FIAMMA 98655-848 31 LED Awning Light Instruction Manual
- June 6, 2024
- FIAMMA
Table of Contents
LED lighting kit
Installation and usage instructions
LED SENSOR DOOR LIGHT
98655A884
LED AWNING LIGHT
98655-848
LED GARAGE LIGHT
98655-883
Check that nothing has been damaged or deformed during transport. In the event
of doubts or questions concerning the installation, use, or limitations of the
product, contact
the dealer. We recommend that the installation is carried out by qualifi ed
personnel and in compliance with current local regulations.
COMFORT – Tech
Only For LED Sensor Door Light
When the individual gets close to the product at a distance between 3
and 5 meters, the sensor gives the switching on pulse within one second. The
light turns off within 60 seconds when the presence is no longer detected.
In case of problems please contact your local dealer. Consult our
website for spare parts drawing.
https://www.fiamma.it/en/led-en
Read the following instructions and warnings carefully; failure to observe
these installation and usage instructions as well as the laws for driving in
the relevant country may cause severe harm or damage for which the
manufacturer declines all responsibility. The product has been designed and
manufactured exclusively for the illumination of recreational vehicles, is not
suitable for the illumination of home environments. For safety reasons, it is
advisable to always disconnect the negative terminal from the batteries on the
vehicle and then work without power during installation. It is suggested to
connect the power cable to the fuse box or to the terminal board and not
directly to the battery. Use the correct fuse for connection to the vehicle
power supply according to EN 1648-1 and EN 1648-2. Installing an oversized
fuse can cause overheating which can result in a short circuit or malfunction
of the entire electrical equipment. Choose the safest and shortest
installation for the power cable. Reduce the length of the power cable as
necessary. Use only cable clamps suitable for the diameter of the power cable
for connection to the terminal board. If incorrect terminals are used, this
could cause a voltage drop and increase the formation of heat on the terminal.
It is strictly forbidden to go around with the LED lights on; connect the
power supply in order to inhibit current fl ow while the vehicle is running. We
do not recommend prolonged periods of viewing at close proximity of the LED
strip. The manufacturer will not be held responsible for claims for damages
resulting from the following:
– Defective installation or connection of the product.
– Damage to the product is caused by mechanical infl uences and overvoltage.
– Alterations on the device without the express authorization of the
manufacturer.
EU Declaration of Conformity (DoC)
We,
Company name: Fiamma S.p.A.
Postal address: Via San Rocco, 56
Postcode and city: Cardano al Campo – (Varese)
Telephone number: 0311/709111
E-mail address: fiamma@fiamma.it
Declare that the DoC is issued under our sole responsibility and belongs to
the following product:
Apparatus model / Product: Lighting systems
Trademark: Fiamma
Model /Type:
98655-850
98655-902
98655-914
98655-915
98655-848
98655-883
98655A884
98655-607
98655-849
98655-886
98655-471
98655Z040
98655Z051
98655-885
98655Z098
98655Z099| Rafter Led
Rafter Led Caravanstore
Led Awning Case
Kit Led Awning Case 50
Led Awning Light
Led Garage Light
Led Sensor Door Light
Led Awning Light Gutter
Awning Arms Led
Led Step
Kit Awning Led
Kit Led Strip Awning
Kit Led Strip Awning High Brightness
Led Warning Solar
Kit Led F65 Eagle
Kit Led F45 Eagle
---|---
The object of the declaration described above is in conformity with the relevant Union harmonization legislation:
- 2014/30/EU Electro Magnetic Compatibility Directive (EMCD).
- 2014/35/EU Low Voltage Directive (LVD).
- 2011/65/EU Restriction of the use of certain hazardous substances Directive (RoHS Directive).
- 2012/1194EU Implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for directional lamps, light-emitting diode lamps, and related equipment.
- 2012/874/EU Supplementing Directive 2010/30/EU of the European Parliament and of the Council with regard to energy labeling of electrical lamps and luminaires.
- EN 60529 (1991) + A1 (2000) The IP code or Ingress Protection ratings are defined in an international standard (IP grade 44)
- IEC 62471:2006 Photobiological safety of lamps and lamp systems.
The following harmonized standards and/or technical specifications have been applied
Warranty Fiamma
In case of defects with regards to materials and manufacturing, the customer
is entitled to the warranty in accordance with local laws and regulations of
the country in which the product was purchased.
Fiamma S.p.A. – Italy
Via San Rocco, 56
21010 Cardano al Campo (VA)
All rights reserved.
Fiamma S.p.A.
reserves the right to modify at any time,
without notice, prices, materials,
specifi cations and models or to cease
production of any model.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>