DAYBETTER DBA0616017 White LED Strip Lights User Manual

DAYBETTER DBA0616017 White LED Strip Lights

Product Information

Specifications:

• Color temperature presets: 2700K, 3200K, 4000K, 5000K, 5500K, 6000K
• Supports custom color temperature adjustment
• 5 dynamic modes: flashing mode, gradient mode, jump mode
• 2 breathing modes
• Sunrise Mode: transition from warm white to positive white
• Sunset Mode: reverse of Sunrise Mode
• Night Mode: minimum brightness
• Touch control function
• RF remote control
• Power-off memory function

Product Usage Instructions

• Controller Connection:
  • Connect the arrow of the light strip to the +12V connection.
  • Connect the receiver to the DC wire.
• Surfaces Installation:

1. Ensure that the controller connection is properly set up.
2. Use the RF remote control to turn on and operate the lights.
3. Pull out the transparent chip from the bottom of the RF remote to ensure proper battery power.

RF Remote Controller Indication:

• ON BUTTON: Turn on the lights.
• OFF BUTTON: Turn off the lights.
• Color temperature/speed adjustment (minus): Adjusts the color temperature or speed downwards.
• Color temperature/speed adjustment (plus): Adjusts the color temperature or speed upwards.
• Timing: Automatically turns off the lights after 60 seconds.
• Color temperature presets: 2700K, 3200K, 4000K, 5000K, 5500K, 6000K.
• Support custom color temperature adjustment: Use the color temperature plus and minus keys to adjust the color temperature.
• LED brightness adjustment button (up): Increases the LED brightness.
• LED brightness adjustment button (down): Decreases the LED brightness.
• Sunrise Mode: Slowly transitions from warm white to positive white over 4 minutes.
• Sunset Mode: The reverse of Sunrise Mode.
• Night Mode: Keeps a minimum brightness.

Touch Control:
The touch function is turned on by default and can be turned off by remote control:

• To turn off the touch function, press the OFF key five times continuously.
• To turn on the touch function, press the ON key five times in a row.

What you can do with touch:

1. Turn on and turn off the light: Just a short touch once.
2. Switch color temperature: When touch to turn on, if within 2 seconds you touch again, the color temperature will switch.
3. Adjust brightness smoothly: Long touch. The brightness will smoothly change between max and min value. Always starts with decline first.

Tips for Using RF Remote Control:

• When the controller is not paired with any RF remote controller, it can be controlled by multiple RF remote controllers.
• When paired, the controller is only controlled by the paired remote controller.
• One remote controller can be paired with multiple controllers.

Pairing Operation Method:

• Pairing:
  • Turn on the light.
  • Press and hold the ON button on any remote control for 2 seconds.
  • The white light will flash twice to indicate successful pairing.
• Unpairing:
  • Turn on the light.
  • Press and hold the OFF button on the bound remote control, or power on and off 3 times in succession to unpair.
  • The device will begin to flash white light continuously.
  • After unpairing, you can long press the ON button of the remote control you want to pair.

FAQ:

• Q: What color temperature presets are available?
  A: The available color temperature presets are 2700K, 3200K, 4000K, 5000K, 5500K, and 6000K.

• Q: Can I adjust the custom color temperature?
  A: Yes, you can adjust the custom color temperature using the color temperature plus and minus keys.

• Q: How many dynamic modes are supported?
  A: There are 5 dynamic modes supported: flashing mode, gradient mode, jump mode, and 2 breathing modes.

• Q: Can I adjust the brightness and speed in all dynamic modes?
  A: In most dynamic modes, you can adjust both the brightness and speed. However, in the 2 breathing modes, only the speed can be adjusted, and the brightness remains constant.

• Q: What is the Sunrise Mode?
  A: The Sunrise Mode slowly transitions the light from warm white to positive white over more than 4 minutes. The brightness and speed cannot be adjusted in this mode.

• Q: Is there a Sunset Mode?
  A: Yes, the Sunset Mode is the reverse of the Sunrise Mode. It transitions the light from positive white to warm white. The brightness and speed cannot be adjusted in this mode.

• Q: What is Night Mode?
  A: Night Mode keeps the light at a minimum brightness. The brightness and speed cannot be adjusted in this mode.

• Q: Can I turn off the touch function?
  A: Yes, you can turn off the touch function by pressing the OFF key five times continuously on the remote control. To turn it back on, press the ON key five times in a row.

• Q: Does the controller have a power-off memory function?
  A: Yes, the controller supports the power-off memory function. After power-off and then power-on, the light strip will continue in the previous state. The controller stores the current state of the device after 9 seconds of touch operation or remote control.

• Q: Can I control multiple controllers with one remote control?
  A: Yes, one remote controller can be paired with multiple controllers. However, when a controller is paired with a remote control, it can only be controlled by that specific remote control.

PACKAGE CONTENTS

CONNECTION

Please spread out the light strip before connecting the power supply.

INSTALLATION

Installation Steps

• STEP 1: Connect the arrow of the light strip to +12V.

• STEP 2: Connect the receiver to the DC wire.

• STEP 3: Tear off the plastic on the adhesive tape and stick the strip to any smooth, clean and dry Surfaces.
  Please be careful not to tear off the adhesive tape.
  Please make sure the surface smooth, dry, clean. DO NOT stick the led strip on the surface, such as knitted / wool fabrics, dust wall, rough plastic suface, frosted glass.

• STEP 4: Stick the LED strip and press with force, and then press the whole LED strip repeatedly.

• STEP 5: Installation finished. Use the RF remote to turn on and operate the lights.
  Please pull out the transparent chip from the bottom of the RF remote to ensure that the battery is powered properly.

RF REMOTE CONTROLLER INDICATION

17-Key

1. ON BUTTON
2. OFF BUTTON
3. Color temperature/speed adjustment (minus)
4. Color temperature/speed adjustment (plus)
5. Timing: Automatically turn off the lights after 60seconds
6. Color temperatures (6 preset) 2700K, 3200K, 4000K, 5000K, 5500K, 6000K. Support custom color temperature adjustment:
7. LED brightness adjustment button(up)
8. 5 dynamic modes:
9. Supports 1 flashing mode, and 1 gradient mode, supports 1 jump mode, and can adjust brightness and speed.
10. Support 2 breathing modes, only the speed can be adjusted, and the brightness cannot be adjusted.
11. LED brightness adjustment button (down) than 4 in este some tension son a positive write the interest the site cranes beamed.
12. Sunset Mode: The reverse of Sunrise Mode. The brightness and speed cannot be adjusted.
13. Night Mode: Keep a minimum brightness. The brightness and speed cannot be adjusted.

Note: This product complies with FCC rules, the FCC ID number is 2A7WU-22303.

TOUCH CONTROL

The touch function is turned on by default and can be turned off by remote control: press the OFF key five times continuously to turn off the touch function. Press the ON key five times in a row to turn on the touch function.

What you can do with touch:

1. Turn on and turn off light.
   • Just a short touch once.
2. Switch color temprature.
   • When touch to turn on, if within 2 seconds you touch again, the color temperature will switch.
3. Adjust brightness smoothly.
   • Long touch. The brightness will smoothly change between max and min value. Always starts with a decline first.

State Memory:
Support power-off memory, that is, after power-off and then power-on, the light strip will continue to the previous state, and the controller will store the current state of the device after 9 seconds of touch operation or remote control.

TIPS OF USE RF REMOTE CONTROL

• When the controller is not paired with any RF remote controller, it can be controlled by multiple RF remote controllers;
• When paired, the controller is only controlled by the paired remote controller;
• One remote controller can be paired with multiple controllers.

PAIRING OPERATION METHOD

1. Pairing: When the controller is not bound to a remote control, turn on the light, press and hold the ON button on any remote control for 2 seconds, and the white light will flash twice to indicate successful pairing.
2. Unpairing: Turn on the light, Press and hold the OFF button on the bound remote control, or power on and off 3 times in succession to unpair, and the device will begin to flash white light continuously. After unpairing, you can long press the ON button of the remote control you want to pair.
   • RF remote control binding indicator light effect: white light flashes twice. (Only after successful binding)
   • RF remote control unbinding indicator light effect: white light flashes continuously. (Only after unbinding)

SAFETY TIPS

1. Please ensure the power is off before wiring and installation.
2. The supply voltage of this product is DC 12V never connected to DC 24V or AC 220V.
3. Never connect two wires directly in case of short circuit.
4. To ensure normal work of the strip, please use the voltage indicated on the packing.
5. If the power supply is damaged, do not attempt to repair it yourself. Please leave it to a professional technician to deal with.
6. Please do not use this product in the open air or under a humid environment.
7. To avoid any damage to the strip, please do not use chemical solvents during routine maintenance.

CONTACT US
If you have any questions or product issues, please contact seller via the email on the package or get the product support on the order page in your purchasing account. All messages will be replied within 24 hours.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>