INMOTION K200-HV Series Radio Remote Control Owner’s Manual

May 15, 2024
INMOTION

INMOTION K200-HV Series Radio Remote Control

INMOTION K200-HV Series-Radio-Remote-Control-product-
image

Product Information

Specifications

  • Brand: Inmotion Controls, Inc.
  • Model: K Series Transmitter
  • Versions: 2, 4, 6, or 8 pushbuttons
  • Features: 2-step pushbuttons

Product Usage Instructions

Chapter 1: Customer Information
Thank you for purchasing an Inmotion Controls, Inc. radio remote control. Make sure to read all instructions carefully before mounting, installing, and configuring the product. The manual provides general information on operating the radio remote control transmitter.

FCC Part 15 Compliance
This device complies with Part 15 of the FCC Rules. It must not cause harmful interference and must accept any interference received. Any unauthorized changes or modifications could void your authority to operate the equipment.

IC Statement
This device complies with Industry Canada license-exempt RSS standard(s). It must not cause interference and must accept any interference that may affect its operation.

Chapter 2: General Description
The K series transmitter is available in different versions with varying pushbutton configurations. It also includes 2-step pushbuttons that can control different functions such as movement speed.

Start/Horn Switch
The Start/Horn pushbutton on the left side of the transmitter serves two functions: starting and activating the horn during operation.

Starting the Transmitter

  1. Turn to release the Emergency Off button.
  2. Press the START button to initiate operation.

Turning Off the Transmitter
To turn off the transmitter, fully press the Emergency Off button. This action deactivates all relays and turns off the transmitter.

FAQ

Guarantee, Service, Repairs, and Maintenance

  1. Q: What is covered by the guarantee/warranty?
    A: The guarantee covers material, construction, and manufacturing defects. Inmotion Controls, Inc. may replace faulty products or parts during the warranty period.

  2. Q: What is not covered by the guarantee/warranty?
    A: The guarantee does not cover normal wear and tear, consumable parts, unauthorized modifications, incorrect installation or use, condensation, and water damage.

  3. Q: Who should carry out repairs and maintenance?
    A: Qualified personnel should conduct repairs and maintenance using spare parts from Inmotion Controls, Inc. Keep the product in a dry, clean place and ensure contacts and antennas are clean.

Guarantee, service, repairs and maintenance

Inmotion Controls, Inc. products are covered by a guarantee/warranty against material, construction and manufacturing defects. During the guarantee/warranty period, Inmotion may replace the product or faulty parts. Work under guarantee/warranty must be carried out by Inmotion Controls, Inc.

The following are NOT covered by the guarantee/ warranty:

  • Faults resulting from normal wear and tear
  • Parts of a consumable nature such as pushbuttons, relays, fuses etc.
  • Products that have been subject to unauthorized modifications
  • Faults resulting from incorrect installation and use
  • Condensation and water damage

Maintenance:

  • Repairs and maintenance must be carried out by qualified personnel.
  • Use spare parts from Inmotion Controls, Inc. only.
  • Contact your representative if you require service or other assistance.
  • Keep the product in a dry, clean place.
  • Keep contacts and antennas clean.
  • Wipe off dust using a slightly damp, clean cloth.

Customer Information
Thank you for purchasing an Inmotion Controls, Inc. radio remote control.
READ ALL INSTRUCTIONS CAREFULLY BEFORE MOUNTING, INSTALLING AND CONFIGURATING THE PRODUCT.
This manual includes general information concerning the operation of the radio remote control transmitter.

General Information on Safety

  • Persons under the influence of drugs and/or alcohol and/or other medicine that impairs their reaction may not assemble, disassemble, install, put into operation, repair or operate the product.
  • All conversions and modifications of an installation/system must conform to the relevant safety requirements. Work on the electrical equipment must be performed only by qualified, authorized personnel and in accordance with the relevant safety requirements.
  • In the event of malfunctioning, visible defects or irregularities, the product must be stopped, switched off and the relevant master switches must be switched off.

Symbols and Definitions for Warnings
Warning against hazardous situation
Warning against electrical voltage

FCC Part 15 (FCC ID: RN489896162JK01)

  • This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

European Union Regulatory Notice
This device bearing the CE marking is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
This device complies with the following harmonized European standards. Safety: EN 60950-1:2006+A11:2009+A1:2010+A12:2011
EMC: ETSI EN30 1489-1 V1.9.2 2001-09; ETSI EN 301 489-3 V1.4.1 2002-08
Radio: ETSI EN 300 220-1 v2.4.1: 2012; ETSI EN 300 220-2 v2.4.1: 2012
The following CE marking is valid for EU harmonized telecom products.
IC Statement (IC: 10821A-8989616201)
This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions:

  1. this device may not cause interference, and
  2. this device must accept any interference, including interference that may cause undesired operation of the device.

General Description

The K series transmitter comes in different versions, featuring 2, 4, 6, or 8 pushbuttons. The transmitter also features 2-step pushbuttons. Both steps of each pushbutton can operate different functions like controlling the speed of a movement, step 1: slow, step 2: fast.

INMOTION K200-HV Series-Radio-Remote-Control-\(3\)

Start/ Horn switch
The K series transmitter has a Start/Horn pushbutton on the left side.

The Start/Horn switch has 2 functions:

  1. Press to Start.
  2. Press for horn while operating.

INMOTION K200-HV Series-Radio-Remote-Control-\(4\)

Start the transmitter in operating mode

  1. Turn to release the Emergency Off button.
  2. Press the ”START” button.

Turning the transmitter off
Turn the transmitter off by completely pressing the Emergency Off button. The transmitter turns off. All relays deactivate.

Changing the batteries:
BATTERY TYPE: 2 x 1.5V(LR6 AA)

INMOTION K200-HV Series-Radio-Remote-Control-\(7\)

Technical Data

Transmitter

Frequency Range 433.0525~434.7775MHz
Modulation method 4FSK
Typical operating range 300 feet
Control system PLL (Phase Lock Loop)
Antenna impedance 50 ohms
Typical response time for commands 50ms~100ms
Power Supply LR6 (AA) 1.5Volt x 2
Antenna Internal
Average power consumption 16ma@3VDC (default setting)
Radio-frequency power <10dBm (default setting)
Operating and storage temperature -4°F ~ 131°F / -40°F ~ 149°F
Protection rating IP65
Dimensions 7.63” x 2.25” x 2.00” (2-8 buttons)
Weight (including battery) Approx. 11.46 ounces
Housing material PA6 (30% Glass Filled)

Receiver

WARNING: The receiver must NOT be opened by any other than a qualified installer. Make sure to turn the electricity off before opening the receiver.

Technical Data
Receiver

Frequency 433.0525~434.7775MHz
Modulation Method 4FSK
Sensitivity -112dBm@baud 1.2K bps
Control System PLL
Antenna impedance 50 ohms
Typical response time for commands 50mS ~ 100mS
Power Supply 12 ~ 24V AC/DC
Antenna Internal
Standby power 16mA @ 220VAC
Operating and storage temperature -4°F~131°F/-40°F~149°F
Protection degree IP 65
Dimensions 5.59” x 5.55” x 2.30”
Weigh 1.76 Lbs.
Housing material PA6 (30% Glass Filled)

WARNING: DO NOT FLUSH MOUNT THE RECEIVING ASSEMBLY. PLEASE MAINTAIN PROPER CLEARANCE AS SHOWN. PLEASE USE THE SUPPLIED MOUNT!

INMOTION K200-HV Series-Radio-Remote-Control-\(9\)

K200-HV Wiring Diagram

K400-HV Wiring Diagram

Receiver Dimensions (Not to scale)

Troubleshooting

Transmitter

INMOTION K200-HV Series-Radio-Remote-Control-\(13\)

Receiver
Should an error occur, the LED of the receiver will indicate the cause.

INMOTION K200-HV Series-Radio-Remote-Control-\(14\)

  • invalid data (from a different transmitter) received.

Accessories

Pushbutton Protector

Waterproof Case

INMOTION K200-HV Series-Radio-Remote-Control-\(18\)

Lanyard
INMOTION Controls, Inc.
Website: www.inmotioncontrols.com
888-501-2220

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals