6D8AA| AMO kit for the Z Desktop Power and Signal Interface for allowing external power button enablement and BIOS access to the following platforms:
– Z2 G9 or later (excluding the Z2 Mini)
– Z4, Z6, Z8 G4 or later
– Z Central 4R
*This adapter is already included with 7K6D7AA. This kit does not include the HP Any ware Remote System Controller. This kit is intended for customers who want to share a single Remote System Controller between several devices
HP Z4/Z6/Z8 G4 / Z Central 4R Remote System Controller Cable Adapter| 7K6E5AA|
AMO kit containing the adapter required to use the Remote System Controller
with the Z Central 4R, Z4 G4, Z6 G4, and Z8 G4
HP Any ware Integrated Flex Pro Remote System Controller| 9B141AA| AMO kit
containing the integrated Remote System Controller for use with the HP Engage
Flex Pro G2 and HP Engage Flex Pro C G2
AMO Decoder by Platform:
I Am Using A… | Needed AMO Kit |
---|
- HP Z2 Small Form Factor G9
- HP Z2 Tower G9
- HP Z4 G5
- HP Z6 G5
- HP Z8 G5
- HP Z8 Fury G5
|
-
HP Any ware Remote System Controller (7K6D7AA) for those who want the external form factor
-
HP Any ware Integrated Remote System Controller (7K6D9AA) for those who want the internal form factor
-
HP Any ware Remote System Controller Main Board Adapter (7K6D8AA) for those who just need to add the proprietary 10-pin Z Desktop Power and Signal Interface to their systems. This kit does not include the HP Any ware Remote System Controller itself. This adapter is already included with 7K6D7AA
-
HP Z2 Mini G9
|
- HP Z2 Mini Remote System Controller (7K6E4AA) for those who want the external form factor. The internal form factor is not supported on the Z2 Mini G9
---|---
- HP Z4 G4
- HP Z6 G4
- HP Z8 G4
- HP Z Central 4R
|
-
First purchase the HP Z4/Z6/Z8 G4 / Z Central 4R Remote System Controller Cable Adapter (7K6E5AA) to ensure you have the right adapter and then add either of the below depending on which form factor is desired:
- HP Any ware Remote System Controller (7K6D7AA) for those who want the external form factor
- HP Any ware Integrated Remote System Controller (7K6D9AA) for those who want the internal form factor
-
HP Engage Flex Pro G2
-
HP Engage Flex Pro C G2
|
-
HP Any ware Integrated Flex Pro Remote System Controller (9B141AA)
-
Z by HP Workstation not listed above
-
Workstation or PC from another vendor
-
Mac
-
Server
|
- HP Any ware Remote System Controller for Universal KVM (7K7N2AA). This AMO kit includes all of the necessary components for using the HP Any ware Remote System Controller with a system that doesn’t support the proprietary 10-pin Z Desktop Power and Signal Interface.
HP Any ware Remote System Controller
- LCD Screen
- Host Status LED
- Remote System Controller status LED
- Remote Connection status LED
- Power and Signal Interface (compatible with Z desktops only)
- Mini DisplayPort™ for graphics input
- USB for Mouse/Keyboard/Mass Storage Emulation
- 1GbE Network for Pass Through Ethernet
- Kensington Lock Mount
- 12V DC Power Jack with AC/DC adapter (not needed with Z desktops)
- 1GbE Network for Remote Connection
NOTE: Factory Reset Button is located on the bottom of the Remote System Controller.
Product Part Numbers| 7K6D7AA/7K7N2AA/7K6E4AA (see HP Any ware Remote
System Controller AMO and CTO Offerings section)
---|---
Product Dimensions (LxWxH)| 5.12 x 2.76 x 1.28 in (130 x 70 x 35 mm)
Product Weight| 10.83 ounces (307 grams)
Product Color| Jack Black
Compatibility| As a Universal KVM, all platforms are intended to be
compatible if they can interface with both the DisplayPort™ Input and USB
Input ports.
Power Control, Host Power Status, and Host Power are available with the HP Z4/Z6/Z8 G4 and Z Central 4R platforms when using the HP Z4/Z6/Z8 G4 / Z Central 4R Remote System Controller Cable Adapter (7K6E5AA) and the Main Board Adapter (included in 7K6D7AA or sold separately as 7K6D8AA.1,2
The Z2 G9 and Z4/Z6/Z8 G5 platforms and later all support full compatibility using the kit
7K6D7AA for the HP Any ware Remote System Controller.
Compatible Operating Systems| The HP Any ware Remote System Controller
and accompanying HP Any ware Remote System Management software is compatible
with all operating systems.
Power Supply| Power supply is only included with the HP Any ware Remote
System Controller for Universal KVM (7K7N2AA) AMO kit, to provide power to the
Remote System Controller when power from the host is not available:
Lite On AC to DC Adapter Model: PA-1041-81
Input: 100-240V AC, 50/60Hz 1.2A1 (Cord Length 6 feet or 1.83 meters) Output: 12.0V DC 3.33A (40.0W2) (Cord Length 4 feet or 1.2 meters)3,4
Operating Temperature| Max ambient temperature with AC adapter: 40°C Max ambient temperature without AC adapter: 50°C
- The latest BIOS update is required so the host provides power to the HP Any ware Integrated Remote System Controller in all host power states.
- By installing the HP Z4/Z6/Z8 G4 / Z Central 4R Remote System Controller Cable Adapter (7K6E5AA), power will be stolen from the front USB ports on the host. This was necessary to be able to power the Remote System Controllers in all power states, and it leaves the front USB ports unpowered and unusable.
- The AC power cord is localized to provide compatibility with most countries.
- The expected maximum wattage of the HP Any ware Remote System Controller is 18W with idle power expected in the 4-5W range.
HP Anyware Integrated Remote System Controller
Overview
HP Any ware Integrated Remote System Controller
- Host status LED
- Remote System Controller status LED
- Remote Connection status LED
- USB for Mouse/Keyboard/Mass Storage Emulation1
- Mini DisplayPort™ for graphics input
- 1GbE Network for Remote Connection
- Factory Reset Button
1The front USB Type-A port is not needed if the internal USB 3.0 connector (shown as #2 in Top View) is being used.
- Power and Signal Interface (compatible with Z desktops only)
- Internal USB 3.0 for Mouse/Keyboard/Mass Storage Emulation1
- PCIe Connector2
- The internal USB 3.0 connector is not needed if the front USB Type-A port (shown as #4 in Front View) is being used.
- The function of the PCIe connector is purely electromechanical. No signal is passed over the PCIe bus and the host system will not recognize the HP Any ware Integrated Remote System Controller as a PCIe device.
HP Any ware Integrated Remote System Controller
Product Part Numbers| 7K6D9AA / 9B141AA (see HP Any ware Remote System
Controller AMO and CTO Offerings section)
Product Dimensions (LxWxH)| 4.41 x 2.76 x 0.79 in (112 x 72 x 20 mm)1
Product Weight| 4.46 ounces (126.4 grams)2
Bus Type| PCI Express x43
Compatibility| The HP Any ware Integrated Remote System Controller is
fully compatible with the Z2 G9 and Z4/Z6/Z8 G5 platforms as well as the HP
Engage Flex Pro G2 and HP Engage Flex Pro C G2. When using the HP Any ware
Integrated Remote System Controller with the Z Central 4R and Z4/Z6/Z8 G4
platforms, the HP Z4/Z6/Z8 G4 / Z Central 4R Remote System Controller Cable
Adapter (7K6E5AA) is required to supply auxiliary power to the HP Any ware
Integrated Remote
System Controller, as well as power control, and host power status.4,5
Compatible Operating Systems| The HP Any ware Integrated Remote System
Controller and accompanying HP Any ware Remote System Management software is
compatible with all operating systems.
Operating Temperature| Max ambient temperature: 55°C
---|---
- HP Any ware Remote System Controller only. Dimensions do not include PCIe bracket or cables.
- Weight does not include cables, half-height bracket, or packaging, and is only the HP Any ware Integrated Remote System Controller with the full-height PCIe bracket installed by default.
- The PCIe form factor is purely for power and mechanical retention. No host PCIe signals are used to communicate with the HP Any ware Integrated Remote System Controller as a PCIe device. It is compatible in any generation of PCIe slot as long as the card will physically fit.
- The latest BIOS update is required so the host provides power to the HP Any ware Integrated Remote System Controller in all host power states.
- By installing the HP Z4/Z6/Z8 G4 / Z Central 4R Remote System Controller Cable Adapter (7K6E5AA), power will be stolen from the front USB ports on the host. This was necessary to be able to power the Remote System Controllers in all power states, and it leaves the front USB ports unpowered and unusable.
Comparison Between the Remote System Controller and Integrated Remote System Controller
HP Any ware Remote System Controller| HP Any ware Integrated Remote
System Controller
---|---
- Sits external to the host device (no PCIe slot required)
- Full feature support with Z4, Z6, Z8, Z8 Fury G5 or beyond and Z2 Mini, Z2 Small Form Factor and Z2 Tower G9 or beyond
- Compatible with the Z2 Mini G9
- Not compatible with the HP Engage Flex Pro G2 and HP Engage Flex Pro C G2
- Supports passthrough ethernet
- Universal KVM compatibility with all computers (PC or Mac)
- Requires external power supply when used with non-Z by HP Workstations
- Standard USB and Mini DisplayPort™ recognized by any device
|
- Sits internal to the host device (PCIe slot required)
- Full feature support with Z4, Z6, Z8, Z8 Fury G5 or beyond and Z2 Small Form Factor and Z2 Tower G9 or beyond
- Not compatible with the Z2 Mini G9
- Compatible with the HP Engage Flex Pro G2 and HP Engage Flex Pro C G2
- Does not support passthrough ethernet
- Limited support as a universal KVM (not recommended for use with non-Z by HP Workstations)
After Market Option Kits
7K6D7AA – HP Any ware Remote System Controller
What’s In the Box|
- HP Any ware Remote System Controller
- Main Board Adapter with DB9 adapter bracket
- USB Type-A to Type-A cable (1 meter)
- DisplayPort™ to Mini DisplayPort™ cable (1 meter)
- CAT 5E ethernet cable (1 meter)
- External Power and Signal Interface cable (1 meter)
- Internal Power and Signal Interface cable (38 centimeters)
- Quick Start Guide
---|---
For Use With|
- HP Z2 Small Form Factor G9
- HP Z2 Tower G9
- HP Z4 G5
- HP Z6 G5
- HP Z8 G5
- HP Z8 Fury G5
- HP Z4 G4, HP Z6 G4, HP Z8 G4, and HP Z Central 4R with the addition of 7K6E5AA1
- By installing the HP Z4/Z6/Z8 G4 / Z Central 4R Remote System Controller Cable Adapter (7K6E5AA), power will
the front USB ports on the host. This was necessary to be able to power the Remote System Controllers in all power states, and it leaves the front USB ports unpowered and unusable.
7K7N2AA – HP Any ware Remote System Controller for Universal KVM
What’s In the Box|
- HP Any ware Remote System Controller
- USB Type-A to Type-A cable (1 meter)
- DisplayPort™ to Mini DisplayPort™ cable (1 meter)
- CAT 5E ethernet cable (1 meter)
- Lite On AC to DC Adapter Model: PA-1041-81
- Quick Start Guide
---|---
For Use With|
- Any non-Z by HP compute device
7K6E4AA – HP Z2 Mini Remote System Controller
What’s In the Box|
- HP Any ware Remote System Controller
- Main Board Adapter with Flex Port adapter bracket
- USB Type-A to Type-A cable (30 centimeter)
- DisplayPort™ to Mini DisplayPort™ cable (30 centimeter)
- CAT 5E ethernet cable (30 centimeter)
- Power and Signal 10pin RSC cables for Z2 Mini
---|---
|
- Quick Start Guide
---|---
For Use With|
- HP Z2 Mini G9
7K6D9AA – HP Any ware Integrated Remote System Controller
What’s In the Box|
- HP Any ware Integrated Remote System Controller with PCIe Half-Height Bracket and QR Code Label with unique identifiers and default password
- External USB Type-A to Type-A cable (30 centimeters)
- Internal USB cable (37 centimeters)
- DisplayPort™ to Mini DisplayPort™ cable (30 centimeters)
- Internal Power and Signal Interface cable (38 centimeters)
- Quick Start Guide
---|---
For Use With|
- HP Z2 Small Form Factor G9
- HP Z2 Tower G9
- HP Z4 G5
- HP Z6 G5
- HP Z8 G5
- HP Z8 Fury G5
- HP Z4 G4, HP Z6 G4, HP Z8 G4, and HP Z Central 4R with the addition of 7K6E5AA1
- By installing the HP Z4/Z6/Z8 G4 / Z Central 4R Remote System Controller Cable Adapter (7K6E5AA), power will be stolen from the front USB ports on the host. This was necessary to be able to power the Remote System Controllers in all power states, and it leaves the front USB ports unpowered and unusable.
9B141AA– HP Any ware Integrated Flex Pro Remote System Controller
What’s In the Box|
- HP Any ware Integrated Remote System Controller with PCIe Half-Height Bracket and QR Code Label with unique identifiers and default password
- External USB Type-A to Type-A cable (30 centimeters)
- DisplayPort to Mini DisplayPort cable (30 centimeters)
- Internal Power and Signal Interface cable (120 millimeters)
- Quick Start Guide
---|---
For Use With|
- HP Engage Flex Pro G2
- HP Engage Flex Pro C G2
7K6D8AA – HP Any ware Remote System Controller Main Board Adapter
What’s In the Box| · Main Board Adapter with DB9 adapter bracket1
· External Power and Signal Interface cable (1 meter)
· Internal Power and Signal Interface cable (38 centimeters)
---|---
For Use With|
- HP Z2 Small Form Factor G9
- HP Z2 Tower G9
- HP Z4 G5
- HP Z6 G5
- HP Z8 G5
- HP Z8 Fury G5
- HP Z4 G4, HP Z6 G4, HP Z8 G4, and HP Z Central 4R with the addition of 7K6E5AA2
- Main Board Adapter max ambient temperature: 65°C.
- By installing the HP Z4/Z6/Z8 G4 / Z Central 4R Remote System Controller Cable Adapter (7K6E5AA), power will be stolen from the front USB ports on the host. This was necessary to be able to power the Remote System Controllers in all power states, and it leaves the front USB ports unpowered and unusable.
7K6E5AA – HP Z4/Z6/Z8 G4 / ZCentral 4R Remote System Controller Cable Adapter
What’s In the Box|
- PCIe Full-Height Bracket for the Main Board Adapter
- HP Z4/Z6/Z8 G4 / Z Central 4R Remote System Controller Cable Adapter
- Power and Signal 10pin RSC cable
---|---
For Use With 1,2|
- HP Z4 G4
- HP Z6 G4
- HP Z8 G4
- HP Z Central 4R
- The latest BIOS update is required so the host provides power to the HP Any ware Integrated Remote System Controller in all host power states.
- By installing the HP Z4/Z6/Z8 G4 / Z Central 4R Remote System Controller Cable Adapter, power will be stolen from the front USB ports on the host. This was necessary to be able to power the Remote System Controllers in all power states, and it leaves the front USB ports unpowered and unusable.
Manageability Features
The below list is a high-level summary of the manageability features that the HP Any ware (Integrated) Remote System Controller enables when paired with Z2 platforms G9 and beyond, and Z4, Z6, Z8, or Z8 Fury G5 and beyond. For an understanding of how these features differ when paired with other compute devices, see the “Feature Comparison by Platform” chart in the ‘Technical Specifications’ section. New features are consistently added to the HP Any ware (Integrated) Remote System Controller through either the embedded software or HP Any ware Remote System Management software (see ‘Software Overview’ section), so this list may not represent all of the capabilities.
- IP KVM Remote Console (including pre-boot access)
- Direct Communication with BIOS
- Power Button Control
- Hardware Alerts
- Hardware System Inventory
- BareMetal Imaging
- Firmware Updates
- Remote Virtual Storage
- Agentless Management
After Market Option Kits
Introduction
There are three primary ways to interface with the HP Any ware Remote System Controller and HP Any ware Integrated Remote System Controller:
Overview
- Embedded software
- HP Any ware Remote System Management
- Redfish® API
The following section will outline these three methods and give basic instructions. For further information, please seek out software specific user guides online.
Embedded Software
Each HP Any ware (Integrated) Remote System Controller has a web server that
can be accessed directly from a web browser. This method of interfacing with
the hardware is for managing one device at a time and can be viewed as
containerized micro-services running on an Ubuntu 18.04 Linux Kernel.
To access the embedded software, it is required to be on the same network that
the HP Any ware (Integrated) Remote System Controller is assigned to.
Instructions for Accessing the Embedded Software
-
Open a web browser. Any web browser will work, but the experience is optimized for Google Chrome.
-
Enter either the IP address or serial number for the HP Any ware (Integrated) Remote System Controller being accessed.
a. For the HP Any ware Remote System Controller, the IP address will be displayed on the front LCD screen. The serial number can be found on the underside of the Remote System Controller.
b. For the HP Any ware Integrated Remote System Controller, the serial number can be found on the sticker on the top side of the card. -
Login to the embedded software using the default username “Admin” and the default password for the HP Any ware (Integrated) Remote System Controller.
a. For the HP Any ware Remote System Controller, the password can be found on the underside of the Remote System Controller.
b. For the HP Any ware Integrated Remote System Controller, the password can be found on the sticker on the top side of the card.
NOTE: The password can be changed from the embedded software UI after the first login.
HP Any ware Remote System Management
The HP Any ware Remote System Management is a subscription, public-cloud software that enables fleet management from a single console. It is planned to be commercially available in late 2023, but alpha testing is available for those interested.
Redfish® API
Redfish® is a communication protocol usually used for the management of servers. The HP Any ware (Integrated) Remote System Controller uses this same communication protocol so it can fit seamlessly within server environments and take advantage of many of the same software scripts that are used in server management. For more information, please seek out Redfish® API documentation online.
For more information, please visit DMTF’s Redfish® site:
https://www.dmtf.org/standards/redfish
Technical Specifications
HP Any ware Remote System Controller – Technical Specifications
System-on-Module (Some) NVIDIA® Jetson Nano
CPU Quad-core ARM Cortex-A57 MP Core processor
GPU NVIDIA® Maxwell with 128 NVIDIA® CUDA® cores
Memory 4GB 64-bit LPDDR4, 1600MHz 25.6 GB/s
Storage 16GB eMMC 5.11
Upgradeable Storage used Slot (SD4.0)2
Ethernet 10/100/1000Mbps (all ports)
maps Input 1920×1200 60Fps
USB USB3.1G1 (5Gbps)
TPM TPM2.0 SLB9672
Power ~4W (Idle)/~17W (Max)
Power Supply Power supply is only included with the HP Any ware Remote
System Controller for Universal KVM
(7K7N2AA) AMO kit, to provide power to the Remote System Controller when power
from the host is
not available:
LiteOn AC to DC Adapter Model: PA-1041-81
Input: 100-240V AC, 50/60Hz 1.2A1 (Cord Length 6 feet or 1.83 meters)
Output: 12.0V DC 3.33A (40.0W2) (Cord Length 4 feet or 1.2 meters)3
Thermal Active Cooling
Operating Max ambient temperature with AC adapter: 40°C
Temperature Max ambient temperature without AC adapter: 50°C
- Virtual Media storage capacity is 4.7GB.
- For later expandable storage.
- The AC power cord is localized to provide compatibility with most countries.
HP Any ware Integrated Remote System Controller – Technical Specifications
System-on-Module (Some) NVIDIA® Jetson Nano
CPU Quad-core ARM Cortex-A57 MP Core processor
GPU NVIDIA® Maxwell with 128 NVIDIA® CUDA® cores
Memory 4GB 64-bit LPDDR4, 1600MHz 25.6 GB/s
Storage 16 GB eMMC 5.11
Upgradeable Storage used Slot (SD4.0)2
Ethernet 10/100/1000Mbps
maps Input 1920×1200 60Fps
USB USB3.1G1 (5Gbps)
TPM TPM2.0 SLB9672
Power ~4W (Idle)/~17W (Max)
Thermal Active Cooling
Operating Max ambient temperature: 55°C
Temperature
- Virtual Media storage capacity is 4.7GB.
- For later expandable storage.
Feature Comparison by Platform
Feature| Z4, Z6, Z8, Z8 Fury G5+ Z2 G9+
HP Engage Flex Pro G2 & **Flex Pro C G2**
| Z4, Z6, Z8 G4
Z Central 4R 1
| Non-Z Compute Devices
---|---|---|---
Technical Specifications
Power Button Control| ⬤| ⬤|
---|---|---|---
Direct Communication with BIOS| ⬤| |
BareMetal Imaging| ⬤| Manual| Manual
Remote Virtual Storage| ⬤| ⬤| ⬤
IP KVM2| ⬤| ⬤| ⬤
HW System Inventory| ⬤| |
Hardware Alerts| ⬤| Partial3|
HP Any ware (Integrated) Remote System Controller
Firmware Updates
| ⬤| ⬤| ⬤
- By installing the HP Z4/Z6/Z8 G4 / Z Central 4R Remote System Controller Cable Adapter (7K6E5AA), power will be stolen from the front USB ports on the host. This was necessary to be able to power the Remote System Controllers in all power states, and it leaves the front USB ports unpowered and unusable.
- IP KVM refers to the ability to remotely interface with the host machine with keyboard, monitor and mouse control over a network.
- By being able to communicate directly with the BIOS when paired with Z2 platforms G9 and beyond, or Z4, Z6, Z8, and Z8 Fury G5 and beyond, the HP Any ware (Integrated) Remote System Controller is able to reactively alert users of over 200 different hardware events. When paired with the Z4 G4, Z6 G4, Z8 G4, or Z Central 4R, the hardware events that the HP Any ware (Integrated) Remote System Controller is able to detect is limited only to events that prevent the system from booting.
Security Features
- Zero Trust Model: All communication is over HTTPS with scion -bossed tokens, multi-factor authentication, and secure web sockets.
- Trusted Platform Module: The HP Any ware (Integrated) Remote System Controller uses the same TPM 2.0 chip that Z by HP Desktop Workstations use. They are Common Criteria EAL4+ certified.
- Full-Disk Encryption: All data is encrypted at rest, using secure boot to ensure that only HP-signed bits can be loaded.
- HP Labs Security Libraries: The HP Any ware (Integrated) Remote System Controller and HP Any ware Remote System Management utilizes libraries developed by HP Labs to enable the highest level of encryption with redundancy and futureproofing.
- Physical Security: The HP Any ware Remote System Controller features a Kensington lock slot.
Service, Support, and Warranty
On-site Warranty and Service1 : Warranty term is determined by the purchase path. When bundled CTO with a Z by HP Workstation or select HP Engage Retail System, the HP Any ware (Integrated) Remote System Controller will absorb the warranty of the Workstation. When purchased as an after market option, the HP Any ware (Integrated) Remote System Controller has a one-year, limited warranty. Service offering delivers on-site, next business-day2 service for parts and labor and includes free telephone support3 8am – 5pm. Global coverage ensures that any product purchased in one country and transferred to another, non restricted country will remain fully covered under the original warranty and service offering. 24/7operation will not void the HP warranty.
Note 1: Terms and conditions may vary by country. Certain restrictions
and exclusions apply
Note 2: On-site service may be provided pursuant to a service contract
between HP and an authorized HP third-party provider, and is not available in
certain countries. Global service response times are based on commercially
reasonable best effort and may vary by country.
Note 3: Technical telephone support applies only to HP-configured, HP and
HP-qualified, third-party hardware and software.
Toll-free calling and 24×7 support service may not be available in some
countries.
HP Care Pack Services extend service contracts beyond the standard warranties.
Service starts from date of hardware purchase.
To choose the right level of service for your HP product, use the HP Care Pack
Services Lookup Tool at:
Technical Specifications
http://www.hp.com/go/lookuptool. Service levels and response times for HP Care Packs may vary depending on your geographic location.
Certifications and Compliance
Environmental Sustainability questions concerning:
- Ecolabels (EPEAT, TCO, etc.)
- ENERGY STAR, California Energy Commission (CEC)
- Compliance with Environmental legislation (EU ErP, China CECP, EU RoHS, and other countries)
- Supply Chain Social Environmental Responsibility (SER) (conflict mineral; human rights, etc.)
- Product specific environmental features (material content, packaging content, recycled content, etc.)
- China Energy Label (CEL)
Please contact sustainability@hp.com
For country specific Regulatory Compliance approval documents or Regulatory
and Safety questions concerning:
- Declarations of Conformity (for self-service, go to https://www.hp.com/uken/certifications/technical/regulationscertificates.html?jumpid=ex_r135_uk/en/any/corp/hpukmu_chev/certificates)
- GS Certificates
- Product Safety Certificates (UL, CB, BIS, etc.)
- EMC Certificates, Declarations of Conformity, or Certificates of Conformity (CE, FCC, ICES, etc.)
- CCC Certificates
- Ergonomics
Please contact techregshelp@hp.com
Date of change: | Version History: | Description of change: | |
---|---|---|---|
January 1, 2024 | From v1 to v2 | Changed | Introduction, HP Any ware Remote |
System Controller AMO and CTO Offerings, HP Any ware Integrated Flex Pro Remote System Controller, Feature Comparison by Platform, Service, Support, and Warranty sections
© 2023 HP Development Company, L.P. The information contained herein is
subject to change without notice.
The only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing herein
should be construed as constituting an additional warranty. HP shall not be
liable for technical or editorial errors or omissions contained herein. NVIDIA
and the NVIDIA logo are trademarks and/or registered trademarks of NVIDIA
Corporation in the U.S. and other countries. SD is a trademark or registered
trademark of SD-3C in the United States, other countries, or both.
DisplayPort™ and the DisplayPort™ logo are trademarks owned by the Video
Electronics Standards Association (VESA®) in the United States and other
countries. USB Type-C® and USB-C® are trademarks of USB Implementers Forum.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>