INMOTION M3 Wireless Waterproof Speaker User Guide

INSTRUCTIONS
WIRELESS WATERPROOF
SPEAKER

M3 Wireless Waterproof Speaker

1. Lanyard slot (lanyard not included)
2. AUX in port
3. USB-C charging port
4. Charge indicator
5. Power button
6. Volume down
7. Play button
8. Volume up
9. Mode button
10. BT indicator
11. Microphone

NOTE BEFORE USE

This product is designed with full attention for safety performance. To ensure safe operation, please follow the following rules:

1. Place the speakers in a stable position to avoid falls and damage or personal injury.
2. Do not drop, disassemble, open, crush, bend, puncture or burn the speaker.
3. Do not place speaker near any heat source (such as radiators, heating equipment, stoves, or other heat-generating equipment).
4. Before wiping with a dry cloth to clean the speakers, set the power switch to the off position and unplug the power cord from the power outlet.
5. Please adjust the sound to a suitable level to avoid damage to your ears.

SAFETY INSTRUCTIONS

Read all instructions
Only charge with devices rated and marked with 5V to avoid damage to the speaker.
Do not open the speaker, it may damage the product
Rechargeable batteries have a limited number of charge cycles. Battery life and number of charge cycles varies by use and settings. Never place the speaker close to high temperature heat sources.
Never try to repair the product yourself.
Charging
Connect the supplied charging cable to the USB-C charging port and connect the other end to the USB-A port of the power supply. The charging indicator turns red during charging and off when fully charged. It is recommended to charge 1 0 minutes before powering on the speaker if it has been unused for 7 days.
Power ON/OFF
Press and hold the power button for approx. 3 seconds to turn on the speaker. The BT indicator flashes and is ready for BT pairing.
Press and hold the power button for approx. 3 seconds again to turn off the speaker. The BT indicator is now off.
Pairing
Turn on the speaker and the BT indicator flashes. Enable the BT search on your device and select “ln Motion” from the list. It will give an indication sound when connection is successful. The BT indicator will stay on. Only one BT device can be connected at the same time. If you want to connect another device, you need to disconnect the current one first.
Reconnection
The speaker will automatically connect to a device which is previously paired and supports automatic reconnection.
When it is not connected, long press the Mode button to reconnect.
Press and hold the Mode button for 3 seconds to disconnect.
AUX connection
Connect the provided 3.5mm audio cable to the speaker and your device.
Playing Mode
The speaker supports playback through BT and AUX.
Press the Mode button once to switch between them.
The Play Button Function
Short Press:

1. Music playback, play/pause function
2. Answer an incoming call
3. Hang up a call

Long Press:

1. Press and hold for 2 seconds to reject a cal I
2. Press and hold for 2 seconds to enter TWS (True Wireless Stereo) connection (see details on TWS Connection section). Once connected, press and hold 2 seconds to disconnect.
3. Press and hold for 5 seconds to clear the pairing information and return to default volume with a beep, the speaker will automatically turn off.

Double Press
To call back the last call when the speaker is connected to your phone via BT.
Change Volume and Song
During playback
Press Volume Up Button once to increase the volume.
Press Volume Down Button once to decrease the volume.
Long press Volume Up Button to select next song.
Long press Volume Down Button to select the previous song.
Hands Free Function
During BT connection, press the Play button once to answer the call, you can talk to each other through the built-in microphone. After call ended, it will continue to play music.
Long press the Play Button to reject an incoming call.
Voice Assistance
Short press Power Button to activate voice assistance while in BT mode with device has voice assistance function.
True Wireless Stereo (TWS) Connection
The speaker can connect to a same model speaker for Stereo sound.

1. Turn on both speakers
2. Press and hold the Play button on one of the speakers for about 2 seconds until you hear a “beep” sound. This speaker becomes the primary speaker.
3. Release the Play button. It may take a few more seconds before speakers connect to each other.
4. Check the indicator lights to distinguish L/R channel: The BT indicator of the primary speaker will flash blue for every 3 seconds that should be the Left channel; the BT Indicator on the other speaker stay on that should be the right channel.
5. Enable the BT search on your device and pair the speakers by selecting “lnMotion”. It will only display one speaker which is both speakers combined.
   To disconnect TWS connection, press and hold the Play Button on one of the speakers for 2 seconds until you hear a “beep” sound.

Automatic Turn Off
The speaker will turn off automatically in 1 0 minutes when Bluetooth is not connected and there’s no playback.

Technical Specification

Range: Up to 1 Om
Speaker unit: o52 mm (2.05 in.), 5W
Impedance: 40
Input: DC 5V/800mA
Waterproof level: IPX7
Built-in rechargeable battery: Li-ion, 3. 7V, 1200mAh
Charging Time: 3 hours
Playing time: Up to 5 hours (100% sound volume)
Product size: o 90 X 75mm (o 3.54 x 2.95in.)
Weight: 227g (8.0 oz)
USBC to USBA charging cable length: 45cm (17.7 in.)
AUX to AUX cable length: 1 m (39.3 in.)

FCC COMPLIANCE

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna  Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio / TV technician for help ISED Canada Compliance
  This device complies with Industry Canada licence-ex­ empt RSS standard(s).

Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
InMotion” is owned by lnMotion Entertainment LLC.
Colors and content may vary.
Please retain this information for future reference.
UK: WH Smith SN3 3RX UK
USA: IMEG LLC, 3755 W Sunset Rd
Suite A, Las Vegas, NV 89118
EU: WH Smith Ireland Limited, 6th Floor,
2 Grand Canal Square, Dublin 2, ROI
AU: WH Smith Australia, Level 4,
80 William Street, Woolloomooloo, 2011 NSW,
Sydney, Australia
Produced in China

Print colours
BLACK
Additional/Special Finishes
Cutter/Crease & Perforation Guides
CUTTER
GUIDE
SIGN OFFS
PM (colour breakdown/copy):————————-
Designer (design):———–
QC (quality copy):———-
Buyer (all elements):————-
Date sent to print’—————–
Please note this run out is not a cromalin or colour proof. This run out should ONLY be signed when all the copy has been checked and is correct, and the colour breakdown, cutter dimensions and design checked and approved.
Any corrections to be made should be marked on this run out and returned unsigned. Artwork will not be released until signed approval is received.
It is not WHSmith policy to send out fonts. To purchase our fonts, please contact Agfa Monotype on 0800 371242 or visit www.agfamonotype.co.uk
© WH Smith pie and its subsidiaries, 2017. All rights reserved. The contents of this artwork are not to be reproduced, copied or transmitted in any form or by any means without the consent of the copyright owner.
PLEASE NOTE ALL AMENDS MADE AFTER
SIGN-OFF WILL INCUR ADDITIONAL SBU COSTS
WHSmith
Tel 01793 616161
Ftp: whsmith .wam net com
WHSmith, Greenbridge Road, Swindon, Wiltshire SN3 3RX

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>