deta 1011WH Automatic Hand Dryer Instructions

Table of Contents

deta-1011WH-Automatic-Hand-Dryer-PRODUCT

Specifications

Installation Instructions

Remove the metal front cover by unscrewing the security screws on the sides of the hand dryer.
Fix the base of the hand dryer on the mounting surface using the wall plugs and provided screws.
Feed the supply cable through the cable entry hole in the base and connect the conductors to the terminal block with the correct polarity.
Secure the supply cable in the cord grips and connect it to a spur.
Reattach the metal front cover and secure it in position with the security screws.

HEPA Filter Replacement

Using the hand dryer base as a template, mark and drill the fixing holes on the mounting surface.
Push the filter cover to open it and remove the old filter.
Insert the new filter and close the filter cover securely.

Operation:

The hand dryer is activated automatically when hands are placed under the air outlet. It switches off within 2 seconds after hands are removed.
If running continuously, it will turn off after 60 seconds to conserve energy.
To reactivate, move your hands away from the air outlet and place them back.

FAQ:

Q: How often should the HEPA filter be replaced?

A: It is recommended to replace the HEPA filter every 6 months for optimal performance.

Manufactured from 1.2mm grade 304 stainless steel to protect against corrosion and vandalism with a low noise level of 72dB
Anti-tamper cover (fixing screws included)
Internal switch to alternate between warm air at 950W or room temperature air at 500W, saving energy during warmer periods
Self-resetting overheated thermostat protects from overheating if the hand dryer becomes blocked
Automatic shut off after 60 seconds to avoid wasted energy
Self-resetting overheated thermostat protects from overheating if the hand dryer becomes blocked

These instructions should be read carefully and retained after installation for future reference and maintenance.
Ensure that the mains power is switched off before carrying out installation or maintenance.
Installation must be carried out under the current edition of IET wiring regulations BS 7671, and by a qualified electrician.
The hand dryer should be supplied from a switched fused spur. This Hand Dryer is electrical class 1 construction and must be earthed.
Ensure all electrical connections are secure and that there are no loose strands.
Do not install above washbasins or immediately adjacent to urinals, lavatories, baths, and showers.
When in use, the hand dryers will accumulate dust. Cleaning and maintenance must be carried out regularly.
The unit is intended for drying hands only. Long hair should be kept away from air inlet vents.

Environmental Instructions

This product may contain substances that can be hazardous to the environment if not disposed of properly.
Electrical and electronic equipment should never be disposed of with general waste but must be separated for its correct treatment and recovery.
Where possible recycle your packaging.

Remove the metal front cover by removing the security screws on the sides of the hand dryer.
Using the hand dryer base as a template, mark out and drill the fixing holes on the mounting surface.
Fix the base of the hand dryer on the mounting surface using the wall plugs and the screws provided.
Feed the supply cable through the cable entry hole in the base and terminate the conductors into the terminal block ensuring the correct polarity is observed.
Secure the supply cable in the cord grips and terminate into a spur.
Replace the metal front cover on the base and secure in position using the security screws.

The hand dryer is automatically activated when hands are placed under the air outlet. Once the hands are removed, the hand dryer automatically switches off within 2 seconds.
If the hand dryer is running continuously, it will switch off after 60 seconds to conserve energy. To reactivate the hand dryer, move the hands away from the air outlet and place them back.

Input Voltage:	220V – 240V AC 50Hz	Air Speed	100m/s
Electrical Classification:	Class I	Noise Level (at 2m)	72dB

Rated

Power

It is recommended that the HEPA filter be replaced every 6 months
Deta Electrical Company Ltd
UK: Panattoni Park Luton Road Chalton Bedfordshire LU4 9TT
EU: Unit 16 Ashbourne Industrial Estate, Ashbourne Co. Meath, A84 W972, Irelanddeta.co.uk
Technical Helpline: +44(0)1582 544 548