STRICH S3 Wireless Saxophone Microphone System User Manual

: June 15, 2024
: STRICH

Table of Contents

PRODUCT’ S INTRODUCTION
FITTING PARTS
USING GUIDANCE
PRECAUTION
Replacement Policy
Certificate of Quality
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Saxophone Wireless System
Sound Card Recording / Reverb Control

PRODUCT’ S INTRODUCTION

Thanks for your attention in our Saxophone Wireless System – S3 with STRICH brand.
Aiming at optimizing the audio curve of Saxophone, adopting the DSP Technology (Digital signal Processing), High-fidelity

UHF Communication Channel, several sets are available to use at the same time
Effective Distance is up to 40 meters without any blocks, Low Delay
The system holds the effect like Reverb, it can be adjusted for the Reverb space and Reverb Mix
Three DFS (Dynamic Frequency Scaling), Suitable for these Saxophone : Treble, E flat minor, B flat minor
Bluetooth Supported, monitor headphones, Sound card Recording, Live
Goose-neck Microphone with Silicone shock absorber , Effectvely Eliminate key sounds
Suits for most ranges of these instruments – Saxophone, Trumpet, French horn

FITTING PARTS

Transmitter
Receiver (With Cannon port)
Goose-neck Microphone
3.5mm two in one switching cable
One in two Charging cable(TYPE-C port)
Recording cable (1.5mm)

USING GUIDANCE

1.Please put the Microphone and plug into the top of the Transmitter and fix it.
2.Fix the Transmitter on the outlet of Saxophone, pull the transmitter down and push – shown as picture.
3.Bend the Microphone down, make it to the bell and stay in a best situation.
4.Put the Receiver into the amp, Sound console or Sound card, then, you can enjoy it.

1. Switch and Connection

Function	Using Guidance
Transmitter Power Switch	Transmitter(Function button) Press and hold for a

second to turn on/off, the light will be on when it’s power on while it will be off when power off.
Receiver Power Switch| Receiver (Function button) Press and hold for a second to turn on/off, The light is Cyan when it’s Matching and connecting Successfully, the light is flickering and Cyan slowly when it’s unconnected, the light is off when turn off.
Bluetooth| Transmitter(Function button) Press and hold for 3 seconds to turn on the Bluetooth and the light is Blue and flickering, Please turn on the bluetooth in your phone and search the name “DK.Audio” , and match, the light is blue when it’ s connecting successfully.
UHF Matching Connection| Transmitter(Function button) Press and hold for 35 seconds to standby for Matching while the light is Green and Flickering quickly, it’ s Green when
connected successfully. Receiver (Function button) Press and hold for a second while the light is Cyan, and it will be match automatically.
Frequency Hopping| Transmitter(Function button) Press and hold for 3 seconds to turn on the Bluetooth and the light is Blue and flickering, Please turn on the bluetooth in your phone and search the name “DK.Audio” , and match, the light is blue when it’ s connecting successfully.

2. Scene Setting
When the system is under the regular working situation, you can Press the function button shortly to switch the different setting to match the Saxophone. Both of the lights of Transmitter and Receiver are Cyan when it’ s power on and matched successfully.

Function	Light will be on always

Alto Saxophone Scene
Setting (As Default)| Cyan
Tenor Sax Scene Setting| Yellow
Soprano Sax Scene Setting| Purple

3. Reverb Effect Modes

Function	Using Guidance	Tips
Reverb Control	Under three Scene Settings, you can adjust the Reverb
Space and Reverb Mix	Scroll the button(Reverb Control), Scroll up is for

increasing the effect, Scroll down is for

4. Live Recording
When the transmitter is under the regular working situation, you can use the two in one cable with 3.55mm connector to match the Monitor headphones/Live Recording. Switching Cable – one side is for connecting Monitor headphones while one side is for connecting the Live(it can be on Live or Recording). The above is the live microphone diagram.
5. Sound Card Recording
When the transmitter is under the regular working situation, you can use the Data cable to connect the Transmitter and computer, then you can process the sound card recording.
6. Low-battery Alert
When it’ s in low battery, Please charge immediately if the light is RED.

PRECAUTION

Please read the manual before installing it or using it.
The system holds built-in battery, for better protect it, please charge it every six month.
The unit is precision electronic product, it will be regarded as giving up the warranty if it’s refit it by self.
Please keep it in Dry condition, and make sure don’ t put it in the extremely temperature.
Please keep the objects (e.g. flammable material,coin, pins),or any kind of liquids (water, soft drinks etc.) away from the system.
For further avoiding the noise or any cross talk issue, please do not use the wireless products with other brand.
Please turn off when you’re not going to use the system for along time; if there’ s any needs of charging, please use the charger supplied with 5V/500mA, in the meanwhile, if it’ s below the low battery, before charging it, please turn off the system.
Please note and check the power situation of the unit 8 hours before the performance, to make sure the equipment can be used, please charge it immediately if the power is not enough and turn off after used it.For better protecting the battery, please charge it every two or three months if you don’ tuse it ina long time, please do not keep in turning on.
Regard to the build-in battery, Please discard the used battery according to the law of your country.
Please Don’t try to fix this unit or change any parts inside (unless it ‘s shown the specific instruction guiding you t o do so). Please contact your wholesaler or distributor when the system needs to be repaired.

Replacement Policy

A.Exchange Policy:
A) Within a month from the customer buy the system, if there’ s rot artificial damage and under the proper using, and there’s no any scars of the system, the customer can change the new one from the distri butor.
B) Please show the receipt and Warranty card to the distributor when you’ re going to change the system, otherwise, the distributor can refuse to it.
B.Warranty Policy
Within a year from the customer buy the system, customer get Free Maintenance Service. For the products bought over a year or some Force majeure factor or artificial damage, we can offer Paid maintenance service.