MOUNTUP MU4005 Dual Monitor and Laptop Mount Instruction Manual

MOUNTUP MU4005 Dual Monitor and Laptop Mount

If you have any questions, please feel free to contact our customer service via Amazon before returning.

WARNING!
If you have any questions, please feel free to contact Customer Service via Amazon before returning.

Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation, such as the use of the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.

The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF THE REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

NOTE: Not all hardware included will be used.

ASSEMBLY STEPS

STEP 1: Apply Pads To The Base Bottom

• Paste the Pad (F1) onto the Base (F)

STEP 2: Clamp Installation Or Grommet Base Installation

• OPTION A: Clamp Installation
  Align the screw hole on the Base (F), then lock the Screw (B3) with a 5mm Allen Key (K). Put the Clip Plate (B-1) on the Bolt Y (B2)

  • Fix the bracket on the table by tightening the Clamp (B), then fix the Decorative Cover (C) to the Base (F).

• OPTION B: Grommet Base Installation
  Ensure the desktop has a hole between 0.39″-2.36″ (10mm-60mm) in diameter to use this option.

  • Use 5mm Allen Key(K) to detach Bolts(B3)and Bolt Y(B2) from Clamp(B).
  • Use Bolt Y (B2) through the screw hole on Bracket (B1) to fix the base (F) and the table board together. Then fix the Decorative Cover (C) to the Base (F).

STEP 3: Arm Installation

• 1-1: Install Wire Clip (G1) to Middle Arm (G).
• 1-2: Install Plastic Parts (1) to Middle Arm (G).
• 1-3: Install the Middle Arm (G) to the pole, then Lock the bolt on the Middle Arm(G) with the supplied 6mm Allen key(L).
• 2: Install Wire Clip (F2) and Swivel Arm (A) to the pole. Lock the bolt on the Swivel Arm (A) with the supplied 6mm Allen key (L).

STEP 4: Front-panel Installation
Install the Laptop Tray (E) to the Middle Arm (G), and Apply pads (E1) to the Laptop Tray (E) to avoid laptop scratches.

1. 1. Install the top two screws first

2. And then you attach the Laptop Tray (E) to the Middle Arm (G)
3. Finally, install the next two screws and tighten all screws

STEP 5: Attach Monitor

OPTION A: Flat Back Monitor
Attach the VESA plate (D) to the back of the monitor and secure it by using a 5mm Allen Key (K) to tighten screws (M-A) along with washers (M-C).

Do not tighten the screws excessively or your monitor might be damaged.

OPTION B: Curved Back Monitor
Attach the VESA plate (D) to the back of the monitor and secure it by using a 5mm Allen Key (K) to tighten screws (M-A) along with washers (M-C) and Spacer (M-D).

Do not tighten the screws excessively or your monitor might be damaged.

NOTE:
Hand-tighten screws to avoid over-tightening.

STEP 6: Hang Monitor

• Slide the monitor onto the head of Swivel Arm (A). Install the Security Bolt (H).
• Make sure the security bolt is tightened before you rotate the monitor.

STEP 7: Tilt Adjustment

1. Slightly loosen the tilting bolt.
2. Adjust the monitor and laptop tray to your desired tilt angle.
3. Retighten the tilting bolt to secure the monitor and front panel in place.

STEP 8: Gap Spring Tension Adjustment
For the intended functioning of the mount, you may need to adjust the tension of Arm (A) following your monitor weight by 6 mm Allen Key (L).

Note 1:
Be sure to keep the arm in a horizontal position during adjustment. Or else it would be difficult to adjust the mount or damage the mount.

• Situation 1: Arm falls down
  The Upper Arm with the monitor falls and fails to stay where intended.
  Solution:
  Turn the inside screw counterclockwise(“+” direction) to increase gas spring tension until the arm can stay as intended.

• Situation 2: Arm rises up
  The Upper Arm with the monitor rises and fails to stay where intended.
  Solution:
  Turn the inside screw clockwise(“-” direction) to decrease gas spring tension until the arm can stay as intended.

Note 2:
For how many circles the screw should be turned, please refer to the table below.

STEP 9: Cable Management
Run cables through the cable cover as shown in the diagram.

Adjust as Desired

Adjust monitor position and rotation.

Note:
To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate.

Suggestion:
Please attach the monitor first, then hold the two sides of it with both hands and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.

Product Dimensions

CAUTION AND MAINTENANCE

• Don’t allow children to climb, stand, hang, or play on any part of the monitor or stand.
• This product is intended for indoor use only. Using this product outdoors may lead to product damage or personal injury.
• Check if the bracket is secure and safe to use at regular intervals (at least every three months).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>