MOUNTUP MU0058 Full Motion TV Wall Mount Installation Guide
- June 16, 2024
- MOUNTUP
Table of Contents
MOUNTUP MU0058 Full Motion TV Wall Mount
If you have any questions, please feel free to contact Customer Service via Amazon before returning.
Safety Caution
Please read this instruction carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.
- This product is designed for use in wood stud or solid concrete wall.
- DO NOT install into drywall alone.
- The wall must be capable of supporting five times the weight of the TV and mount combined.
- Incorrect installation may result in product damage / property damage or body injury. We shall bear no responsibility for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; please contact our customer service team. Never use damaged parts!
Must Check Before Getting Started
Minimum VESA Pattern (W × H): 150mm × 100mm / 6 in × 4 in
Maximum VESA Pattern (W × H): 600mm × 400mm / 24 in × 16 in
WARNING
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only within the maximum weights
indicated. Use with products heavier than the maximum weights indicated may
result in failure of the mount and its accessories, causing possible damage
or injury.
Verify Your Wall Construction
Perfect
CAUTION :
Avoid potential personal injuries and property damage!
Drywall covering the wall must not exceed 5/8 in. (16 mm).
Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1 ½ x 3 ½ in.
(38 x 89 mm)
Perfect
CAUTION :
Avoid potential personal injuries and property damage!
Mount the wall plate assembly directly onto the concrete surface (no surface
covering).
CAUTION: DO NOT install into drywall alone.
Product Dimensions
Supplied Parts and Hardware
-
Mount 01 ×1
-
Brackets 02 ×2
-
Arm Extensions 03 ×4
-
Side Cover 04 ×2
Wall / Product
Lag Bolt ST8x65mm A x4|
wrench S10mm B x1
TV
- Philips Screws
M4 x 12mm
M4 x 30mm
×4 ×4 MA
- Philips Screws
M6 x 15mm
M6 x 30mm
×4 ×4 MB
- Philips Screws
M8 x 25mm
M8 x 45mm
×4 ×4 MC
- Spacers
H10mm
×8 MD
-
Washers
Ф6mm
M4-5-6
×4 ME -
Spacers
H5mm
×8 MF
-
Bubble Level T1 ×1
-
Velcro Cable Ties T2 ×3
-
Mounting Template T3 ×1
NOTE: Not all parts and hardware included will be used.
Extra Tools You Need (Not Supplied)
-
Band Tape
-
Pencil
-
Electro drill
-
Socket Wrench
-
Screwdriver
Attach Brackets to TV
Select TV Screws
|
---|---
-
Too Short
-
Too Long
-
Not Vertical
-
Correct
-
Correct
Need Spacer?
-
Yes, choose the appropriate screws, washers,and spacers for your TV.
-
For more spacing between bracket and TV
-
For protruded back TV
-
For counterbore of TV
-
To avoid the blocked input
-
No, just choose the screws, washers.
| Do not tighten the screws
excessively or tighten them by using the Electro drill, or your TV might be
damaged.
---|---
Assemble the Mount
Attach Wall Plate to Wall
OPTION A:
Wood Stud Installation
-
A-1
Locate your studs. Verify and mark the center of the stud by finding the stud edges using awl and stud finder.
Line up the holes with your stud center line. Level the mounting template and mark the pilot hole locations.
-
A-2
Drill pilot holes using a
Ф7/32 in (Ф5.5mm) diameter drill bit
IMPORTANT:
Do not drill holes into where water pipes or electrical wires are located. Be sure to drill into the center of the stud. -
A-3
CAUTION : Do not use in drywall or wood stud!
Install wall plate using lag bolts with Socket A Wrench, NO Electro drill.
No anchors when installed onto the wood studs.
CAUTION:
To avoid potential personal injury or property damage:
All 4 lag bolts A MUST BE firmly tightened to prevent unwanted movement of
the wall plate assembly. Ensure the wall plate assembly is securely fastened
to the wall before continuing on to the next step. To prevent the TV falling
down, the Arrow Must Keep UP at this step!!
Attach Wall Plate to Wall
OPTION B:
Solid Concrete Wall Installation
-
B-1
Level the mounting template and mark the pilot hole locations. -
B-2
Drill pilot holes using a
Ф3/8 in (Ф10mm) diameter drill bit.
IMPORTANT :
Do not drill holes into where water pipes or electrical wires are located, or mortar between blocks. -
B-3
Use the hammer to knock anchors (not included) into the concrete wall. Be sure the anchors are seated flush with the concrete surface.
Install wall plate using lag bolts A and anchors (not included) with Socket Wrench, NO Electro drill.
CAUTION
To avoid potential personal injury or property damage:
All 4 lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate assembly. Ensure the wall plate assembly is securely fastened to the wall before continuing on to the next step. To prevent the TV falling down, the Arrow Must Keep UP at this step!!
Hang and Secure TV to Wall Plate
-
4-1
Before hanging TV, please conduct “wall plate installation integrity test” first.
-
4-2
Hang and secure TV assembly onto the wall plate.
Adjustments
Leveling Adjustment
If needed, TV can be leveled ±3 degrees via adjusting the 4 nuts with the wrench (B).
Tilt Adjustment
- Loosen the tilting nuts ×2.
- Adjust TV to your desired angle.
- Retighten the nuts to fix the intended angle.
Lock TV in Place / Unlock
Documents / Resources
|
MOUNTUP MU0058 Full Motion TV Wall
Mount
[pdf] Installation Guide
MU0058, MU0058 Full Motion TV Wall Mount, Full Motion TV Wall Mount, Motion TV
Wall Mount, TV Wall Mount, Wall Mount, Mount
---|---
|
MOUNTUP MU0058 Full Motion TV Wall
Mount
[pdf] User Manual
MU0058 Full Motion TV Wall Mount, MU0058, Full Motion TV Wall Mount, Motion TV
Wall Mount, TV Wall Mount, Wall Mount
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>