deta 1012WH High Speed Automatic Hand Dryer Instruction Manual

data 1012WH  High  Speed Automatic Hand Dryer

Product Information

Specifications

• Input Voltage:
• Air Speed : 100m/s
• Electrical Classification : Class I
• Noise Level (at 2m) : 75dB
• Rated Power: Heater Element – 1200W, Motor – 600W
• IP Rating : IPX1
• Weight : 4.6kg
• Drying Time : 10-12 seconds
• Dimensions: 325x250x175mm

Features

• High-Speed Automatic Hand Dryer
• Available in White and Stainless Steel variants (1012WH and 1012SS)

Safety Instructions

This product may contain substances that can be hazardous to the environment if not disposed of properly. Electrical and electronic equipment should never be disposed of with general waste but must be separated for its correct treatment and recovery. Where possible, recycle your packaging.

Environmental Instructions

This product should be disposed of properly to prevent harm to the environment. Please separate it from general waste and follow the correct treatment and recovery processes. Recycle the packaging whenever possible.

Installation Instructions

1. Remove the front cover by removing the security screws on the sides of the hand dryer.
2. Using the base as a template, mark out the fixing holes on the mounting surface.
3. Fix the base of the hand dryer on the mounting surface using the wall plugs and the screws provided.
4. Feed the supply cable through the hole in the base and terminate the conductors into the terminal block ensuring the correct polarity is observed.
5. Secure the supply cable in the cord grip and terminate the conductors into a spur.
6. Replace the front cover back on the base and secure it in position using the security screws.

Operation

The hand dryer is automatically activated when hands are placed under the air outlet. Once the hands are removed, the hand dryer automatically switches off within 2 seconds. If the hand dryer is running continuously, it will switch off after 60 seconds to conserve energy. To reactivate the hand dryer, move the hands away from the air outlet and place them back.

FAQ

• Q: What should I do if the hand dryer becomes blocked?
• A: If the hand dryer becomes blocked, please follow the installation instructions to remove the front cover and clean any obstructions.

MODELS

High-Speed Automa

Features

• Manufactured from 1.2mm grade 304 stainless steel to protect against corrosion and vandalism with a low noise level of 75dB
• An -tamper cover (fixing screws included)
• 10-12 seconds drying me
• Constructed with sound and vibra on reducing blocks to reduce noise level
• Automa C shuts off aer 60 seconds to avoid wasted energy
• Self-rising overheating thermostat protects overhead ng if the hand dryer becomes blocked

Safety Instructions

1. These instructions should be read carefully and retained after installation for future reference and maintenance.
2. Ensure that the mains power is switched off before carrying out installation or maintenance.
3. Installation must be carried out in accordance with the current media on of IET wiring regulations BS 7671, and by a qualified electrician.
4. The hand dryer should be supplied from a switched fused spur.
5. This Hand Dryer is an electrical class 1 construction and must be earthed.
6. Ensure all electrical connections are secure and that there are no loose strands.
7. Do not install above washbasins or immediately adjacent to urinals, lavatories, baths and showers.
8. When in use, the dryers will accumulate dust. Cleaning and maintenance must be carried out regularly.
9. The unit is intended for drying hands only. Long hair should be kept away from air inlet vents.

Environmental Instructions

This product may contain substances that can be hazardous to the environment if not disposed of properly. Electrical and elec tronic equipment should never be disposed of with general waste but must be separated for its correct treatment and recovery. Where possible recycle your packaging.

Installation Instrucions

1. Remove the front cover by removing the security screws on the sides of hand dryer.
2. Using the base as a template, mark out the fixing holes on the main surface.
3. Fix the base of the hand dryer on the moun ng surface using the wall plugs and the screws provided.
4. Feed the supply cable through the hole in the base and terminate the conductors into the terminal block ensuring the correct polarity is observed.
5. Secure the supply cable in the cord grip and terminate the conductors into a spur.
6. Replace the front cover back on the base and secure it in position using the security screws.

Operation

The hand dryer is automatically activated when hands are placed under the air outlet. Once the hands are removed, the hand dryer automatically switches off within 2 seconds. If the hand dryer is running connuously, it will switch off after 60 seconds to conserve energy. To reach vote the hand dryer, move the hands away from the air outlet and place them back.

• Deta Electrical Company Limited
• UK: Panattoni Park, Luton Road, Chalton, Bedfordshire, LU4 9TT
• EU: Unit 16 Ashbourne Industrial Estate, Ashbourne, Co. Meath, A84 W972, Ireland
• deta.co.uk
• Technical Helpline: +44(0)1582 544 548

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>