LUTEC 12513LE4-SL LED Solar Post Lantern Owner’s Manual
- June 12, 2024
- LUTEC
Table of Contents
LED Solar Post Lantern
Owners Manual
Model #12513LE4-SL/6951301053/6951301213
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Solar Panel Top | 1 |
| A1 | Thumbscrews | 2 |
| A2 | Battery-Replacement model # 9700356000 | 1 |
| A3 | Ribbon | 1 |
| A4 | Battery Cover | 1 |
| A5 | Battery Cover Screw | 1 |
| B | Lamp Head | 1 |
| B1 | Solar LED Bulbs-Replacement Model # 9700357000 | 4 |
| B2 | Set Screw 1 | 1 |
| C | Top Pole | 1 |
| C1 | Set Screw 2 | 1 |
| D | 1/8 in Allen Wrench | 1 |
| E | Middle Pole | 1 |
| F | Base | 1 |
| F1 | Base Screws | 3 |
| G | 13/32 in Cap Nuts | 3 |
| H | 13/32 in Washers | 3 |
| I | Concrete Mounting Bracket | 1 |
| J | Anchor Bolts | 3 |
| K | Ground Base Insert | 1 |
| L | 8 5/16 in Small Ground Stakes | 3 |
| M | 17 1/2 in Large Ground Stake | 1 |
| N | Turn Rod | 1 |
| O | 13/32 in Nuts | 3 |
| P | 13/32 x 2 3/16 in Hex Bolts | 3 |
| Q | 3/16 x 7/8 in Ground Stake Screws | 3 |
| R | 2 1/2 in Hex-head Self-drilling Screws | 3 |
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
WARNING: The solar panel “Post Light” requires sunlight to charge the
batteries and should be installed in an area with a minimum of 8 hours of
direct sun exposure.
Note: Charging conditions differ by time zone locations and affects total
hours of light discharge.
Note: Batteries may have become depleted due to lack of sunlight for an
extended period causing the bulbs to not illuminate. Please place the solar
head in direct sunlight for at least 6 hours prior to assembly.
PREPARATION
Before beginning to assemble or installing lighting fixture, make sure all
parts are present. Compare parts with package contents list and hardware
contents list. If any part is missing or damaged, do not attempt to assemble,
install or operate the product.
Estimated Assembly Time: 30-60 minutes.
Tools Required for Assembly: Flathead Screwdriver, Phillips Screwdriver,
Adjustable Wrench/Pliers 1/2 in Wrench, ladder and hammer.
DETERMINE DESIRED INSTALLATION-PERMANENT CONCRETE PAD OR GROUND STAKE
INSTALLATION: PERMANENT CONCRETE PAD
Thread three Anchor Bolts (J) into the Concrete Mounting Bracket (I) allowing for 5 cm (2 in) above the Mounting Bracket. Excavate a hole in the ground that measures at minimum 25.4 cm (10 in) in diameter and has a minimum depth of 12.7 cm (4 in).
Fill the hole with concrete and insert the Concrete Mounting Bracket (I) and
Anchor Bolts (J) before the concrete dries. Allow concrete to dry before
installing Pole Assembly.
Note: The concrete and the Concrete Mounting Bracket (I) should be at
GROUND LEVEL with the Anchor Bolts (J) 2 inches above the ground.
INSTALLATION: GROUND STAKE
Install three Hex Bolt (P) into Ground Base Insert (K), and tighten with Nut (O).
Attach the Large Ground Stake (M) to the Ground Base Insert (K) by screwing three Ground Stake Screws (Q) tight with Phillips screwdriver. Then insert Turn Rod (N).
Turn ground stake assembly clockwise by using Turn Rod (N) into the dirt until
Ground Base Insert (K) is tight against the dirt. Insert and pound the three
smaller Ground Stakes (L) into the dirt with a hammer (not included).
Note: Make sure the bubble in the level found at the top of the Ground
Stake (M) is centered and level so the Post Assembly is in a perfect vertical
position.
ASSEMBLY INSTRUCTIONS
Remove the preassembled Set Screw (C1) from Top Pole (C) and screw Top Pole (C) clockwise onto Middle Pole (E). Re-insert Set Screw (C1), then tighten with Allen Wrench (D). Remove the preassembled 3 Base Screws (F1) from Base (F) with a Phillips screwdriver (not included). Save for later use.
Secure Middle Pole (E) to Base (F) with Base Screws (F1). Tighten with a
Phillips screwdriver.
Remove Thumbscrew (A1), then detach Solar Panel Top (A) from Lamp Head (B).
Take out Solar LED Bulbs (B1) from their shipping boxes.
Install Solar LED Bulbs (B1), and pull off Ribbon (A3) and discard. Turn ON
the switch in Solar Panel Top (A).
Warning: LED lights will not automatically turn on unless the battery has
been charged and it is dark outside. You can test the lights by placing the
empty box upside down over the Post Light Head. Once darker, the LED lights
should turn on in several seconds.
Attach Solar Panel Top (A) to Lamp Head (B) with the previously removed two
Thumbscrews (A1).
Tighten with flathead screwdriver (not included). Carefully screw the lamp
head onto Top Pole (C), securing with the preassembled Set Screw (B2). Tighten
with Allen Wrench (D).
With the help of another person, place the pole assembly over Concrete
Mounting Bracket (I) and Anchor Bolt (J). Secure with Cap Nut (G) and Washer
(H). Tighten with a 1/2 inch wrench (not included).
CAUTION: Allow the concrete to dry before installing the pole assembly.
With the help of another person, place the pole assembly over Ground Base
Insert (K). Secure with Cap Nut (G) and Washer (H).
Tighten with a 1/2 inch wrench (not included).
Installation: Wood Deck
-
Mark 3 points on the deck by using the fixture base holes.
CAUTION: The thickness of the deck must be greater than 10mm or about 1/2″ thick. -
Drill with a suitable drill bit.
-
Secure the pole base assembly to the deck by tightening 3 hex-head self-drilling screws (R).
MAXIMIZING SOLAR LIGHT POST PERFORMANCE
Charging: Charge in direct sunlight for 8-10 hours.
Location: Choose location with minimum 6-8 hours sunlight. When choosing a
spot for your solar light, ensure that the device is not placed near nighttime
light sources such as porch lighting or street lighting.
Dusk To Dawn: The light will not activate during daylight hours. At sundown
the light will go on automatically and last approximately 6-8 hours Cleaning
solar panels: It is important that dirt and debris is kept off of the solar
panel to the greatest extent possible. A dirty solar panel will not fully
charge the battery and thus shorten the battery life.
Battery replacement: Generally speaking, the rechargeable battery should be
replaced every two years in order to maintain the maximum capacity. Please
refer to the specs for max charge cycles.
Note: Run times and lighting performance will vary depending upon
sunlight and weather conditions.
CAUTIONS: BATTERY INSTRUCTIONS
- Always purchase the correct size and grade of battery by ordering the replacement battery part number found in the Parts Description page.
- Ensure the batteries are installed correctly.
- Remove batteries from equipment which is not to be used for an extended period of time.
For recycling and disposal of batteries to protect the environment, please check the internet or your local phone directory for local recycling centers and / or follow local government regulations.
Warning: The supplied LED bulbs have been specially developed for use with
the solar post light model 12513LE4-SL/6951301053/6951301213 and must be
replaced with model 9700357000.
The use of any other type bulbs will not function in the fixture.
Remove Thumbscrew (A1) then detach Solar Panel Top (A) from Lamp Head (B).
Turn off the power switch in Solar Panel Top (A).
Remove the
preassembled Battery Cover Screw (A5) from the Battery Cover (A4) with a
Phillips screwdriver (not included). Then remove the Battery Cover (A4).
Remove the old Battery (A2) and unplug the black battery cord. If an LED bulb
is broken, remove the broken Solar LED Bulb (B1) and replace.
Plug new black battery cable into light fixture. Insert new
battery into battery compartment by carefully placing battery cable into the
cable storage area under battery. Install new LUTEC LED bulb. Attach the
Battery Cover (A4) to Solar Panel Top (A) with Battery Cover Screw (A5)
removed in step 3. Tighten with a Phillips screwdriver (not included).
Turn ON the switch in Solar Panel Top (A). Attach Solar Panel Top (A) to Lamp
Head (B) with the two Thumbscrews (A1). Tighten with flathead screwdriver (not
included).
CARE AND MAINTENANCE To
clean and wipe with a damp, non-abrasive cloth.
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
|---|---|---|
| The light will not go on. | 1.Switch OFF. |
2.The battery is completely discharged.
3.DUSK TO DAWN activited.
4.The bulb is loose.
5.Interference from other light source.
6.The battery is not charged| 1.Set to ON.
2.Charge for 6-8 hours in direct sunlight.
3.Check at night.
4.Re-tighten the bulb.
5.Relocate the solar post light.
6.Make sure the solar panel is in direct sunlight.
The fixture shakes in high winds.| 1.The mounting bracket could be loose.
2.The insert may be loose.
3.The screws and cap nuts may be secured incorrectly.| 1.Make sure the
mounting bracket screws are tightened.
2.Make sure the insert is assembled completely and tightly.
3.Make sure the screws and cap nuts were secured tightly.
The lights come on during the daylight.| 1. The light may be installed
in a dark location.| 1. Relocate to sunny location.
YEAR LIMITED WARRANTY
If this product fails due to a defect in materials or workmanship within three
(3) years (Battery and bulbs excluded) from the date of purchase, return it
along with proof of date of purchase and it will be replaced with the same or
comparable model free of charge by LUTEC USA LLC..
This warranty is void if damage or defect has resulted from accident, abuse,
misuse or faulty repair. This warranty gives you specific legal rights and you
may have other rights that vary from state to state.
LUTEC USA LLC:
149B Houston Rd Troutman NC 28166
Ningbo UTEC Electric Co.,LTD
CN8, Far East Industry Park, Yuyao, China
www.lutec.com
support@lutec.com
Please call our Customer Service line
at877-714-8669
for assistance Monday – Friday 9 a.m. to 5 p.m. EST
Printed in China
Documents / Resources
|
LUTEC 12513LE4-SL LED Solar Post
Lantern
[pdf] Owner's Manual
12513LE4-SL, 6951301053, 6951301213, 12513LE4-SL LED Solar Post Lantern, LED
Solar Post Lantern, Solar Post Lantern, Post Lantern, Lantern
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>