deta 1019WH 1.8kW Heavy Duty Hand Dryer Instruction Manual
- June 17, 2024
- deta
Table of Contents
deta 1019WH 1.8kW Heavy Duty Hand Dryer
Specifications
- Voltage rating: 230V – 50Hz
- Total load rating: 1800W
- Rated Heater Element: 1200W
- Motor Power: 600W
- Guarantee: 1 Year
- HEPA Filter Replacement: Recommended every 6 months
- Air Speed: 90m/s
- Noise Level: 72dB
- IP Rating: IPX1
- Effective Airflow: 180m3/h
- Dimensions: 320x280x170mm
Product Usage Instructions
Installation Instructions
- Remove the front cover by taking out the securing screws at the base of the hand dryer.
- Use the base as a template to mark out the fixing holes on the mounting surface.
- Feed the supply cable through the hole in the base and connect the conductors into the terminal block, ensuring correct polarity.
- Secure the supply cable in the cord grips provided.
- Mount the base to the surface using the wall plugs and screws provided.
- Attach the cover back to the base and secure it with the screws.
Operation
The hand dryer activates automatically when hands are placed under the air
outlet. It turns off within 2 seconds after hands are removed. If it runs
continuously, it will switch off after 60 seconds to save energy. To
reactivate, move hands away from the outlet and place them back.
Frequently Asked Questions (FAQ)
-
Q: How often should I replace the HEPA filter?
A: It is recommended to replace the HEPA filter every 6 months for optimal performance. -
Q: What should I do if the hand dryer does not automatically switch off?
A: If the hand dryer does not switch off automatically, ensure that there are no obstructions blocking the sensor area. Clean the sensor area if needed.
Compact HEPA Automatic Hand Dryer
Features
- Heavy duty, automatic hand dryer suitable for commercial applications such as offices, restaurants and schools
- Includes a standby / Power-On LED indicator and changeable heat settings to suit environment
- 10 to 15 seconds drying time with automatic shut-off when not in use
- Manufactured from 1.2mm grade 304 stainless steel to protect against corrosion and vandalism with low noise level of 72dB
- Self-resetting overheat thermostat provides protection from overheating if hand dryer becomes blocked
Safety Instructions
- These instructions should be read carefully and retained after installation for future reference and maintenance.
- Ensure that the mains power is switched off before carrying out installation or maintenance.
- Installation must be carried out in accordance with the current edition of IET wiring regulations BS 7671, and by a qualified electrician.
- The hand dryer should be supplied from a switched fused spur. This Hand Dryer is electrical class 1 construction and must be earthed.
- Ensure all electrical connections are secure and that there are no loose strands.
- Do not install above washbasins or immediately adjacent to urinals, lavatories, baths and showers.
- When in use, the hand dryers will accumulate dust. Cleaning and maintenance must be carried out regularly.
- The unit is intended for drying hands only. Long hair should be kept away from air inlet vents.
Environmental Instructions
This product may contain substances that can be hazardous to the environment if not disposed of properly. Electrical and electronic equipment should never be disposed of with general waste but must be separated for its correct treatment and recovery. Where possible recycle your packaging.
Installation Instructions
- Remove the front cover by removing the securing screws at the base of the hand dryer.
- Using the base as a template, mark out the fixing holes on the mounting surface. See Fig 1.
- Feed the supply cable through the hole in the base and terminate the conductors into the terminal block ensuring the correct polarity is observed. See Fig 2.
- Secure the supply cable in the cord grips provided
- Secure the base to the mounting surface using the wall plugs and screws supplied.
- Offers the cover back to the base and secure in position using the securing screws.
Operation
The hand dryer is automatically activated when hands are placed under the air outlet. Once the hands are removed, the hand dryer automatically switches off within 2 seconds. If the hand dryer is running continuously, it will switch off after 60 seconds to conserve energy. To reactivate the hand dryer, move the hands away from the air outlet and place back.
Specification
- It is recommended that the HEPA filter is replaced every 6 months
INS0014 V2.0 08/23 NPD0385 T11
Deta Electrical Company Ltd
- UK: Panattoni Park Luton Road Chalton Bedsfordshire LU4 9TT
- EU: Unit 16 Ashbourne Industrial Estate, Ashbourne Co. Meath, A84 W972, Ireland deta.co.uk
- Technical Helpline : +44(0)1582 544 548