EPSON WH-55 Remote Controller Instruction Manual
- June 5, 2024
- Epson
Table of Contents
WH-55 Remote Controller
Instruction Manual
WH-55 Remote Controller
N0.
| Button|
Features
---|---|---
1| | POWER| Perform sleep/wake on the box
2| | Mute| Turn off the sound
3| | UP| Move focus/volume up +
4| | DOWN| Move focus/volume down
5| | LEFT| Move focus to / left / rewind / switch to previous channel
6| | RIGHT| Move focus / fast forward / switch to the next channel
7| | ENTER| Enter the currently selected focus page/pause play/execute button
prompt command
8| | BACK| Return to the previous or previous page
9| | home| home
10| | VOICE| (It works only after Bluetooth pairing is connected)
11| | VOL+| Increase the volume (global applies, this button has only one
operation)
12| | VOL-| Decrease the volume (global applies, this button has only one
operation)
13| | apps|
14| | menu|
15| | youtube|
16| | input| input
17| | keystone|
18| | backward| Show rewind
19| | play| Program play pause
20| | forward| Fast forward to the show
---|---|---|---
1. Remote control key value
System code 0x8355
Code format NEC 6121F
Key code value:
Note: IR always sends infrared, BT sends Bluetooth in Bluetooth state, IR&BT works simultaneously in Bluetooth state under Bluetooth
**Infrared control
**
Format
NEC format
Remote control instructions
1. Special requirements for remote control
-
When Bluetooth is connected, the remote control sends the Bluetooth key value; if Bluetooth is not connected, the infrared key value is sent.
-
Indicator light: red, each time the button is pressed, the indicator light flashes Low voltage reminder: When the battery is low, the indicator light flashes quickly. As long as it is still in operation, it will remain in the flashing state. When it is no longer operated by the remote controller, it will flash 5 times or flash 3 seconds, then stop and go out.
-
Support Bluetooth remote control online upgrade, and trigger upgrade through HOST.
a. “Enter”+”home”
b. “Enter”+”home”
c. “Enter”+”home” -
Pairing method:
a. Simultaneously press “Enter” + “home” on the remote control for three seconds to send the code information;
b. If the pairing is not successful, if you still press the “Enter” + “home” button, the pairing broadcast will be sent all the time so that the user can pair.
c. Press the “Enter” + “home” button once to match successfully. Do not clear the pairing and then pair again. After a key pairing is successful, the pairing broadcast can no longer be sent until the next time the button is pressed. 12ms Connection interval12ms 510m -
Remote control distance: 10m
-
Bluetooth device name:
-
When the button has 2 or more buttons (except the pairing button), the remote control stops working when pressed and resumes when the button is released.
-
When the button is pressed for more than 30S, the remote control automatically stops working and then resumes work after release.
-
After “Back”+”Right” is pressed for 500ms, the infrared key value “B9H” is sent until it is pressed. If any button is released or it is completely released, “B9H” will be stopped.
-
bug 10)Support “Enter” + “back” to upload bug report function
-
“back” + “down” to open the Accessory page 2.
- Pairing function requirements: there must be no problems that the Bluetooth
device cannot be scanned or paired (including continuous pressing of the
pairing key within a short period of time), please verify 50 times to ensure
that there is no problem;
2)Reconnection function requirements: there must be no problems with the connection failure, including the box power failure and the connection, the remote control power failure and the connection, standing for 2 hours to reconnect, etc., please verify 50 times to ensure that there is no problem; - Anti-interference function requirements: there must be no problems that
greatly affect the host’s WIFI throughput, please ensure that the host’s WIFI
throughput is normal when connecting the remote control;
4). Performance requirements: It is required to support 10m, and there must be no voice call jams, loss, and remote control button jams, missing codes, or continuous keys;
5). Power consumption requirements: the remote control can be used continuously for at least 6 months
6)Voice: 16Khz voice sample with 16-bit sampling, short press the voice button (color button) to start recording, and the remote control will stop recording after receiving the stop recording command from the voice engine. The voice timeout is protected for the 30s, and the recording is forced to exit.
7). The box software can control the opening and closing of the MIC.
8). Support the remote control MIC and other MIC (such as the recording key on the phone apk) to alternate and switch voice input.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
IC Warning
This device complies with Industry Canada’s license-exempt RSS. Operation is
subject to the following two conditions: (1) This device may not cause
interference; and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>