deta 1016WH Compact HEPA Automatic Hand Dryer Instruction Manual

deta 1016WH Compact HEPA Automatic Hand Dryer

Product Information

Specifications

• Voltage rating: 230V – 50Hz
• Total load rating: 1100W
• Rated Heater Element Power: 350W
• Motor Power: 650W
• Air Speed: 90m/s
• Noise Level: 65dB
• IP Rating: IPX1
• Effective Airflow: 170m3/h
• Dimensions: 265x250x180mm
• Guarantee: 1 Year

Product Usage Instructions

Installation Instructions

1. Remove the front cover by removing the securing screws at the base of the hand dryer, and releasing the retaining clips at the top of the hand dryer.
2. Release the plug of the sensor lead at the circuit board, see Fig 1.
3. Using the base as a template, mark out the fixing holes on the mounting surface. See Fig 2.
4. Feed the supply cable through the hole in the base and terminate the conductors into the terminal block ensuring the correct polarity is observed.
5. Secure the supply cable in the cord grips provided.
6. Secure the base to the mounting surface using the wall plugs and screws supplied.
7. Reconnect the sensor lead to the circuit board.
8. Offers the cover back to the base and secure it in position.

Cleaning the Filter

1. Ensure the power supply is switched off.
2. Remove the filter housing from the base. See Fig 3.
3. Take out the filter and shake out any dust or particles in the filter.
4. Return the filter to the housing and return the housing to the hand dryer.
5. Note: Do not wash the filter with water.

Operation
The hand dryer is automatically activated when hands are placed under the air outlet. Once the hands are removed, the hand dryer automatically switches off within 2 seconds. If the hand dryer is running continuously, it will switch off after 60 seconds to conserve energy. To reactivate the hand dryer, move the hands away from the air outlet and place back.

FAQ

• Q: How often should I replace the HEPA filter?
• A: It is recommended that the HEPA filter is replaced every 6 months.
• Q: What should I do if the hand dryer does not automatically switch off?
• A: If the hand dryer does not automatically switch off within 2 seconds of removing your hands, try moving your hands away from the air outlet and placing them back to reactivate the hand dryer. If the issue persists, please contact our technical helpline at +44(0)1582 544 548 for further assistance.

Compact HEPA Automatic Hand Dryer

Features

• Low energy, automatic hand dryer suitable for commercial applications such as offices, restaurants, and schools
• Includes a standby / Power-On LED indicator and changeable heat settings to suit the environment
• 10 to 15 seconds drying time with automatic shut-off when not in use
• Durable polycarbonate housing
• Self-resetting overheated thermostat provides protection from overheating if the hand dryer becomes blocked

Safety Instructions

1. These instructions should be read carefully and retained after installation for future reference and maintenance.
2. Ensure that the mains power is switched off before carrying out installation or maintenance.
3. Installation must be carried out by the current edition of IET wiring regulations BS 7671, and by a qualified electrician.
4. The hand dryer should be supplied from a switched fused spur. This Hand Dryer is electrical class 1 construction and must be earthed.
5. Ensure all electrical connections are secure and that there are no loose strands.
6. Do not install above washbasins or immediately adjacent to urinals, lavatories, baths, and showers.
7. When in use, the hand dryers will accumulate dust. Cleaning and maintenance must be carried out regularly.
8. The unit is intended for drying hands only. Long hair should be kept away from air inlet vents.

Environmental Instructions
This product may contain substances that can be hazardous to the environment if not disposed of properly. Electrical and electronic equipment should never be disposed of with general waste but must be separated for its correct treatment and recovery. Where possible recycle your packaging.

Installation Instructions

1. Remove the front cover by removing the securing screws at the base of the hand dryer, and releasing the retaining clips at the top of the hand dryer
2. Release the plug of the sensor lead at the circuit board, see Fig 1
3. Using the base as a template, mark out the fixing holes on the mounting surface. See Fig 2
4. Feed the supply cable through the hole in the base and terminate the conductors into the terminal block ensuring the correct polarity is observed
5. Secure the supply cable in the cord grips provided
6. Secure the base to the mounting surface using the wall plugs and screws supplied
7. Reconnect the sensor lead to the circuit board
8. Offers the cover back to the base and secure in position

Cleaning the Filter

1. Ensure the power supply is switched oof
2. Remove the filter housing from the base. See Fig 3
3. Take out the filter and shake out any dust or particles in the filter
4. Return the filter to the housing an return the housing to the hand dryer
5. Note : Do not wash the filter with water.

Operation

The hand dryer is automatically activated when hands are placed under the air outlet. Once the hands are removed, the hand dryer automatically switches off within 2 seconds. If the hand dryer is running continuously, it will switch off after 60 seconds to conserve energy. To reactivate the hand dryer, move the hands away from the air outlet and place back.

Specification

Rated

Power

| Heater Element| 350W| IP Rating| IPX1
Motor| 650W| Effective Airflow| 170m3/h
Guarantee| 1 Year| Dimensions| 265x250x180mm

• It is recommended that the HEPA filter is replaced every 6 months

Deta Electrical Company Ltd
UK : Panattoni Park Luton Road Chalton Bedfordshire LU4 9TT
EU : Unit 16 Ashbourne Industrial Estate, Ashbourne Co. Meath, A84 W972, Ireland deta.co.uk
Technical Helpline : +44(0)1582 544 548

INS0012 V2.0 08/23 NPD0685 T11

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>