FreedConn BL06.0050.0633 Motorcycle Bluetooth Headset with Camera User Manual

FreedConn BL06.0050.0633 Motorcycle Bluetooth Headset with Camera User Manual

Welcome

Thank you for choosing FreedConn Helmet Bluetooth® Intercom system. By doing 50 you now have the assurance and peace of mind that comes with purchasing a product made by one of the leading manufacturers. All products. brought to you are manufactured to the highest standard of performance and safety and.as part of our philosophy of customer service and satisfaction, are backed by our comprehensive 1 Year Warranty. We hope you will enjoy using your purchase for many years to come.

Safety Warning: Keep in mind that using FreedConn can fimit the audibilty of ‘ambient sounds. Listening to music at maximum volume in addition to temporariy adapting to make it impossible to hear soft sounds can lead to permanent hearing damage.
Warm Tips: In order to get the best sound quality experience, please make sure Speakers are within 2mm of ears.

Before the first use, please charge the device.

When using a TF card for the first time, please use the recorder for formatting.

Product Features Introduction

Build-in Camera
1080P 120° wide angle lens, allowing you to take videos/photos anywhere and anytime.

Bluetooth 5.0 version
Bluetooth wireless transmission with higher efficiency and more stable wireless intercom.

Intercom connection with Bluetooth headset from other brands
Support connection with most Bluetooth headset from other brands.

Type C connector
Greatly reduce the charging time to avoid delay of your cycling plans.

Connection to walkie-talkie
Connect to handheld walkie-talkie through PPT K wire.

Use while charge
The product can also be used while charging, without delaying your cycling plans.

High capacity battery
1500mAh high performance lithium polymer battery

Connection to two mobile phones
It can connect to 2 mobile phones at the same time, without missing any call.

IP65 Water-proof Grade
Protect the product effectively so it can be normally used even on rainy days

RI Plus Wireless Intercom Function
Bluetooth intercom between the rider and the backseat passenger or among riders, The farthest group intercom distance is 1000 meters (note: Under optimal use conditions; Actual intercom scope varies according to the actual service conditions)

Music sharing function
Music sharing between the rider and the backseat passenger or among riders.

WIFI Technology
Videos and pictures taken can be transmitted to mobile phones at high speed.

Radio function
Built-in FM radio

Voice prompt
Personalized voice prompts keep you updated with current operations

Voice calls
Voice commands allow the mobile phone’s voice assistant to perform tasks such as making calls

Detailed description of the connector/ buttons

1. Bluetooth switch button/ multi-function button
2. knob button
3. Recorder on/off button, video button/photo-taking button
4. WiFi button/Intercom button
5. Camera lens
6. Video indicator light
7. Bluetooth indicator
8. TF card slot
9. Headphone jack
10. The reset button
11. Charging port /USB port

Detailed description of the basic functions and operation

1. Bluetooth power on: Press the multi-function button for about 3 seconds, release it when you hear the prompt “Welcome to use Freed conn products”.
2. Bluetooth power off: Press the multi-function button for 3 seconds, release it when you hear the prompt “power off “.
3. Switching between English and Chinese: In standby or music pause mode, tap the multi-function button and the intercom button at the same time.
4. Turn on/ turn off automatic call answering: In standby state or music pause state, turn the knob counterclockwise and tap the intercom button.
5. Volume adjustment: In any modes, turn the knob clockwise without releasing to increase the volume in the current mode, and when it reaches the maximum, there will be a “beep” prompt sound; turn the knob counterclockwise without releasing to reduce the volume in the current mode, and when it reaches the minimum, there will be a “beep” prompt sound.
6. Delete the pairing records: Press on the power-off button till you see the red light on (after hearing the power off prompt), hold for another 5 seconds till you see the red light flash twice (with beep prompt), then the records are successfully deleted and the device is turned off.. (Pressing for 3 seconds to turn off normally will not delete the addresses.)

Bluetooth connection with mobile phone, GPS, etc

1. Ensure that the host machine is off and place the device within a visible scope of one meter.
2. Press on the multi-function button for 8 seconds in the power-off state, and the host will automatically enter the pairing state. At this time, the blue light and red light will be flashing alternately.
3. Turn on the Bluetooth device to be paired, search and select “R1 Plus” for pairing, and you will hear the voice prompt “Bluetooth connected”. When the indicator turns on and the blue light blinks regularly, the pairing is successful.
4. Music Playing/pause: After connecting with the mobile phone, first turn on the music player on the mobile phone, then click the play button or press the multi-function button to play the music, and press the multi-function button again to pause the music.
5. Switching between the previous and the next songs: When playing music, turn the multi-function button clockwise to switch to the next song, and turn it counterclockwise to switch to the previous song.
6. Answering phone calls: After the Bluetooth intercom headset is paired with the mobile phone, press the multi-function button once to answer an incoming call. If no operation is performed, the call will be automatically answered after 15 seconds. (If you do not need automatic answering, you can turn the knob counterclockwise and tap the intercom button in the standby or music pause state to turn off automatic answering of calls.)
7. Rejection of incoming calls: Press on the multi-function button for 2 seconds and release it to reject an incoming call.
8. Voice Switching: When you answer a call with Bluetooth headset, press on the multi-function button for two seconds to switch the voice to the mobile phone, and press the multi-function button for another two seconds to switch the voice back to the headset.
9. Ending a Call: Press the multi-function key once to end a call.
10. Voice Call: After connecting to the mobile phone, press on the multi-function button and turn the knob clockwise to activate the voice call function, or manually activate the voice assistant via the mobile phone.
11. Music /FM Switchover: In music mode, press the multi-function button twice to switch to FM mode, and press the multi-function button twice to switch back to music mode.
12. FM frequency modulation: Turn the knob clockwise to switch to the next frequency band, and turn the knob counterclockwise to switch to the last frequency band.

Steps for Bluetooth intercom connection between two R1 Plus devices

1. Ensure that both devices are power-off and placed within a visual range of 1 meter.
2. Press on the power buttons of the two devices at the same time for 8 seconds. When you hear the prompt “Pairing”, the red and blue indicators blink alternately, and the two devices are in the ready-to-pair state.
3. Press the intercom button of one of the two devices to start pairing, it will automatically search for the other device, and you will hear “Intercom is connected”. When the blue light blinks regularly, it means that the pairing has been completed and you can start the intercom.

Note: if the pairing is not successful, please delete the pairing record first, and then repeat the above operations. (If there is a phone call coming during an intercom call, the device will automatically disconnect the intercom, and automatically resume the intercom once the call finishes. If one of your companions invites you to join an intercom during a phone call, you will fail to accept the intercom, but there will be a “beeping” prompt).

Music sharing between two users

1. Ensure that the two devices only keep the pairing information of each other. (You can delete the pairing of the two devices and then re-pair them according to step 4.10)
2. Pairing with mobile phones according to step 4.0
3. After completing the steps above, when device A need to share music with device B, if they are both playing music, device B must pause the music and then double-click the intercom button of either device A or device B to listen to the music shared by device A. During the music sharing process, press the multi-function button of device A to stop music playing and press the multi-function button of device B to exit the music sharing, or double click the intercom button of either device A or device B to exit music sharing. (If music sharing fails, please follow 3.0.6 to delete the pairing records and then re-pair the recorder and mobile phone following the steps in 4.10 and 4.0).

Multiple-users intercom connection and using methods

Note: the first and the last devices (A and F in the below pictures) should never be paired.

Steps of Intercommunicate connection amang six R1 Pius devices.

Note: th frst and the ast devices (A.and In the below pctures) should never.

Intercom connection with other headsets

In the power-on state, turn the multi-function button clockwise and tap the intercom button, when the red and blue light flashes, it is in the state of third-party pairing. After the third party headset enters the pairing state and connects to the mobile phone according to the instructions, tap the intercom button of our headset to connect the third party headset to the intercom state. (Note: The connection with the phone will be disconnected after connecting the third-party headset).

Detailed description of video recording functions

1. Turn on the recorder and start the video recording: First, insert the SD card with the texted side on top into the card slot facing the front of the machine (it supports a maximum of 64G memory card), then long press the recording switch button for 3 seconds to start the machine; After turning on the machine, press the video recording button to start recording. You can also enter video recording by clicking on the camera icon in the the APP in the state of WIFI connection. When the video is on you will hear the prompt”video on”, and a green light will stay on. If there is no memory card is inserted, you will hear the prompt “please insert a memory card”. If the video fails to play after the SD card is inserted, please format the SD card in the APP (see 6.0 APP operation details).
2. Pause recording: n the recording state, press the video switch to stop recording, or click the red button in the APP to stop recording. At the same time, you will hear the prompt “recording pauses”. The green LED indicator will turn to the flashing state. (When the memory card runs out of capacity, the newly recorded video will automatically replace the first video stored on the memory card. If some SD cards are full and cannot start recycled video, you can delete 3-5 videos, then the videos can be automatically recycled.
3. Photo taking function: In the recording state, double-click the recording switch to capture a photo.
4. Starting the WiFi function: When the recorder is on, press on the WiFi button for 2-3 seconds to turn on the WiFi, you will hear the prompt of “WiFi on”, and the green light will blink every 0.5s.
5. Turn off the WiFi function: When the WiFi is on, press on the WiFi button for 2 to 3 seconds to turn it off. You will hear the prompt of “WiFi off”, and the green light will blink every 2S

Detailed Description of Application functions and buttons

Download the “roadcam” APP: Scan the QR code below to download the “roadcam” APP to your mobile phone (The APP is compatible with most mobile phones. If you cannot use it normally after downloading the APP, please watch and process the recorded videos on your computer according to the methods introduced in 6.0.5).

Connect the recorder’s WIFI: Turn on the recorder and WIFI according to the methods in 5.0.1 and 5.0.4, then open the WIFI list in the phone, select “Freedconn” and input the initial password “12345678” to connect. If the phone indicates that “the current WLAN is unavailable, continue to use this WLAN or not” during the connection, please select “YES”. (If it indicates “Network access is denied” when you connect to the WIFI again, please turn off the recorder WIFI and restart, refresh the WIFI list on your phone and reconnect.)

Start the “roadcam” APP: click on the “roadcam” APP in the mobile phone to enter and you will get to the interface as below figure 1:

Video recording and photo taking: Click the camera icon in the middle of figure 1 to enter the interface in figure 2. You can record a video by clicking the recorder icon. Click the camera icon to switch to the photo taking mode and click again to take photos.

Check the videos and pictures: Click the album icon in figure 2 to preview the videos and pictures. Click the previewed images to play or to download. (Note: The playing mode is actually for preview only, the videos and pictures are vague and and soundless. If you want to review HD ones, please download the video and image to view or delete them in the “photo album”.) Another way is connect your computer and recorder by a USB data cable and view in your computer. You can also pull out the memory card and connect your computer with a card reader, and find the U disk in the computer and then enjoy the HD videos and pictures. (Note: The disc can only be read when the recorder is power-on.).

APP function setting: Click the setting icon in the upper right corner in figure 2 to enter the setting interface in figure 3,4 and 5 below.

Video resolution: Click to adjust the resolution of videos. It supports the maximum resolution 1080 Full High Definition 1920X1080 (note: the higher the resolution is, the more memory will be occupied.)

Exposure compensation: Click to adjust the exposure rate of videos.

Movement detection: Click and start or shut down this function. After starting the function, the recorder will automatically start recording when it detects movement and will stop recording when movement stops. If you don’t want the recorder to work automatically, please shut down the function “movement detection”.

Cyclic recording time: Click to select the recording time of a single video, including “Off”, “1 minute”, “2 minutes”, “3 minutes”, “5 minutes” and “10 minutes”. The default cyclic recording time is 5 minutes if you select “Off”.

WDR: Click to turn WDR on or off. WDR is short for Wide Dynamic Range. Wide dynamic makes you see both the brightest and darkest part of the scene clearly at the same time. It is recommended to turn it on when recording a scene with a large difference in light.

Recording audio: Click to turn on or off the recording audio. If the recording environment is too noisy, you can turn off the the recording audio.

Photo resolution ratio: Click to select the definition of a photo, the maximum definition of a photo is 12m (4032X3024).

Photo quality: Click to select the photo quality, that is, fidelity of the photo.

Continuous shooting : When you start this function in the photo taking mode, the recorder will take a photo continuously every 3 seconds. When this function is shut down, only one photo is taken for each click.

Sharpness: Click to adjust the sharpness of the photo. When the sharpness is increased, the details on the surface of the photo will have a higher contrast and the photo will look clearer.

ISO: Click this item to adjust the sensitivity of the recorder, normally choose “automatic”.

Steady shot: Once the steady shot function is enabled, it can reduce the impact of hand shocking while taking photos. It is recommended to enable it.

White balance: The effect of white balance can be adjusted according to the weather conditions, and it can also be set to be automatic.

Light source frequency: You can adjust the light source according to your preference.

Button sound: The prompt sound of the recorder can be turned on or off.

Camera time watermarking: When this function is enabled, the time watermarking will be added to the lower left corner of each video and photo. (The time will be the same as the one in your phone. If the recorder time is incorrect, it can be updated by connecting with the APP.)

Date/Time: The display format of the date and time is adjustable.

Clearing Cache: Clear the APP runtime cache

Formatting   device: Click this button to format TF memory card. (When the memory card fails to record or when a new card is inserted, it is suggested to format the card after it is connected to the APP.)

Factory data reset: Click this button to restore the factory settings of the APP.

WIFI account: Click this button to change the WIFI name, and the change will take effect after the recorder is restarted.

WIFI password: This item can change the WIFI password, and the change will take effect after the recorder is restarted. (Note: The WIFI password must be 8 digits, if the new password is less than 8 digits or if you forget the new password, you will fail to connect the WIFI and need to reboot the device according to the guideline on www.fdcdc.com. So do not change the password unless necessary.).

Steps of R1 Plus Connects to Intercom

1. As shown in the figure below, connect the intercom with PTT control line when R1 plus is on;
   

2. Bind the PTT Velcro belt to the handlebars of the motorcycle;

3. Paste the PTT button of the PTT control line on the VELCRO belt

4. Put the inter phone in a proper position and you can use the intercom function by pressing the PTT button during cycling.

Note:  The priority of these functions is “Phone call> PTT intercom> Music> GPS> voice prompt”.

Product installation and removal, packing list

Installation procedures

Insert e memory card (Maximum 64 TF card s supported)

Inset the clpito the helmel (100 much force may lead to breakage of the clam)

Install the device to the clip

Inset the headphone plug nta the R1 plus fack, and the instalaion is completec

Removal procedures

Packing list

1. Bluetooth host *1

2. Microphone & loud speaker *1

3. Clip*2

4. Screwdriver*1

5. Headphone Velcro tape *4

6. Data cable *1

7. Mini microphone Velcro*2

8. Product manual*1

Product specifications and parameters

Frequency: 2.4 GHz
Weight: 77g
Size: 98X 58X 30mm
Power adapter: DC 5V/1A
Lens: 1080P
Call duration: 30 hours
Video time: 4.5 hours
Charging time: about 2.5 hours
Standby time: Automatically turn off in 15 minutes if no connection nor operation.
Music time: 48 hours.

Battery capacity: 1500mAh (When the battery is too low to keep the device on, there will be a reminder “Low power, please charge”. After the recorder is off due to low battery, you can still listen to music for 40 minutes via Bluetooth, which will report low battery reminder every 15 minutes and will be off automatically when the battery is too low. During charging, the red light remains steady on and goes off when battery is full.).

Common Trouble Shooting

Bluetooth does not start
When the recorder can be turned on while Bluetooth can’t, it is usually because the Bluetooth does not successfully reset when it is turned off. You only need to press the reset button about 1 second or you can plug the charger to reset. (Charging in the power-on state will not reset.)

Recorder does not start
With sufficient power, but the recorder can’t be started, it is usually because the recorder does not successfully reset when it is shut down. You only need to press the reset button for 1 second or you can plug the charger to reset. (The recorder will not reset by charging when it is on). 10.0.3 Time lag occurs while viewing videos or listening to music in the APP.

When you open the APP to review the video, the video code stream is too large, so it will interfere with the Bluetooth. You need to turn off the Bluetooth temporarily and can only turn on after exiting the APP.

There is “crackling” noise when plays video in the mobile phone To play first videos downloaded from mobile apps, please turn off 4G and WIFI, then the noise will disappear.

Connected to Freedconn’s WIFI, but the mobile phone shows no WIFI network. It is normal that WIFI itself can’t access the internet, and it doesn’t affect the use. The function can be used when the WIFI connection is normal between the recorder and the mobile phone.

The mobile phone can’t find the recorder’s WIFI while it is available. The mobile phone can search the WIFI but can’t be connected.

The WIFI software version may not be compatible with the mobile phone. You can upgrade the WIFI software of R1 PLUS by contacting the manufacturer via email: [email protected].

When turning on the recorder, the prompt indicates that it fails to start recording and need to format the memory card, but still not workable after formatting the memory card with PC.

Please download roadCam APP, start the WIFI of the mobile phone and that of the recorder ,and connect the recorder’s WIFI in the APP and rename it as Freedconn. Upon connection, find the setting options and choose the formatting function at the bottom and click to format.

TF card selection Suggest to select a 64GB genuine memory card of class 10 or higher. High-quality TF cards have longer service life than the low-quality ones. When the video screen becomes blurred and the frame rate decreases, please replace the card.
The higher the TF card’s quality is, the longer time it can be used, and vice verses.

After-sales service

Forany other problems nol lsted above, you can scan the below QR code onter the offcial website 0 find Technical support page or solutions.

At sals to chnical support.

Warranty Card

Model Number: R1PLUS

Please keep your shopping receipt, warranty card and the seal label.

After-sales service: [email protected]

Failure Description:

Please affix a copy of invoice on the back of warranty card as a proof of purchase date. If you find any problems during use of our product, please contact our after-sales service. Please make sure that you describe the problems clearly on warranty card so that we can handle them timely.

Symbols

Documents / Resources

| FreedConn BL06.0050.0633 Motorcycle Bluetooth Headset with Camera [pdf] User Manual
BL06.0050.0633 Motorcycle Bluetooth Headset with Camera, BL06.0050.0633, Motorcycle Bluetooth Headset with Camera, Bluetooth Headset with Camera, Headset with Camera, Camera
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>