SafeGuard RF3.1 and RF4.1 Cordless Sensor Light Instruction Manual
- June 4, 2024
- SAFEGUARD
Table of Contents
Instruction Manual RF3.1 and RF4.1
RF3.1 and RF4.1 Cordless Sensor Light
|
---|---
Intended Use of Product
Please read the full instructions before operating the product. This product is to be used as a cordless motion sensor safety light as directed by the instructions.
Specification
| Operating voltage | 4.5 V | 4.5 V |
|---|---|---|
| Maximum wattage | 3 W | 6 W |
| Batteries | 3 x C | 3 x C |
| Lumens | 130 Im | 260 Im |
| Operating temperature | -20°C to +50°C | -20°C to +50°C |
| IP rating | IP 55 | IP 55 |
| Sensor | Automatic motion & Photo sensor detection | Automatic motion & Photo |
sensor detection
Sensor detection range| 8 meters & 110 degrees| 8 meters & 110 degrees
Light modes| On / Off / Auto| On / Off / Auto
Detection time| Auto mode: 10 seconds| Auto mode: 10 seconds
Product Features
- Cordless safety and security LED sensor light
- Battery operated
- Quick release button for easy battery replacement
- Simple and quick to install
- Horizontal and vertical light adjustment
- Multi-mounting options
- Adjustable sensor angle
- For use indoors and outdoors
Package Includes
- GP SafeGuard cordless sensor light
- 3 x GP14AU 1.5V Ultra Alkaline battery
- Accessories for installation L-bar, end clamp, sensor masks, screws, raw plugs, L-bar cap and wing nut
Product Installation
2.1 Method 1: Permanent installation
2.1 a Push the lock button to the “OPEN” position on the SafeGuard.
2.1 b Detach the wall mounting plate from the base of the SafeGuard.
2.1 c Use the wall mounting plate as a template and mark the location for the
screws.
2.1d Drill holes and insert the raw plugs (if necessary). Attach the wall
mounting plate with the screws.
2.1e Reattach the SafeGuard on the mounting plate.
2.1f Push the lock button to the “CLOSE” position.
2.2 Method 2: Removable installation when Method 1 is not feasible
2.2a Insert the L-bar in the SafeGuard base.
2.2b Place the SafeGuard on a beam or similar object.
2.2c Insert the end clamp through the L-bar and tighten the wing nut to secure
the SafeGuard.
2.2d Push L-bar cap on the end of the L-bar.
2.2e The beam thickness must be a minimum of 4.5cm.
Battery Installation
4 Angle Adjustments
5 Operating Instructions
5a Light Modes
ON: SafeGuard turned on permanently
OFF: SafeGuard turned off
AUTO: SafeGuard activates when movement is detected from dusk till dawn.
Switches on for approx. 10 seconds unless it continues to detect movement
5b Sensor Detection Area
can be reduced by covering the sensor with a sensor mask.
Light Sensitivity
The built-in dusk to dawn sensor can be set to suit your preference. By
turning it to the Moon icon the light will operate in the darker environment
or it can be set to the Sun icon which results in operating more in lit-up
areas or during the day. It can be also adjusted anywhere between these two
points.
Attention
- PIR sensors detect changes in infrared light (heat) therefore the surrounding temperature can affect the sensor’s responsiveness.
- Placing the SafeGuard too close to strong ambient light may affect the sensor’s response.
- The SafeGuard is most sensitive when people cross its sensor’s detection area.
Safety Instructions
Keep products in safe locations away from children. Do not swallow small parts. This product is not suitable for children and the instructions should be followed carefully to avoid Injury.
- Do not use in explosive atmospheres or other areas where there may be volatile gases.
- Do not immerse, incinerate or disassemble the product.
- Do not short circuit the product In any way.
Maintenance and Repair
- Do not attempt to modify or repair the product. All repairs must be carried out by authorized personnel.
- Use the correct batteries for the product. Never use alkaline / non-rechargeable batteries and rechargeable batteries together.
- Store batteries out of the reach of children.
- Never expose batteries to temperatures over 60’C (e.g. direct sunlight or to open fire).
- Do not short-circuit batteries.
- Do not use new batteries with partially used or discharged batteries.
- If the product Is not being used for an extended period of time please remove the batteries from the device.
- Dispose of batteries according to national guidelines.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>