MeTra CS-HDC5EXT4KPOE HDMI Extender User Manual

MeTra CS-HDC5EXT4KPOE HDMI Extender

Important Safety Instructions

1. Do not mix up HDMI to RJ45 sender and RJ45 to H DMI receiver before installation.
2. Do not hot plug when it is working.
3. Use DCSV power supply only. Make sure specification matched if using adapters not supplied supplied by factory.

Introduction

This HDMI Extender includes a transmitter unit and a receiver unit, allows HDMI signal to be transmitted up to 60 meters at 4Kx 2K@30Hz, and up to 30 meters at 4Kx2K@60Hz long away via a single CAT6/6A/7 cable in a point-to- point configuration. It supports IR pass back with a wide IR frequency 20-60KHz. It is perfect for application of outdoor advertising, video clips, monitor system, home entertainment and conference, etc

Features

1. Support HDMI2.0, compatible with HDCP2.2
2. Highest resolution support 4Kx2K@60Hz
3. Transmission over single CAT6/6A/7
4. Support IR pass back function (IR range support 20—60KHz)
5. Support distance up to 60m
6. Plug and play
7. Metal casing, stable and durable

Package Contents

• Transmitter unit x 1pcs

• Receiver unit x1pcs

• DC5V/1A *1pcs

• User manual *1pcs

• IR blaster extension cable x1pcs

• IR receiver extension cable x1pcs

Installation Requirements

1. HDMI source device (compute graphics card, DVD, PS3, )HD monitoring equipment etc.
2. HDMI display device like SDTV, HDTV, projector with HDMI port.
3. UTP/STP cat6/cat6A/cat7 cable. Follow standard IEEE-568B.

Interfaces

Transmitter unit(TX)

Receiver unit (RX)

Installation Procedures

1. How to make a Cat6 network cable?
   Follow the standard of IEEE-568B:

2. 0range/white
   

3. 0range
   

4. Green/white
   

5. Blue
   

6. Blue/white
   

7. Green

8. Brown/white
   

9. **Brown

**

2. **Connection

**

3. Connection instruction

1. Connect source device to Transmitter unit (TX), and display device to Receiver unit (RX) via H DMI cables.
2. Connect Transmitter unit (TX) and Receiver unit (RX) via network cables (CAT6,CAT6A or CAT7).
3. Plug the power supply to Transmitter unit only, each unit will power up then initialize itself, this HDMI extender works.

4. IR User Guide
   1) IR blaster extension cable should plug in the IR OUT port of TX (Sender) of HDMI extender, and the IR receiver extension cable should plug in the IR IN port of the Video wall controller.

2. The emitter of IR blaster should as close as possible to the IR receiver window of the signal source device.
3. Using the IR remote controller of the signal source device towards the IR receiver (connected to the Video wall controller), to remote control source media playback.

FAQ

There is no output on screen when all connections are correct?

A: 1) Please check and make sure the display/monitor supports the HDMI signal which fed out from the source device. 2) Please make sure the H DMI cables supports 4Kx 2K if the output signal from the source device is 4Kx2K resolution. 3) Please check and make sure the network cable insert to the RJ45 port well. 4) Restart the transmitter or receiver by pressing the reset button.

Q: Black screen happened on the display/monitor?

A: 1) Please check and make sure the length of the network cable within the usable range: CAT6 within 60m@4Kx 2K@30Hz, CAT6 within 30m@4Kx2K@60Hz 2) Reset the transmitter unit for re-built the connection

Q: The color comes abnormity or there is no audio output?

A:Reset the transmitter unit for re- built the connection

Specification

Protection Level Electrostatic protection of the whole machine Operating Environment Working temperature  Body Properties Dimension Reliability Mean time between failures(MTBF)

1080i@50/ 60Hz, 1080p@50/ 60Hz 4Kx2K 24/25/30/ 60/Hz
Supports audio formats| PCM
Maximum transfer rate| 10.2Gbps
Input and output TMDS signal| 0.5 ~ 1.5Vp-p(TMDS)
Input and output DOC signal| 5Vp-p(TTL)
Input cable length| 58m(AWG24)
Output cable length| 58m(AWG24)
Protection Level| Electrostatic protection of the whole machine| 1a Contact discharge level 3 lb Air discharge level 3 Implementation of the standard: IEC61000-4-2
Operating Environment| Working temperature| 0~ 50°C
Storage temperature| -10~ 10°c
Fumidity (no condensation)| 0~90%
Body Properties| Dimension| 77.49(L) x 56.5(W) x 22.66(H)mm
Material| Aluminium alloy material + crystal panel
Treatment process| Grit blast
Color| Black
Weight| TX:80g, RX:80g
Reliability| Mean time between failures (MTBF)| >30000 Hours

Disclaimer

The product name and brand name may be registered trademark of related manufacturers.TM and® may be omitted on the user manual. The pictures on the user manual are just for reference, and there may be some slight difference with the real products. We reserve the rights to make changes without further notice to a product or system described herein to improve reliability, function or design.

CUSTOMER SERVICES

MetraHomeTheater.com
866-839-9187
460 Walker Street
Holly Hill, FL 32117-2653
©2018 Metra Electronics Corporation
Designed and Manufactured to
Metra Home Theater Group Specifications MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>