Timegyro Alarm Clock for Bedrooms User Manual
- June 16, 2024
- Timegyro
Table of Contents
Timegyro Alarm Clock for Bedrooms
Digital alarm clock
Elements
- A: Display (Fig. 1):
- A 1: Alarm symbol A 2: Time / wake-up time
- A 3: P (12-hour system) A 4: Snooze symbol
- B: Back (Fig. 2):
- B 1: SNOOZE/AL STOP sensor button B 2: DIM switch
- B 3: TIME SET button B 4: AL SET button
- B 5: RESET button B 6: MIN/AL ON/OFF button
- B 7: HOUR/12/24 button B 8: Battery compartment
Getting started
- Open the battery compartment and insert four new AA 1.5 V batteries, polarity as illustrated.
- The device will alert you with a beep.
- Close the battery compartment again.
- Noon appears on the display.
Settings
12-HR or 24-HR system
- In normal mode, press the HOUR/12/24 button to select 12 (P appears on the display after 12 h) or 24-hour mode.
Time setting
- Press the TIME SET button.
- The time flashes on the display.
- Press the HOUR/12/24 button to adjust the hours.
- Press the MIN/AL ON/OFF button to adjust the minutes.
- Confirm the setting with the TIME SET button.
Alarm time setting
- Press the AL SET button.
- The alarm time (default 6:00) flashes on the display.
- Press the HOUR/12/24 button to adjust the hours.
- Press the MIN/AL ON/OFF button to adjust the minutes.
- Confirm the setting with the AL SET button.
- The alarm symbol and the snooze symbol appear on the display.
- Both functions are now activated.
Alarm functions
Alarm clock function
- Press the MIN/AL ON/OFF button in normal mode, to activate or deactivate the alarm function.
- When the alarm is activated, the alarm time appears for 3 seconds.
- The alarm symbol remains on the display.
- When the adjusted alarm time is reached, the alarm rings.
- Press the SNOOZE/AL STOP sensor button to turn off the alarm sound.
- If the alarm is not stopped manually, the ascending alarm tone automatically turns off after one minute and the alarm will be reactivated at the same set time on the following day.
- The alarm symbol remains on the display.
- Press the MIN/AL ON/OFF button in normal mode, to deactivate the alarm function. The alarm symbol disappears.
Snooze function
- To activate the snooze function press and hold the HOUR/12/24 button for 2 seconds in normal mode. The snooze symbol will appear on the display.
- When the adjusted alarm time is reached, the alarm rings.
- Press the SNOOZE/AL STOP sensor button to activate the snooze function.
- The snooze symbol flashes on the display.
The alarm will be interrupted for 7 minutes.
- You can activate the snooze function up to 3 times.
- Press any button to turn off the snooze function.
- To deactivate the snooze function, press the HOUR/12/24 button for 2 seconds in normal mode. The snooze symbol will disappear.
Display light
- Move the brightness adjusting switch DIM to change brightness in 3 steps (HIGH-MIDDLE-LOW).
- Automatic night backlight: the light is dimmed between 20:00 and 6:00.
Dots between the hour and minute indicators
- The two dots between the hour and minute indicators flash every second on the display.
- To activate or deactivate the function press the MIN/AL ON/OFF button for 2 seconds in normal mode.
Care and maintenance
- Clean the device with a soft damp cloth. Do not use solvents or scouring agents.
- Remove the batteries if the device will not be used for an extended period.
- Keep the device in a dry place.
Battery replacement
- Change the batteries when the device functions become weak.
- Open the battery compartment and insert four new AA 1.5 V batteries,
- Close the battery compartment again.
RESET button
- If the unit does not work properly use a pin to press the RESET button, then the clock will return to the initial mode. The device will alert you with a beep.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>