K-ARRAY KAMUT2V25 Minimalist Design Maximum Connectivity User Guide

: June 16, 2024
: K-ARRAY

K-ARRAY KAMUT2V25 Minimalist Design Maximum Connectivity

Technical Specifications

Model: Azimut-KAMUT2L1, Azimut-KAMUT2L14, Azimut-KAMUT2V25, Azimut-KAMUT2L
Design: Minimalist
Connectivity: Maximum

Product Usage Instructions

Unpacking
Each K-array amplifier is built to the highest standard and thoroughly inspected before leaving the factory. Upon arrival, carefully inspect the shipping carton, then examine and test your
new amplifier. If you find any damage, immediately notify the shipping company.

Check that the following parts are supplied with the product:

Azimut-KAMUT2L1:
- 1x Kommander-KA02 amplifier
- 1x Truffle-KTR24 subwoofer
- 2x Lyzard-KZ1 ultra miniaturized loudspeaker w/cable
- 1x Remote
- 1x Subwoofer cable
- 1x Power supply w/power cord
- 2x Line input connectors (Phoenix MC 1.5/3-G-3.81)
Azimut-KAMUT2L14:
- 1x Kommander-KA02 amplifier
- 1x Truffle-KTR25 subwoofer
- 2x Lyzard-KZ14 ultra miniaturized line-array element w/cable
- 1x Remote
- 1x Subwoofer cable
- 1x Power supply w/power cord
- 2x Line input connectors (Phoenix MC 1.5/3-G-3.81)
Azimut-KAMUT2V25:
- 1x Kommander-KA02 amplifier
- 1x Truffle-KTR24 subwoofer
- 2x Lyzard-KZ1 ultra miniaturized loudspeaker w/cable
- 1x Remote
- 1x Subwoofer cable
- 1x Power supply w/power cord
- 2x Line input connectors (Phoenix MC 1.5/3-G-3.81)
Azimut-KAMUT2L:
- 1x Kommander-KA02 amplifier
- 1x Truffle-KTR25 subwoofer
- 2x Lyzard-KZ1 ultra miniaturized loudspeaker w/cable
- 1x Remote
- 1x Subwoofer cable
- 1x Power supply w/power cord
- 2x Line input connectors (Phoenix MC 1.5/3-G-3.81)

Hardware Configuration
The hardware configuration may vary based on the specific model. Please refer to the user manual for detailed instructions on hardware configuration for each model.

Loudspeaker Wirings
The loudspeaker wirings may vary based on the specific model. Please refer to the user manual for detailed instructions on loudspeaker wirings for each model.

Setup Installation
The setup installation process may vary based on the specific model. Please refer to the user manual for detailed instructions on the setup installation process for each model.

The setup installation may include:

Adhesive strips and Dual Lock pads
Permanent installation with wall plug
Subwoofer setup

Wireless Remote
The product comes with a wireless remote control for convenient operation. Please refer to the user manual for detailed instructions on how to use the wireless remote control.

Wired Remote
The product also supports a wired remote control option. Please refer to the user manual for detailed instructions on how to use the wired remote control.

Azimut Discovery App
The Azimut Discovery app allows you to control and configure your Azimut product. Please refer to the user manual for detailed instructions on how to use the Azimut Discovery app.

Bluetooth Pairing
To pair your device with Bluetooth, follow these steps:

Open the Bluetooth settings on your device.
Put your Azimut product into pairing mode (refer to the user manual for instructions).
Select your Azimut product from the list of available devices on your device’s Bluetooth settings.
Once connected, you can play audio from your device through your Azimut product.

Reset Network Parameters
If you need to reset the network parameters of your Azimut product, follow the instructions provided in the user manual.

Azimut Control Interface
The Azimut Control Interface allows you to access various settings and features of your Azimut product. Please refer to the user manual for detailed instructions on how to use the Azimut
Control Interface.

Main Menu
The main menu of the Azimut Control Interface provides access to different sections and settings. Please refer to the user manual for detailed instructions on how to navigate and use the main menu.

Network & Bluetooth
The Network & Bluetooth section of the Azimut Control Interface allows you to configure network and Bluetooth settings. Please refer to the user manual for detailed instructions on how to configure network and Bluetooth settings.

Local Streaming
The Local Streaming section of the Azimut Control Interface allows you to stream audio from local sources. Please refer to the user manual for detailed instructions on how to use local
streaming.

Advanced Settings
The Advanced Settings section of the Azimut Control Interface provides access to advanced configuration options. Please refer to the user manual for detailed instructions on how to configure advanced settings.

System Update
If a system update is available for your Azimut product, you can update it using the provided instructions in the user manual.

Update via USB
If an update via USB is available for your Azimut product, you can update it using the provided instructions in the user manual.

Hardware Control Setup
The hardware control setup may vary based on the specific model. Please refer to the user manual for detailed instructions on how to set up hardware controls for each model.

Output Configuration
The output configuration may vary based on the specific model. Please refer to the user manual for detailed instructions on how to configure the output for each model.

Routing
The routing options may vary based on the specific model. Please refer to the user manual for detailed instructions on how to configure the routing for each model.

Azimut Remote App
The Azimut Remote App allows you to control and configure your Azimut product from your mobile device. Please refer to the user manual for detailed instructions on how to use the Azimut Remote App.

FAQ

Q: Where can I find the user manual?
A: The user manual can be found at https://manual-hub.com/
Q: How can I contact customer service?
A: For any questions or support, please contact K-array customer service at support@k-array.com or contact the official K-array distributor in your country.
Q: How can I listen to Spotify using Azimut-KA02?
A: To listen to Spotify using Azimut-KA02, follow these steps:
Connect your Azimut-KA02 to your local network.
Open up the Spotify app on your phone, tablet, or laptop using the same network.
Play a song and select Devices Available.
Select your Azimut-KA02 and start listening.

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions – Keep these instructions Heed all warnings

Warning. Failure to follow these safety instructions could result in fire, shock or other injury or damage to the device or other property.

Installation and commissioning may only be carried out by qualified and authorized personnel.

Switch-off the mains power supply before carrying out any connection or maintenance operations.

Symbols

K-array declares that this device is in compliance with applicable CE standards and regulations. Before putting the device into operation, please observe the respective country-specific regulations!
WEEE
Please dispose of this product at the end of its operational lifetime by bringing it to your local collection point or recycling center for such equipment.
This symbol alerts the user to the presence of recommendations about the product’s use and maintenance.
The lighting flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated, dangerous voltage within the product enclosure that may be of magnitude to constitute a risk of electrical shock.
This device complies with Restriction of Hazardous Substances Directive.

General heed and warnings

Read these instructions.
Keep this instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
This loudspeaker system is intended for professional use.
Beware of sound levels. Do not stay within close proximity of loudspeakers in operation. Loudspeaker systems are capable of producing very high sound pressure levels (SPL) which can instantaneously lead to permanent hearing damage. Hearing damage can also occur at moderate level with prolonged exposure to sound. Check the applicable laws and regulations relating to maximum sound levels and exposure times.
Before connecting the loudspeakers to other devices, turn off the power for all devices.
Before turning the power on or off for all devices, set all volume levels to minimum.
Use only speaker cables for connecting speakers to the speaker terminals.
Be sure to observe the amplifier’s rated load impedance particularly when connecting speakers in parallel. Connecting an impedance load outside the amplifier’s rated range can damage the devices.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
K-array will not shoulder any responsibilities for products modified without prior authorization.
K-array cannot be held responsible for damage caused by improper use of the loudspeakers.

Thank you for choosing this K-array product!
To ensure proper operation, please carefully read this owner’s manual and safety instruction before using the product. After reading this manual, be sure to keep it for future reference.
Should you have any questions about your new device please contact K-array customer service at support@k-array.com or contact the official K-array distributor in your country.

Your new speaker has Spotify Connect built in. You need a Spotify account to take advantage of Spotify Connect.
Spotify Connect lets you control the music playing on your device, using the Spotify app on your mobile, tablet or PC. Listening is seamless. You can take calls, play games, even switch your phone off – all without interrupting the music. Learn more at spotify.com/connect
The Spotify software is subject to third party licenses found here: www.spotify.com/connect/third-party-licenses

Listen out loud with Spotify Connect

Connect your Azimut-KA02 to your local network;
Open up the Spotify app on your phone, tablet or laptop using the same network;
Play a song and select Devices Available;
Select your Azimut-KA02 and start listening.
- A. Lyzard-KZ1
- B. Lyzard-KZ14
- C. Vyper-KV25
- D. Truffle-KTR24
- E. Truffle-KTR25
- F. Truffle-KTR26
- G. Rumble-KU44-2
- H. Kommander-KA02

Unpacking

Each K-array amplifier is built to the highest standard and thoroughly inspected before leaving the factory. Upon arrival, carefully inspect the shipping carton, then examine and test your new amplifier. If you find any damage, immediately notify the shipping company. Check that the following parts are supplied with the product.

Azimut-KAMUT2L1

1x Kommander-KA02 amplifier
1x Truffle-KTR24 subwoofer
2x Lyzard-KZ1 ultra miniaturized loudspeaker w/cable
1x Remote
1x Subwoofer cable
1x Power supply w/power cord
2x Line input connectors
(Phoenix MC 1.5/3-G-3.81)
3x Adhesive magnetic strip
3x Double-sided removable adhesive strip

Azimut-KAMUT2V25

1x Kommander-KA02 amplifier
1x Truffle-KTR26 subwoofer
2x Vyper-KV25 line-array element 1x Remote
1x Subwoofer cable
2x Loudspeaker cables
1x Power supply w/power cord
2x Line input connectors
(Phoenix MC 1.5/3-G-3.81)
4x Pairs of 3M Dual Lock pads
4x Wall mount brackets

Azimut-KAMUT2L14

1x Kommander-KA02 amplifier
1x Truffle-KTR25 subwoofer
2x Lyzard-KZ14 ultra miniaturized line-array element w/cable
1x Remote
1x Subwoofer cable
1x Power supply w/power cord
2x Line input connectors
(Phoenix MC 1.5/3-G-3.81)
3x Adhesive magnetic strip
3x Double-sided removable adhesive strip

Azimut-KAMUT2L

1x Kommander-KA02 amplifier
1x Rumble-KU44-2 subwoofer
2x Lyzard-KZ14 ultra miniaturized line-array element w/cable
1x Remotee
1x Subwoofer cable
1x Power supply w/power cord
2x Line input connectors (Phoenix MC 1.5/3-G-3.81)
3x Adhesive magnetic strip
3x Double-sided removable adhesive strip

Subwoofer cable
Vyper-KV25 cable*
Brackets for Vyper-KV25*
Balanced connection plugs
Wired loudspeaker plugs
Ethernet Port
USB ports
Optical input
3,5 mm jack analog input
Balanced analog inputs
Remote Control connector
Output connections
Wi-Fi reset switch
GPIO port
DC inlet
Power switch

Available for Azimut-KAMUT2V25 only.

Hardware Configuration

Azimut-KAMUT2L1

Azimut-KAMUT2L14

Azimut-KAMUT2V25

Azimut-KAMUT2L

Loudspeaker Wirings

Cables with proper terminal connectors are provided within the package: follow the hardware configuration section for setting the connections.

Lyzard wirings
Lyzard loudspeakers are already pre-wired with 5 m (16.4 ft) of ultra-thin speaker cable to be directly connected to the K-array Kommander-KA02 power amplifier.

Before connecting the loudspeaker cable to the amplifier:

insure the amplifier’s minimum loading impedance is matched, especially when connecting multiple loudspeakers in parallel (see next paragraph);
insure that the amplifier is switched off.
The Lyzard’s ultra-thin speaker cable should not be cut, jointed or soldered.

Instead of altering the wiring, replace the cable. In case of cable replacement, for a cable run of up to 5 m (16.4 ft) use wire gauge of 0,5 mm2 (24 AWG) at least. For longer cable runs a wider gauge is recommended. In order to screw the terminals of the Lyzard loudspeakers, use 2 mm (5/64 in) standard (flat-blade) screwdriver.

Setup

Lyzard and Vyper loudspeakers perform best when positioned on a planar surface such as a wall. Find the proper installation height, aiming the loudspeaker at the listening position.

We suggest the following configurations:

Sitting people
H: min height 1,5 m (5 ft) / max height 2,5 m (8¼ D: min distance: 2,5 m (8¼ ft)

Standing people
H: min height 1,7 m (5⅔ ft) / max height 2,7 m (9 ft) D: min distance: 2,5 m (8¼ ft)

TV screens or displays

Installation

Adhesive strips and Dual Lock pads The adhesive strips and Dual Lock pads are intended for quick and clean installation on flat surfaces, being ready to use for either fixed and temporary installations.

Permanent installation, wall plug
For permanent installation a kit including a proper screw and plug is provided.

Follow these operating instructions:

Before permanently affixing the loudspeaker to the surface, gently remove the outer grill;
Drill a 4 mm (0.15 in) diameter hole in the surface with a deep of at least 20 mm (0.80 in);
Set the wall plug in place and gently screw the loudspeaker to the surface;
Reposition the outer grill on the loudspeaker.

Subwoofer
Truffle subwoofer are designed to be easy to conceal on top or bottom of the furnitures. Insure to leave enough free space all around the subwoofer in order to let the sound propagate properly.

Wireless Remote

The wireless remote provides complete control over the Azimut playback features. The remote includes a high efficiency rechargeable battery: a switch allows to power off the remote in order to extend the battery life. When the battery discharges to approximately 10% remaining life, the LED on the remote starts flashing: connect the remote’s charge port to a standard USB port to recharge the internal battery; use the provided cable.

| Command| Battery low
---|---|---
received| not received
Status LED| single blink| long blinking| flashing

Bluetooth pairing
Press the bluetooth button to set the Azimut to Bluetooth pairing mode

Wired Remote

| Standby| Power On
---|---|---
Status LED| Pulse Blinking| Solid White

Bluetooth pairing
Keep pressed for 10 seconds the bluetooth button to set the Azimut to Bluetooth pairing mode The Azimut system can be completely controlled by any mobile device or desktop PC via the Azimut Control Interface. We strongly suggest to implement the Azimut system within your network environment and then access its features relying on your wireless access point or wired devices. Bluetooth Connectivity is dedicated to direct streaming from any mobile device supporting the Bluetooth 4.1 protocol.

Remote Connectivity
Name and password for accessing the Azimut Control Interface are collected on a label underneath the Kommander-KA02 amplifier.

Default IP: 192.168.10.1
Default password: 12345678

Azimut Discovery app

Download the Azimut Discovery App for your device:

Connect the Azimut to your Wi-Fi access point via a dedicated Ethernet cable.

Use the Azimut Discovery app to discover and direct access the Azimut Control Interface within your Wi-Fi network.

Bluetooth pairing
Set the system waiting for pairing with your bluetooth device either pressing the dedicated button on the remote, or using the Azimut Control Interface Bluetooth pairing can be achieved by the Network & Bluetooth section in the A as well. See the Network & Bluetooth for more details.

Reset Network Parameters
With the system on, keep pressed for 10 seconds the network reset button on the rear panel to revert the network parameters to the default factory settings. The network addressing mode reverts to DHCP and the default Wi-Fi IP address and password are restored.

Azimut Control Interface

Main menu

Remote control
The default view with Audio sources and Players selections.

Audio Setup
User equalizer and level tuning.

Local Streaming
Manage a group of devices by a single Azimut system.

Network & Bluetooth
Modify network and Bluetooth settings.

Advanced
Set advanced features.

Network & Bluetooth

Local streaming

This feature allows to manage a group of Kommander-KA02 Azimut amplifiers by a single Azimut system.

Preliminary setup:

Connect all the Kommander-KA02 to the same network;
Set a unique name on each device in order to ease its detection and setup (see Advanced section for details);
Select one Azimut system as Master device on the network: this device will stream its music to any other Azimut system marked as Slave.

Local streaming setup:

Connect to one Azimut system and access its Azimut Control Interface;
Browse the Main menu and click on Local streaming: the view will show the complete list of the Azimut systems within the network of the Azimut you are connected to;
For each listed Azimut system you can:
- set it as Master: this device will stream the music to any other Slave Azimut system in the network.
  WARNING: only one Master device is allowed within the network
- set it as Slave: this device will playback the music streamed by the Master;
- toggle the standby mode in order to wake up or turn off the system (resume or stop playback accordingly);
- set the playback volume.

By accessing the Azimut Control Interface of an Azimut system within the network it is possible to override the Local streaming setting and free the device.

Advanced settings

SYSTEM UPDATE
The Kommander-KA02 Azimut amplifier can be easily updated in the Advanced settings view.

Connect to the Azimut system and access its Azimut Control Interface;
Browse the Main menu and click on Advanced;
Expand the Version Info section: if the Azimut system is connected to Internet, the system will look for updates on K-array website. When a new firmware version is available, the Download button lights on.
Click on the Download button and wait for the firmware update file to be saved on-board.
When the Install button lights on: click on the Install button to start the system update.

Do not reboot the system until the alert message appears. During firmware update, please don’t modify any parameter of the device on the web interface.

UPDATE VIA USB

Download the firmware packages form the Azimut support webpage in www.k-array.com;
Format the USB memory stick with FAT16 or FAT32 file system;
Create a folder named “update” (case sensitive) in the root of the USB memory stick;
Copy the firmware packages marked as “update” into the update folder: files must follow the correct naming pattern, and both .package and .package.sha256 files must be present into the folder:
|-update\
|-rootfs-update-1.0.5.0.package
|-rootfs-update-1.0.5.0.package.sha256
Connect the USB memory to the Azimut;
Connect to the Azimut system and access its Azimut Control Interface;
Browse the Main menu and click on Advanced;
Expand the Version Info section;
Click on the Install via USB button.

Hardware control setup

The Kommander-KA02 Azimut amplifier provides a General Purpose Input connector designed to connect up to four external normally open (NO) switches* to be set as a further remote user customizable controls.

In order to bind the remote control to an Azimut operating functionality (actions) follow these step:

Connect the external NO switch to the ground (GND) terminal and to one of the four available terminals of the flying plug;
Plug the flying plug to the Hardware Control port on the Kommander-KA02 back panel;
Open the Azimut user interface, click on the Main Menu icon and select Advanced;
Scroll down and find the Hardware Control section;
Find the control with the number corresponding to the hardware control terminal where you plugged the remote switch and set the proper action;
Enable the remote control;
Click on Save setup to make the settings effective.

external normally open (NO) switches are not provided with the Azimut system.

Actions

mute/unmute
set volume (max: +12, min: -90)
Increase volume
Decrease volume
play/pause
play/pause Spotify

Output configuration
This view allows to modify the loudspeaker assignment to the Kommander-KA02 amplifier output channels. These configuration shall be set by authorized operators.
WARNING: wrong loudspeaker selection may seriously damage connected loudspeakers.

Routing
This view allows to modify the LEFT and RIGHT input channel assignment to the Kommander-KA02 amplifier output channels.

Azimut Remote App

Azimut Remote is a iOS application that allows the user to remotely control a single Kommander-KA02 amplifier unit via an Ethernet connection.

Azimut Remote offers an easy to use interface for managing audio playback and Bluetooth pairing, as well as four fully user programmable buttons.

In order to connect the Azimut Remote to the Azimut system:

Be sure that the Azimut systemn and your iOS device are connected to the same network.
Launch the Azimut Discovery application (see Azimut Remote App, p. 16). The app will show the discovered Azimut Systems on the network: make note of the IP address of the device you want to control with the Azimut Remote app.
Launch the Azimut Remote app and open the Settings view.
Insert the IP address of the device you want to control in the General field on top of the page.
Click on Back: the app is now linked to your Azimut System

In order to customize the action associated to the four programmable buttons:

Select the button you want to program and set the proper action among the one listed in the table below.
Some actions require you to define the argument of the setting (e.g. the volume) in the PUT Data field. If not required, leave this field empty.
Enable the button to make it active.

You can eventually control a different device within the network setting preceding the action string with the IP address of the target device; e.g. pause playback of the device with IP 192.168.10.100: http://192.168.10.100/api/v1/player/pause

Technical Specifications

| Lyzard-KZ1| Lyzard-KZ14| Vyper-KV25
---|---|---|---
Type| Point source| Line array| Line array
Rated Power| 3.5 W| 15 W| 75 W
Frequency Response| 500 Hz – 18 kHz (-6 dB) 1| 500 Hz – 18 kHz (-6 dB) 1| 150 Hz – 18 kHz (-6 dB) 1
Maximum SPL| 86 dB (peak) 2| 98 dB (peak) 3| 108 dB (peak) 3
Coverage| V. 140° | H. 140°| V. 40° | H. 140°| V. 25° | H. 120°
Transducers| 0,5” neodymium magnet woofer| 4x 0,5” neodymium magnet woofers| 4x 1” neodymium magnet woofers
Colors| Black, white, custom RAL
Finishes| Polished stainless steel, 24K gold finishes| Brushed and polished stainless steel, 24K gold finishes
Material| Aluminum
Dimensions (WxHxD)| 22 x 37 x 11 mm
(0.9 x 1.5 x 0.4 in)| 22 x 100 x 11 mm
(0.9 x 3.9 x 0.4 in)| 40 x 260 x 22 mm
(1.6 x 10.2 x 0.9 in)
Weight| 0.021 kg (0.046 lb)| 0,059 kg (0.130 lb)| 0,4 kg (0.88 lb)
IP Rating| IP64
Impedance| 16 Ω| 16 Ω| 8 Ω / 32 Ω selectable

With dedicated preset.
Maximum SPL is calculated using a signall with crest factor 4 (12dB) measured at 1 m.
Maximum SPL is calculated using a signall with crest factor 4 (12dB) measured at 8 m then scaled at 1 m.

| Truffle-KTR24| Truffle-KTR25| Truffle-KTR26| Rumble-KU44-2
---|---|---|---|---
Type| Point source| Point source| Point source| Point source
Rated Power| 60 W| 80 W| 100 W| 120 W
Frequency Response| 45 Hz – 150 Hz (-6 dB) 1| 45 Hz – 150 Hz (-6 dB) 1| 45 Hz – 150 Hz (-6 dB) 1| 50 Hz – 150 Hz (-6 dB) 1
Maximum SPL| 112 dB (peak) 2| 115 dB (peak) 2| 120 dB (peak) 2| 116 dB (peak) 2
Coverage| Omni| Omni| Omni| Omni
Transducers| 4″ woofer + passive radiator| 5.25″ woofer + passive radiator| 6.5″ woofer + passive radiator| 2 x 4” neodymium magnet
2 x 4” passive transducer
Colors| Black| Black, white, Custom RAL
Finishes| Powder Matte| Gold, Polished, Brushed
Material| Aluminum| Stainless Steel
Dimensions (WxHxD)| 122 x 117 x 199 mm (4.8 x 4.6 x 7.8 in)| 152 x 147 x 258 mm (6.0 x 5.8 x 10.2 in)| 182 x 176 x 341 mm (7.1 x 6.9 x 13.4 in)| 500 x 116 x 100 mm 3 (19.7 x 4.6 x 4.0 in)
Weight| 1,5 kg (3.31 lb)| 2,5 kg (5.51 lb)| 3,5 kg (7.72 lb)| 5,9 kg (13.0 lb)
IP Rating| IP64| IP64
Impedance| 4 Ω| 4 Ω| 2 Ω| 2 Ω

With dedicated preset.
Maximum SPL is calculated using a signall with crest factor 4 (12dB) measured at 1 m.
Removable rubber feet not included.

| Kommander-KA02
---|---
Type| 4-channel Class D audio amplifier
Rated Power| 4x 50W @ 4Ω
Frequency Response| 20 Hz – 20 kHz (±1 dB)
Connectivity| Bluetooth 4.1 Low Energy, Wi-Fi, Ethernet| 2x Phoenix Connectors (bal)
3.5 mm Jack Stereo (unbal) Toslink Optical Connector
Control| Dedicated Azimut Control Interface / wired Remote Control
Operating range| Dedicated AC/DC power adapter 100-240V ~ AC, 50-60 Hz input / 24 V, 4 A DC output
Colors and Finishes| Black / Powder Matte
Material| Aluminum
Dimensions (WxHxD)| 144 x 46 x 144 mm (5.6 x 1.8 x 5.6 in)
Weight| 0,5 kg (11 lb)
Load impedance| minimum 4 Ω

Designed and Made in Italy
K-ARRAY surl
Via P. Romagnoli 17 | 50038 Scarperia e San Piero – Firenze – Italy ph +39 055 84 87 222