MOUNTUP H22002 Dual Monitor Desk Mount User Manual

June 16, 2024
MOUNTUP

MOUNTUP-logo

MOUNTUP H22002 Dual Monitor Desk Mount

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-product

Information

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-1

WARNING

If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help via Amazon. Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.

The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD.ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-2

NOTE: Not all hardware included will be used.

DO NOT EXCEED WEIGHT CAPACITY.

Install the Base

OPTION A: For Clamp Mounting

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-4

  • Firstly detach Brace (E1) from C-Clamp (E) with 4mm Allen Key (L).
  • Mount Brace (E1) to the bottom of Base (A) by tightening Bolts (J) with 4mm Allen Key (L).MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-5
  • Apply Pads (lI) to the base bottom to avoid desk scratches.
  • Attach the C-Clamp (E) to the Brace (E1).
  • Then tighten the Bolts (E4) with 4mm Allen Key (L).MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-6
  • Attach the Support Plate (F) to bolts of C-Clamp (E).
  • Secure stand to the desktop by tightening Bolts (E3).
  • Finally attach the Decorative Cover (H) to the base.

OPTION B: For Grommet Mounting

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-7

  • Mount Grommet Plate (G) to Base (A) bottom with Bolts (J) and tighten by 4mm Allen Key (M).
  • Apply Pad (1) to the base bottom to avoid desk scratches.MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-8
  • Detach two Bolts (E3) from C-Clamp (E) by using 4mm Allen Key (M).
  • Run two Bolts (E3) through Support Plate (F) and Grommet Hole on desktop, then tighten the Bolts (E3) with 6mm Allen Key (M).

Install the Arms

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-9

  • Install the Lower Arm (B} and the Upper Arm (C) to the Base (A).
  • Secure the arm by tightening the set screws using 3mm Allen Key (K).

If Necessary

  • If metal sheet on plastic sleeve are lose, you can use spare metal sheet (N) for Installation as shown in diagram.

Attach Monitor

OPTION A: Flat Back Monitor

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-12

  • Attach the VESA Plate (D) to back of monitor and secure it with Screws (M-A or M-B or M-C) and Washers (M-D) using 4mm Allen Key (L).

WARNING

  • Please make sure you don’t tighten the screws much excessively or it may cause your monitor damage.

OPTION B: For Recessed / Curved Back Monitor

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-13

  • Attach the VESA Plate (D) to back of monitor and secure it with Screws (M-A or M-B or M-C), Washers (M-D) and Spacers (M-E) using 4mm Allen Key (L).
  • Put 4 spacers between VESA plate and monitor.
  • Install 4 long screws through VESA plate, spacers to monitor via mounting holes.

WARNING

  • Please make sure you don’t tighten the screws much excessively or it may cause your monitor damage.

Hang Monitor And Tilt Adjustment

Hang Monitor

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-14

Tilt Adjustment

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-15

Problem

  • If monitor faces down.

Solution

  1. Slightly loosen two preassembled bolts.
  2. Adjust monitor to your desired tilt angle.
  3. Retighten both bolts to secure the monitor in place.

Adjust Gas Spring Tension

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-16

  • For intended functioning of the mount, you may need to adjust the tension of Arm (C) in accordance with your monitor weight by 6mm Allen Key (M).

Note 1

  • Be sure to keep the arm in a horizontal position during adjustment.
  • Or else it would be difficult to adjust the mount or damage the mount.

CAUTION

  • Situation 1: Arm falls down

    • Upper Arm with monitor falls down and fails to stay where intended.
  • Solution: Turn the inside screw counterclockwise(“+”direction) to increase gas spring tension until the arm can stay as intended.

  • Situation 2: Arm rises up

    • Upper Arm with monitor rises up and fails to stay where intended.
  • Solution: Tum the inside screw clockwise(“-“direction) to decrease gas spring tension until the arm can stay as intended.

Note 2: For how many circles the screw should be turned, please refer to the table below.

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-24

Route Cables along the Arm

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-20

Adjust as Desired

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-21

+-90° Rotation

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-22

  • This function works better for monitors with the center of gravity.

Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate. Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help via Amazon.

Product Dimensions

Unit Conversion

  • 1 CM=0.39 inch

MOUNTUP-H22002-Dual-Monitor-Desk-Mount-fig-23

CAUTION AND MAINTENANCE

  • Don’t allow children to climb, stand, hang, or play on any part of monitor or stand.
  • This product is intended for indoor use only. Using this product outdoors may lead to product damage or personal injury.
  • Check if that the bracket is secure and safe to use at regular intervals (at least every three months).

If you have any questions, please feel free to contact our customer service via Amazon.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals