REVOX C18 Multiuser Wall Control Instructions

June 15, 2024
REVOX

REVOX C18 Multiuser Wall

REVOX-C18-Multiuser-Wall-product

Product Information

The C18 Multiuser Wall Control is a user-friendly device that allows users to control various functions of their audio system. It features multiple user favorites, code pages, and remote control capabilities.

Specifications

  • Protection rating: IEC 60529
  • Operating temperature: Suitable for various environments
  • Power consumption: Dependent on usage
  • Parallel operation: Supports up to 2 wall controls

Product Usage Instructions

User Favorites

To access user favorites, follow these steps:

  1. Short press: Displays the last favorite of User 1 or User
  2. Long press: Displays the first favorite of User 1 or Use2

Code Pages

The C18 Multiuser Wall Control supports multiple code pages. To switch between code pages, use the following commands:

  • [17] [63] [24] [63] [25] [63] [26] [63]
  • [20] [63] [24] [55] [25] [55] [26] [55] [07] [63] [24] [56] [25] [56] [26] [56]
  • [21] [63] [24] [57] [25] [57] [26] [57]
  • [19] [63] [24] [51] [25] [51] [26] [51]

Remote Control Commands

The C18 Multiuser Wall Control can send various remote control commands. Use the following commands for specific functions:

  • Track Down: [**] [33] [24] [19] [25] [19] [26] [19]
  • Track Up: [**] [32] [24] [18] [25] [18] [26] [18]
  • Volume Down: [**] [17] [24] [21] [25] [21] [26] [21]
  • Volume Up: [**] [16] [24] [20] [25] [20] [26] [20]
  • Power Off: Short press to turn off the room, long press to turn off the entire system

Control RC 5 Commands

The C18 Multiuser Wall Control can be used to control RC 5 commands. Use the DIL switches and LED settings to configure the desired behavior.

Parallel Operation

The C18 Multiuser Wall Control supports parallel operation. You can connect up to 2 wall controls in parallel for convenient access.

Contact Information

If you have any questions or need further assistance, please contact Revox Deutschland GmbH using the following details:

Address: Am Krebsgraben 15, D-78048 VS-Villingen

Phone: +49 7721 8704 0

Email: [email protected]

Website: www.revox.com

Frequently Asked Questions (FAQ)

Q: How many wall controls can be connected in parallel?

A: The C18 Multiuser Wall Control supports parallel operation and can be connected with up to 2 wall controls.

Q: Can I control different code pages with this device?

A: Yes, the C18 Multiuser Wall Control allows you to switch between different code pages using the specified commands.

Q: What should I do if I need assistance or have questions?

A: If you need further assistance or have any questions, please contact Revox Deutschland GmbH using the provided contact information.

C18 Multiuser Wall Control

  • With the C18 Multiuser Wall Control, commands (IR triggers) can be sent to the multiuser system, which are stored in the multiuser server. The function is defined in the configurator itself. In addition, different behavior can be defined between a short and long key press.
  • Using the integrated IR receiver (left of the power button), infrared codes (RC5) can be received from IR remote controls and forwarded to the multiuser system for IR triggers.
  • Using the DIL switches on the back of the wall keyboard, different RC5 addresses can be selected in case there are IR conflicts with other remote controls/devices.

Command overview code

REVOX-C18-Multiuser-Wall-Control-fug-3

Code page option for C18 wall keyboard available from SW version 1.00
** RC5 code is combined with the current user/source address, i.e. if user 2 (address 21) was last selected, for example the volume_up command is also given address 21 and an RC5 command [21] [16] is sent.

Control RC 5 commands

The multiuser amplifier M30 or V219 offers control over the set RC5 code in its display. With its setup button, the infrared mode can be selected, which detects received signals from the IR link input and displays its RC5 address and command:

IR display multiuser amplifier M30 or V219

DIL switch
With the introduction of SW version 218-2 1.00 (Multiuser Programmer Software) there is a code page option for the C18 Multiuser Wall Control. 4 different code pages can be selected using DIL switches 3 and 4 on the back of the C18 wall keyboard. To do this, remove the wall control and remove the plastic cover the back. The desired code page can now be set with a small screwdriver. When the cover is open, please observe the common ESE regulations in order not to damage the electronics.

RC5 Codes C18 Multiuser Wall Remote

DIL Function Description Factory setting
1 IR Auge Internal infrared receiver on [1]/off [0]
A  

2| LED| LED on [1]/off [0]| A
3 + 4| RC5-Code Pages| RC5 address combinations 00: Code Page 1

01: Code Page 2

10 : Code Page 3

11: Code Page 4

| Off + Off [00]

cabling
The C18 wall control is connected to the multiuser amplifier via a 3-pin screw connector. When wiring, make sure that with a CAT cable (S/FTP, F/FTP) the shielding is connected to the GND line on both sides. In addition, a pair of wires should be connected together for a signal. Both measures increase the cable cross-section and thus reduce the voltage drop in the cable. With this cabling variant, cable lengths of up to 100 m can be achieved. Alternatively, a data cable of type U72 (1x4x0.5 mm2) can also be used.

REVOX-C18-Multiuser-Wall-Control-fug-4

Parallel connection

For larger rooms, it may make sense to place two C18 wall keyboards in different places in the room. 2 C18s can be operated in parallel, i.e. all 3 signal lines (GND, IR, VCC) are connected in parallel.
To avoid double commands when using remote controls if both wall keyboards could receive the IR signal, it is recommended to deactivate the IR receiver on one of the two C18 wall controls. This is set via a DIL switch (DIL 1) on the back of the wall keyboard – see illustration above.
The IR link, including the trigger out of the multiuser amplifier, may be loaded with a maximum of 80 mA. The nominal current requirement of a C18 at 23 mA.

Technical data

  • Protection class according to IEC 60529 Ambient temperature
    IP20, dry installation

    • Operation: -5 °C to +45 °C
    • Storage: -25 °C to +70 °C
    • Connection type Screw connector 3 x 0.15 – 1.50 mm² DIL switch
  • Factory setting:

    • 1: IR on
    • 2: LED on
    • 3: Code Page 0 (Code page 1)
    • 4: Code Page 0 (Code page 1)
  • Cable

    • Installation cable S/FTP or F/FTP or
    • Installation cable U72 ABG 1 x 4 x 0.5 mm² shielded
  • Maximum cable lengths to Revox Multiuser amplifier V219: max. 100 m

  • Current consumption 17 mA (passive) / 23 mA (button pressed) Parallel

  • operation max. 2 wall controls in parallel Revox

Revox Deutschland GmbH | Am Krebsgraben 15 | D-78048 VS-Villingen | Tel.: +49 7721 8704 0 | [email protected] | www.revox.com

© Copyright 2023 – Revox Group. All Rights Reserved

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

REVOX User Manuals

Related Manuals