KOHLER 195711117557 18 Inch Pendant Light Installation Guide
- June 16, 2024
- Kohler
Table of Contents
KOHLER 195711117557 18 Inch Pendant Light
Product Information
Specifications
- Product: Pendant Light
- Model Number: 1554281-2-A
- Manufacturer: Kohler Co.
- Indoor use only
- Maximum bulb rating: 100 W
FAQs
- Q: Can I use bulbs with a wattage higher than 100 W?
- A: No, exceeding the maximum bulb rating of 100 W may pose a risk of fire. Please do not use bulbs with a wattage higher than the specified limit.
- Q: Can I install this fixture outdoors?
- A: No, this fixture is designed for indoor use only. Installing it outdoors may cause damage and void the warranty.
- Q: Do I need to hire a qualified electrician to install this fixture?
- A: It is recommended to have a qualified electrician install the fixture to ensure proper installation and safety.
Product Installation Instructions
Before You Begin
DANGER: Risk of electric shock. To avoid electrical shock, the electricity must be turned OFF at the circuit breaker or fuse box before beginning installation. DANGER: Risk of electric shock. To avoid electrical shock, the electrical outlet box must be properly grounded.
CAUTION: Risk of property damage. To avoid risk of fire, this fixture has been rated for bulbs up to 100 W. Do not exceed this rating.
Follow all local plumbing, building, and electrical codes.
Please read all instructions before you begin. The fixture should be installed
by a qualified electrician. Carefully inspect the fixture for damage.
Install the Mounting Plate
Carefully pull out the wiring from the electrical outlet box and allow the wires to hang down. Place the flat side of the mounting plate flat against the electrical outlet box. Align the slotted mounting holes on the mounting plate with the holes on the electrical outlet box. Securely tighten the mounting plate to the electrical outlet box with the mounting screws.
Assemble the Downrods and Canopy
Determine the height that you want the fixture to be located. Select a combination of different length downrods that will place the fixture at the desired height. Insert the electrical wires and ground wire through each of the downrods and then thread the downrods together. Thread one end of the downrods to the stem of the socket assembly. Insert the electrical wires through the coupling hook, coupling ring, and canopy.
Connect the Electrical Wires
Insert the wires from the socket through the center of the mounting plate. Attach the coupling hook onto the coupling that is preinstalled onto the mounting plate. Close the coupling hook. Make a loop in the ground wire and wrap around the grounding screw on the mounting plate. Tighten the grounding screw. Fasten the ground wires together with the provided wire nut and wrap the wire nut with electrical tape. Attach the neutral wire (with the grooves), from the fixture, to the neutral wire (usually white) in the electrical outlet box. Attach the hot wire (with the writing), from the fixture, to the hot wire (usually black) in the electrical outlet box.
Secure the Fixture
Verify that all plastic wire nuts are securely fastened and strands of bare wire are not exposed. Carefully position the wires inside the electrical outlet box behind the mounting plate. Position the canopy over the coupling. With the canopy flush against the ceiling, verify that there are threads showing. Secure the canopy to the coupling with the coupling ring.
Install the Shade
- Place the rubber washer on top of the socket. Slide the shade over the socket, ensuring it is aligned properly.
- Place a plastic washer on top of the shade, followed by a socket nut. Tighten the socket nut to secure the shade in place.
Information
Thank You for Choosing KOHLER
Need help? Contact our Customer Care Center.
- USA/Canada: 1-800-4KOHLER (1-800-456-4537) Mexico: 001-800-456-4537
- Service parts: kohler.com/serviceparts
- Care and cleaning: kohler.com/clean
- Patents: kohlercompany.com/patents
Warranty
- This product is covered under the KOHLER® Indoor Lighting Fixtures Limited Warranty, found at kohler.com/warranty.
- For a hardcopy of warranty terms, contact the Customer Care Center.
Tools and Materials
Plus
- E26 Base ST/A/G bulb(s) (Max 100 W)
Before You Begin
DANGER: Risk of electric shock. To avoid electrical shock, the
electricity must be turned OFF at the circuit breaker or fuse box before
beginning installation.
DANGER: Risk of electric shock. To avoid electrical shock, the electrical
outlet box must be properly grounded.
CAUTION: Risk of property damage. To avoid risk of fire, this fixture has
been rated for bulbs up to 100 W. Do not exceed this rating.
- Follow all local plumbing, building, and electrical codes.
- Please read all instructions before you begin.
- The fixture should be installed by a qualified electrician.
- This fixture is for indoor use only.
- Carefully inspect the fixture for damage.
Installation Instructions And Connections
Install the Mounting Plate
- Carefully pull out the wiring from the electrical outlet box and allow the wires to hang down.
- Place the flat side of the mounting plate flat against the electrical outlet box.
- Align the slotted mounting holes on the mounting plate with the holes on the electrical outlet box.
- Securely tighten the mounting plate to the electrical outlet box with the mounting screws.
Assemble the Downrods and Canopy
- Determine the height that you want the fixture to be located. Select a combination of different length downrods that will place the fixture at the desired height.
- Insert the electrical wires and ground wire through each of the downrods and then thread the downrods together.
- Thread one end of the downrods to the stem of the socket assembly.
- Insert the electrical wires through the coupling hook, coupling ring, and canopy.
Connect the Electrical Wires
- Insert the wires from the socket through the center of the mounting plate.
- Attach the coupling hook onto the coupling that is preinstalled onto the mounting plate. Close the coupling hook.
- Make a loop in the ground wire and wrap around the grounding screw on the mounting plate. Tighten the grounding screw.
- Fasten the ground wires together with the provided wire nut and wrap the wire nut with electrical tape.
- Attach the neutral wire (with the grooves), from the fixture, to the neutral wire (usually white) in the electrical outlet box.
- Attach the hot wire (with the writing), from the fixture, to the hot wire (usually black) in the electrical outlet box.
Secure the Fixture
- Verify that all plastic wire nuts are securely fastened and strands of bare wire are not exposed.
- Carefully position the wires inside the electrical outlet box behind the mounting plate.
- Position the canopy over the coupling. With the canopy flush against the ceiling, verify that there are threads showing.
- Secure the canopy to the coupling with the coupling ring.
Install the Shade
- Position the shade onto the socket base.
- Set the plastic washer on the socket nut and then lift the socket nut inside the shade to thread onto the socket base.
- Handtighten the socket nut to secure the shade(s).
- Align the holes of the shade with the two fixture arms.
- Secure the shade to the fixture arms with a rubber washer and shade screw.
- Insert the bulb into the fixture.
- Turn ON the main electrical supply from the main fuse or the circuit breaker.
- Confirm proper operation.
Contact
- USA/Canada: 1-800-4KOHLER (1-800-456-4537)
- Mexico: 001-800-456-4537
- kohler.com
©2023 Kohler Co.
References
- Toilets, Showers, Sinks, Faucets and More for Bathroom & Kitchen | KOHLER
- How to Use KOHLER Cleaning Products | KOHLER
- Toilets, Showers, Sinks, Faucets and More for Bathroom & Kitchen | KOHLER
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>