STRICH SPS-30 True Isolated Pedalboard Power Supply User Manual
- June 15, 2024
- STRICH
Table of Contents
SPS-30 MAX User Manual
POWER SUPPLY
SPS-30 True Isolated Pedalboard Power Supply
WARNING
Keep this manual
After reading this manual,please keep it for later reference.
Handing
To avoid breakage,do not apply excessive force to the switches or controls.
Care
If the exterior becomes dirty,wipe it with a clean,dry cloth.Do not use liquid
cleaners such as benzene or thinner,or cleaning compounds or flammable
polishes.
Keeping foreign matter our of your equipment
Never set any container with liquid in near this equipment. If liquid gets
into the equipment, it could cause a breakdown ,fire,or electrical shock.Be
careful not to let metal objects get into the equipment.If something does slip
into the equipment.unplug the AC adapter from the wall outlet. Thencontact
your nearest dealer or the store where the equipment was purchased.
Regarding disposal
Do not dispose of this product along with your household trash.By disposing
of this product correctly,you can avoid environmental harm or health risk. The
correct method of disposal will depend on your locality,so please contact the
appropriate local authorities for details.
Important notice
This product has benn manufactured according to strict specifications and
voltage requirements that are applicable in the country in which it is
intended that this product should be used.If you have purchased this product
via the internet,through mail order,and/or via a telephone sale,you must
verify thatthis product is intended to be used in the country in which you
reside.
WARNING: Use of this product in any country other than that for which it is intended could be dangerous and could invalidate the manufacturer’s or distributor’s warranty. Please also retain your receipt as proof of purchase otherwise your product may be disqualified from the manufacturer’s or distributor’s warranty.
PART NAMES AND FUNCTIONS
- SWITCH FOR LED LIGHTS: Turn the switch towards those LED lights,normally all lights would go on after the power is connected. If you don’t want all LED lights,please turn the switch back.The front panel of this unithas 8 high – brightness LED lights working as indicators,as well as lighting for Pedal Board.
- DC18V INPUT:Please plug in the output of power adapter here,and do not use adapter from elsewhere.Using power adapter without our company’s tests or certification might cause damagers to the host or other devices.On that occasion,the user must bear corresponding responsibility himself.
- OUTPUT 1-5:All DC9V power output with the maximum volume of 500mA,are suitable for ordinary analog effectors.Under the circumstances of all LED lights on,instantaneous overcurent in certain output would lead to the corresponding LED light’s flash and the currents of this channel limit to 500mA.
- OUTPUT 6 have two option of DC9V or DC12V , OUTPUT 8 have one DC18V, with the maximum volume of 1000mA, highcurrent. Under the circumstances all LED lights on, instantaneous overcurent in certainoutput would lead to the corresponding LED light’s flash and the currents of this channel limit to 1000mA.
- OUTPUT 7 have two option of DC 12V or DC18V, with the maximum volume of 500mA, highcurrent. Under the circumstances all LED lights on, instantaneous overcurent in certainoutput would lead to the corresponding LED light’s flash and the currents of this channel limit to 500mA.
*Attention: 6Black DC Cables for outlets 1-6, 2Red DC Cables for outlets 7-8.
CONNECTION METHOD
-
If the input polarity of the electrical device is ,please connect the DC Power Cable to the device directly,as shown
-
If the input polarity of the electrical device is ,please connect Polarity Reversal Cable to the DC Power Cable,then connect the device,as shown:
Attention:
Incorrect polarity would damage this unit,please make sure correct positive and negative polar before wiring.
SHORT-CIRCUIT PROTECTION
All 8 outputs in this unit have separate short-circuit protection,i.e.short circuit in one channel won’t affect other channels’ function.Under the circumstances of all LED lights on,LED light of the short-circuited channel will off,while lights in the other normal channels are stillon. This helps locating the faults when there were short circuits among many effectors.
ACCESSORIES
- Host *1pc
- DC 18V Power Adapter*1pc
- DC Power Cable 8pcs,Polarity Reversal Cable1pcs
- Manual*1pc