Kwikset UNT1 1000 Series Deadbolt Smart Lock User Guide

Kwikset UNT1 1000 Series Deadbolt Smart Lock

1000 SERIES DEADBOLT SMART LOCK

Installation and User Guide

Required tools

• Kwikset
• Technical Support
  • 1-800-327-5625
  • www.kwikset.com

1. Prepare the door and check dimensions
   If drilling a new door, use the supplied template and the complete door drilling instructions available at www.kwikset.com/doorprep.

2. Measure to confirm that the hole in the door is either 2-1/8 in (S4 mm) or 1-tnin(38mm).
   Note: Addition door preparation may be required for door with 1-ln in(38mm) holes. Consult the deadbolt drilling instructions .1it www.kwikset.com/doorprep.

3. Measure to confirm that the backset is either 2·3/8 or 2-3/4 in (60 or 70 mm).

4. Measure to confirm that the hole in the door edge is 1 in (25 mm).

5. Measure to confirm that the door is  between 1-3/8 and 1-3/4 in (35 mm and 44mm)thick
   Note: Please contact customer save if door thickness exceeds 1-3/4 in for a thick door kit

6. Install the latch and strike

7. Hold the latch in front of the door hole, with the latch face flush against the door edge.

8. Is the rectangular shaped hole centered in the door hole?

9. Is the door edge chiseled with round or square comers?

10. Which latch face are you installing?

11. Install strike on the door frame.
    Make sure the hole in the door frame is drilled a minimum of 1 in (25 mm) deep .

12. Install the exterior assembly

    • What is the diameter of the hole in the door?
    • To remove adapter for 1-1/2 in (38 mm)diameter
    • Locate screws for step 3D and keep them within reach.
    • Install exterior assembly and interior chassis.
    • Install exterior assembly and interior chassis.
    • Install exterior assembly. Route cable underneath the latch bolt.
    • Install mounting plate.

13. Install the interior assembly

14. Remove interior cover from interior assembly.
    Check to make sure the latch bolt is in the ret reacted/ unlocked position to install the interior assembly
    Make sure turn piece shaft is horizontal as shown
    Remove the interior cover from the interior assembly.

15. Install interior assembly onto mounting plate.
    Connect cable wire as shown. Ensure tight cable connection.
    Route excess cable around the side notch and bottom of the interior assembly.
    Insert the flat blade into the turnpiece shaft.

16. Install the batteries in the interior assembly

17. Install 4 AA batteries in interior assembly

18. Install interior cover for the interior assembly

19. Test the lock.

Reference Guide

Manual Factory reset

1. Insert battery to power up the lock.
2. Status/Programming LED light displays GREEN 3s. Rotate the interior turnpiece back and forth 3x within Ss.
3. Wait for pro gamming LED light to alternate BLUE a nd RED continuously.
4. Within 1 Os, rotate the interior turnpiece back and forth 3x.
5. Program LED light will display solid GREEN for a successful manual factory reset.
6. Fail/Timeout all LED lights will remain off

Low Battery

• If the 4 AA batteries are too low to operate the lock. use a 9-Volt alkaline battery to temporarily power the lock.
• Make sure both terminals on the 9-Volt battery touch the terminals below the turnpiece. Hold t he 9-Volt in
• place while holding the credential on the exterior of the lock. Hold the 9-Volt battery as well as the credential until the lock illuminates and unlocks.
• WARNING: Change batteries immediately otherwise the lock will remain unlocked

Regulatory Compliance

• This product complies with standards established by the following regulatory bodies:
• Federal Communications Commission (FCC) Industry Canada

FCC

This device’s wireless operation is safe and complies with RF Exposure requirements. This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
• Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation

This equipment generates, uses, and can radiate radio frequency energy and, if no t installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception,  which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one  or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver
  • Connect the equipment into an outlet on a circuit different from that to which t he receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help

IMPORTANT! Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate t he equipment. Industry Canada
This device complies with Industry Canada licence exempt RSS standard(s).

Operation is subject to the following two conditions

1. This device may not cause interference, and
2.  This device must accept any interference, including interference that may cause undesired operation of the device

• FCC ID, NUL-Until
• IC 3022A-UNT1
  • e 2023 Spectrum Brands, Inc

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>