TECNO PHANTOM V Yoga Android Smart Phone User Manual

TECNO PHANTOM V Yoga Android Smart Phone

Specifications

• CTP+LCM 6.9 MOD 3 F HSG ASM UP 5 32M FCAM 7 P SENSOR PCB 9 REC FRAME 11 FLASH FPC 13 MAGNET UP 15 FP FPC 17 MIC PC 19 F-FLASH LAMP COVER 21 HING ROTATE DECO 23 FLASH FPC STEEL 25 SCREW M14_D25_L35 27 SCREW M14_D25_L50 29 NFC FRAME 31 BATTERY DECO FRAME STEEL 33 MAIN FPC CONN STEEL 35 AMBIENT RUBBER 37 EXTERNAL LCM ASM 39 BATTERY COVER DOWN

• UP BEZEL 4 MAIN PCBA 6 FCAM FRAME 8 PS LAMP COVER 10 REC 12 F-FLASH PCB 14 SIM ASM 16 ANT FPC 18 SENSOR PC 20 NFC 22 HING ROTATE 24 SCREW M12_D25_L25 26 SCREW M14_D25_L45 28 REAR FRAME UP 30 MAIN FPC HOLDER 32 BATTERY DECO FRAME 34 BATTERY FPC HOLDER 36 64M RCAM 38 BATTERY COVER UP 40 RF FPC 41 13M RCAM 43 HING ROTATE RUBBER 45 SCREW M14_D25_L30 47 USB
  RUBBER 49 LCD FPC 51 REAR FRAME DOWN 53 MAIN FPC 55 SIDEKEY ASM 57 FP ASM 59 HING ROTATE SUB MAGNET 61 MAGNET DOWN 63 POWER KEY FPC 65 BATTERY DOWN 67 TYPE-C 69 DOWN BEZEL

• 42 SPRING COPPER 44 HING ROTATE BEZEL 46 SCREW M14_D25_L25 48 SPK FRAME 50 SPK RUBBER 52 DOWN MIC RUBBER 54 MAIN FPC STEEL 56 FPC RUBBER SLEEVE 58 HING ROTATE MAGNET 60 HALL MAGENET 62 VOL KEY FPC 64 BATTRY UP 66 VC 68 F HSG ASM DOWN

Know your phone

• Front camera
• Volume + key
• Volume – key
• Power key & side fingerprint sensor
• NFC

SIM/SD card installation

1. Power off the mobile.
2. Refer to the following picture for SIM / SD card installation.

Explosion diagram specification

Know your phone

Front camera

1. Volume + key
2. Volume – key
3. Power key & side f
4. ngerprint sensor
5. NFC

SIM/SD card installation

1. Power off mobile.
2. Refer to the following picture for SIM / SD card installation.

Charging the phone

You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone).
Use only TECNO charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.

FCC Caution

Labelling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Information to user.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• I ncrease the separation between the equipment and receiver.
  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) information
This mobile phone meets the government’s requirements for exposure to radio waves.

The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.

FCC RF Exposure Information and Statement
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: AD11 (FCC ID:2ADYY-AD11) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.145W/kg and when properly worn on the body is 1.440W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10 mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10 mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that does not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.

Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

HiOS runs on AndroidTM OS. Android is a trademark of Google LLC.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>