Fanvil i16SV-02P SIP Intercom Installation Guide

June 15, 2024
Fanvil

Fanvil LOGO i16SV-02P SIP Intercom
Quick Installation GuideFanvil i16SV 02P SIP
Intercomwww.fanvil.com

Package Contents

| SIP Intercom
---|---
| Quick Installation Guide
| Screw and tool
| Connector
| Mounting Template

Physical specification

Device Size 195 x 120 x 40 (mm)
  1. PanelFanvil i16SV 02P SIP Intercom - Panel
  2. Interface description
    Open the rear case of the device, there is a row of terminal blocks for connecting the power supply, electric lock control, etc. The connection is as follows: Fanvil i16SV 02P SIP Intercom - Interface
description

Serial number| Description| Wiring port description(example above)
---|---|---
①| Ethernet interface: standard RJ45 interface, 10/100M adaptive, it is recommended to use five or five types of
network cable|
②| Power interface: 12V/1A input| Left positive, right grounded
③, ⑤| Two groups of short-circuit input detection interfaces: for connecting switches, infrared probes, door magnets, vibration sensors and other input devices| Left IN, right OUT
④, ⑥| Two groups of short-circuit output control interface: used to control electric locks, alarms, etc.| Left (NC): Normally Close Contact
Center (COM): Common Contact
Right (NO): Normally Open Contact
⑦| Recording output interface: Mix the device and the sound of the far-end call. One is the recording signal line, and the other is the ground line (be sure to ground the line, otherwise there will be noise)| Left grounded, right recording output
⑧| External active speaker interface: external active speakers for audio power amplification. One is the audio signal line, and the other is the ground line (be sure to ground the line, otherwise there will be noise)| Left grounded, right external active speaker

Installation Diagram

  1. Use built-in screw tool to remove the surface shell;
  2. Based installation dimensions, mounting hole in the wall to draw, use an electric drill holes lay;
  3. The white rubber plugged into the wall and the bottom fixed with screws to the wall;
  4. After connecting the power cord and network cable, screw the surface shell fixed.

Fanvil i16SV 02P SIP Intercom - Diagram

Searching device

There as shown below to search the device.
Methods 1:
Open the iDoorPhone Network Scanner. Press the Refresh button to search the device and find the IP address.

Fanvil i16SV 02P SIP Intercom - device

Method 2:
Long press DSS key for 3 seconds(after power-on for 30 seconds), and when the speaker beeps rapidly, press DSS key again quickly, the beeps stop ,the intercom will report the IP address by itself.
Method 3:
In addition, device provides the device surface DSS key operation to switch IP address acquisition mode: In the standby mode, long-press the DSS key for 3 seconds and the beep will last for 5 seconds. Within 5 seconds, press the DSS key three times quickly to switch to the network mode.
a. If it is in the mode of DHCP and doesn’t receive the IP address, switch it to the mode of static IP (192.168.1.128), broadcast the IP address after the successful switch.
b. If it is in the mode of static IP address (192.168.1.128), switch it to the DHCP mode, broadcast the IP address after the successful switch.
c. If it is in the mode of DHCP and obtain the IP address, the mode will not be switched and directly broadcast the IP.
Default Setting

Default DHCP Client Enabled by default Static IP address 192.168.1.128
Voice broadcast IP address Hold the DSS key for 3 seconds, then press the DSS
key again. Default Web port 80

Fast settings

Step 1:Log in to the device page
Use the web browser input IP (for example: http://192.168.1.128 ) access.
The default user and password are admin.

Fanvil i16SV 02P SIP Intercom - Fast settings

Step 2: Set SIP account
Set SIP server address, port, user name, password and SIP user with assigned SIP account parameters.
Select “Activate”, and then click [Apply] to save this setting.

Fanvil i16SV 02P SIP Intercom - SIP account

Step 3: Set the volume (if not connected can skip)
Intercom settings => Media Settings => Media Settings
Set the device volume size, as shown below, click [Apply].
Speakerphone volume setting: set the speaker volume of normal calls.
Handsfree Mic Gain: set the microphone volume of call.

Fanvil i16SV 02P SIP Intercom - Mic Gain

Step 4: Set function key (if not connected can skip)
Set the function key as shown below for a quick start, click [Apply] to save this settings.
Type: Memory key
Number 1 (Value): the function key will dial to this number 1
Number 2 (Value 2): if number 1 is unavailable, it will be forwarded to number 2.
Subtype: speed dial
Line: working line

Fanvil i16SV 02P SIP Intercom - working line

Step 5: Set the security function
1 set of short-circuit input and output settings, tamper alarm server settings.

Fanvil i16SV 02P SIP Intercom - security function

Fanvil LOGO

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals