tuya TY130 Fingerprint Smart Door Lock Instruction Manual

tuya TY130 Fingerprint Smart Door Lock

Packing List

Open the product package. Check that the following accessories are included.

Installation Steps

STEP 1
Pass the square along the wire.

STEP 2
Choose the screw of the corresponding length according to the thickness of the door and tighten the screws.

STEP 3
Open the battery cover to install the battery

STEP 4
Install the deadbolt

Attention

Open to inside

1. Pay attention to the direction of the lock tongue when you installing
2. The hole position can be adjusted according to the door lock position

OUTSIDE INSIDE

1. Install and fix the door handle.
2. Connect the door lock circuit board port.
3. Tighten the screws securing the battery cover.
4. After completing the above steps, the door lock installation is com- plate.

Indoor Smart Lock Operation Guide

Part I: Operation instructions for the smart lock The first three fingerprint users registered are administrators after the initialization of the smart lock, all other registered users are common users. If an administrator has been registered in the smart lock, you have to verify the administrator before adding or deleting users. When the smart lock is not registered with any users, every fingerprint can open the lock. Unregistered fingerprints can’t open the lock once there is one user is registered.

Unlocking

• Verification success – green light
• Verification failure → red light

Lock
Auto-lock in 5 seconds after unlocking Add fingerprints (the first 3 registered users are administrators by default, all other users are common users): Press the setting button around 1s → blue light blinks – verify the administrator (no administrator, any fingerprint) → blue light is always on → press the new fingerprint you want to enter 5 times, the successful entry flashing green light, failure flashing red light, exit the setting automatically once the setting is completed;

Resetting

Long press the setting button for & seconds – the blue light flashes, the red light flashes after 8 seconds and a green light appears to indicate successful resetting. All registered fingerprints will be deleted and the smart lock will be automatically removed from the App at the same time;

Free Passage Mode
Turn on Free Passage Mode Press the Free Passage button for 1 second – the pink light flashes, and the green light is on shortly which indicates the Free Passage mode is turned on; Turn off Free Passage Mode
Option 1: Press the Free Passage button for 1 second → the pink light flashes, and the blue light is on shortly which indicates that the Free Passage mode is turned off;
Option 2. Verify the registered fingerprint, the system defaults to turn off the free passage mode;

Part II: Operation Instructions of the App

Introduction of App

The “Tuya Smart” App is a smart device management App provided by Tuya to end- users. You can conveniently configure and control your purchased smart home products, configure your favourite scenes and automation solutions, share your smart devices with your family and friends, and enjoy the fun of whole-house intelligence. You can share your smart devices with your family and friends, and enjoy the fun of whole-house intelligence. Download App: Search “Tuya Smart” in the mobile application market or “Apple Store” or scan the following QR code to download it. This document takes the Tuya Smart App as an example to explain the functions of the APP in detail.

APP registration and login

****APP registration: If you don’t have an APP account, you can choose to register an account or log in via SMS verification code. Click “Create New Account”, and you will enter the account registration page. Follow the instructions to get the SMS verification code and set the password. If you already have an account, you can click “Sign in with existing account” to sign in APP, and the login method supports password, verification code and social account.

Add Bluetooth Smart Lock (Bluetooth of cell phones must be turned on)

1. Click the “Add Device” icon on the home page of APP.
2. Touch the reading area of fingerprints to wake up the smart lock, wait for the App to discover the device press “Add”, and press the “+” icon to add the device.
3. Wait for the device to be added. If the App goes to the home page of the smart lock, this indicates the smart lock has been added to the App successfully.

The Homepage of Bluetooth Smart Lock

1. There are, “Member Management”, “Unlock Record”, “Smart Scene”, and “Settings” at the bottom of the homepage. The name of the device and the battery are displayed on the Top of the homepage.
2. The Bluetooth connection status is displayed at the centre of the homepage. If the device is connected, you can long-press it to unlock the device.
3. Please make sure that the Bluetooth of the phone is turned on, the App has access to the Bluetooth, and the distance between the phone and the smart lock is within 5 meters.
4. If the Bluetooth is t connected, it will show “Can’t connect the Bluetooth”, you can not unlock the smart lock through the APP.

Fingerprint Management

1. Tap the “Setting” at the bottom of the home page, tap “Fingerprint management” and tap
2. Add Fingerprint” and select the user for this fingerprint.
3. Tap “Start Capturing”, the blue light stays on, place your fingerprint in the reading area and leave it until the green light turns on.
4. The light changes to a blue color, place your fingerprint on the reading area again and leave it until the green light turns on, do this 5 times total until the blue light turns off, which means the fingerprint is added.
5. You can add fingerprints for yourself or other users to add fingerprints on the App.
6. The light becomes green, which means the verification of Fingerprint is right. If the verification fails, the light thermos is red.

A Setting of Free Passage Mode and Anti-lock

Tap the
“Setting” at the bottom of the home page, you can turn on or off the Anti- lock. When the Anti-lock turns on, only the administrator (first 3 fingerprints registered) can unlock the door, other users cannot unlock the door. The Anti-lock will be turned off automatically once the administrator unlocks the door.

Tap the “Setting” at the bottom of the home page, you can turn on or off the”Free Passage Mode”. When the Free Passage mode is turned on, every fingerprint can unlock the door no matter whether this fingerprint is registered or not. The Free Passage Mode will be turned off automatically once the administrator unlocks the door. You can press the Free Passage Button around 1s to turn on or off the Free Passage Mode.
Note: The “Anti-lock” and “Free Passage Mode” can’t be turned on at the same time. The Free Passage Mode will be turned off automatically once the Anti-lock is turned on. When you turn on the Free Passage Mode, the Anti-lock will be turned off automatically.

Member Management – Family Member Management

1. Validity period: Once the family member is added, the family member always has permission to use the smart lock until the administrator removes the member.
2. Unlocking ways: the administrator can decide the type of permission the member can access; as shown in the figure, if the administrator disables all the unlocking permissions of the member, the member can’t add new unlocking permissions on the APP but the member still can use the registered unlocking permissions before the administrator disabling the member’s permission.
3. Adding or deleting the unlocking permission The administrator can add or delete the unlocking permissions for all family members on the App once the Bluetooth is connected.

Member Management – Other Member Management

1.  Validity period: The administrator can select permanent validity or select a limited period by date and time for the other members.
2. Unlock ways: the administrator can enable different types of permission for the other member to unlock the door. As shown in the figure, if the administrator disables all unlocking permissions of the other member, then the user can’t add new unlocking permissions on the APP but the member still can use the registered unlocking permissions before the administrator disabling the member’s permission.
3. After adding another member, the administrator has to tap the other member added and tap “Share” to input the account of the other member to grant access to this account. The shared device will be removed automatically from the APP of the user when the sharing expires.

Unlocking Records
You can check out the unlocking records on the App. When the door lock is connected to the App, the unlocking records will be displayed on the APP in real time, otherwise, the record will be only updated when the smart lock is connected to the App.

Resetting

1. Make sure the Bluetooth is connected and then reset the smart lock. Tap the “Edit” icon at the top right corner of the homepage, tap “Remove Device” and select “Disconnect and wipe data”. All unlocking permissions will be deleted.
   Note: If you reset the smart lock on the App when the Bluetooth is not connected, all registered unlocking permissions are still able to unlock the door and the smart lock can’t be added by other App. If the Bluetooth of the phone is turned on, the App will connect the smart lock automatically and then all unlocking permissions will be deleted right away and the smart lock can be added to the App again.

2. Long press the setting button for 8 seconds → The blue light flashes, the red light flashes after 8 seconds and a green light appears to indicate successful resetting. All registered fingerprints will be deleted and the smart lock will be automatically removed from the App at the same time.

Product technical parameters

Warm tip: Please keep your mechanical key outside of the home for use in case of emergency or malfunction!

Two Ways to Unlock

Fingerprint Unlock
Press the fingerprint sensor on the handle. If fingerprint verification succeeds, the indicator light will turn green and the lock.

Key Unlock – Emergency Unlock

Lock Automatically
The lock will automatically lock 3s later after unlocked.

Other Settings
Reset and Delete All the Users

STEP 1:
Long press the reset key on the inside handle with the pin for 9s, at the same time the indicator will blink blue.

STEP 2:
Till the indicator blinks red light, release the reset key and the indicator will turn green, which means resetting successfully.

Free Passage Mode
In Free Passage Mode, you can open the lock from outside without inputting your fingerprint.

Turn ON Free Passage Mode
Long press the Free Passage Mode switch button on the inside handle for 1s, while the indicator blinks pink light. Release the button and the indicator will turn green light then off, which means success.

Turn OFF Free Passage Mode
Do the same as 1) to exit Free Passage Mode

Emergency Unlock
Emergency Opening Method When the Battery is Powered Off

Plug the Type-C power
cord into the connector Press the registered admin- iterator fingerprint Unlocking is successful

Useful Tips

1. Keep at least one key out of the door for emergencies.
2. When the battery is low, the indicator will blink red light. The rest power could only be used for about 50 times.
3. When the battery is out of power, you can unlock the door with a key, or supply the lock with power through the Type-C port and use a fingerprint or password to unlock it.
4. Use alkaline batteries to prevent damage by battery leakage. Batteries must be replaced every 2 years.

Product Parameters

1. Number of fingerprints: 30
2. Power supply: 4 AAA alkaline batteries

After-Sales Service
If you have any problem during installation or operation, please contact us.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF waming for Portable device
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>