SEBSON ES T4 1027 Recessed Aluminum Spotlight Can Instruction Manual

SEBSON ES T4 1027 Recessed Aluminum Spotlight Can

Product Information

Specifications:

• Product Model: ES_T4_1027_SILVER, ES_T5_1027_WHITE, ES_T24_1027_BLACK
• Intended Use: Suitable for installation in ceilings or walls
• Operating Voltage: 230V AC 50Hz
• Maximum Power Consumption: 50W
• Protection Class: IP20

General Safety Information

• The installation of this product must be done by a qualified person according to the valid regulations for electrical installation.
• If the power cables are damaged or come into contact with wetness, immediately disconnect the product from the power supply and ensure that it cannot be switched on again.
• Keep this product away from children and animals.
• Do not direct the light beam of the product directly at people or animals to prevent fire damage or eye damage. Avoid looking directly into the light source.
• Modifying the product is not allowed as it may affect its proper and safe functioning and invalidate the warranty claim.
• The manufacturer does not accept responsibility for injuries or damage resulting from improper use of this product.
• This product is only suited for indoor use and not for outdoor use.
• Protect the product from external damage, heavy dirt, moisture, and excessive heat.

Product Usage Instructions

Installation:

• Before installing the product, please read and follow the safety information and technical specifications provided in the user manual.
• Ensure proper air circulation at the installation location of the mounting frame to prevent the risk of fire.
• Minimum distance between the recessed lights: 500mm
• Diameter of the installation hole: 75mm (minimum 73mm, maximum 77mm)

Cleaning:

• Prior to cleaning the product, interrupt the power circuit by switching off the circuit breaker.
• Use a soft, dry cloth to clean the product. Do not use any abrasive or corrosive cleaning agents.

FAQ:

• Q: Can I install this product outdoors?
  A: No, this product is only suitable for indoor use and should not be installed outdoors.

• Q: Can I modify the product to fit my specific needs?
  A: No, modifying the product is not allowed as it may affect its proper and safe functioning and invalidate the warranty claim.

• Q: What should I do if the power cables are damaged?
  A: If the power cables are damaged or come into contact with wetness, immediately disconnect the product from the power supply and ensure that it cannot be switched on again. Seek professional assistance to repair or replace the damaged cables.

Thank you for choosing a product of SEBSON. Read the instructions carefully and keep them for looking up before starting this product. A long and failure- free operation can only be guaranteed if the installation and start-up is done properly. Before starting up this product, please check for external damage. In case of visible external damage, we immediately dis-advise the start-up of this product! Please remove all packaging material of this product before the first start-up an and check the content for completeness!

Intended use:
This SEBSON mounting frame is suitable for installation in e.g. ceilings or walls.

General safety information

• Danger: The installation of this product may be done only by a qualified person according to the valid regulations for electrical installation!
  Danger: If the power cables are damaged or come into contact with wetness, immediately disconnect the product from the power supply and ensure that it cannot be switched on again!
  Danger: Please keep this product away from children and animals.
  Caution: Please set up the light beam of the light never directly at people or animals to prevent fire damage or eye damage and avoid looking directly into the light source!

  • The remodeling of this product is not allowed! The proper and safe functioning of the device can no longer be guaranteed if it is modified! In addition, this will invalidate the warranty claim!
  • The manufacturer does not accept any responsibility for injuries or damage resulting from improper use of this product!
  • Any other use than the description may result in damage to the product. So the dangers are such as electric shock, short circuit, fire, etc.
  • This product is only suited for indoor use and not for outdoor use!
  • We reserve the right to make changes to the product, the packaging, or the operating instructions as well as printing errors.
  • The mounting frames are suitable for use with matching LED or conventional halogen bulbs. Please observe the specifications in the “Technical Data”!
  • Protect the product from external damage, heavy dirt, moisture, and excessive heat!
  • In order that the warranty claim does not expire please use only the supplied items. Repairs may only be done by an expert and only by using original spare parts!
  • In commercial institutions, the accident prevention regulations of the professional trade association for electrical equipment and facilities must be adhered to.

Instruction for installation

• Danger: Before installing make sure that the circuit is interrupted! For installation, the work on the mains voltage is required. Remove the associated mains fuse or deactivate the switch fuse! Check by using a voltage tester if the line is de-energized. Make sure that the current circuit will not be closed during the installation! There is a danger to life here!
• Danger: Do not install the mounting frame on metallic surfaces! Since metal has an electroconductive property and therefore a risk of electric shock cannot be excluded, we strongly advise against installation on metallic surfaces!
• Danger: To prevent the heat produced by the lamps from accumulating, sufficient air circulation must be ensured at the installation location of the mounting frames. Otherwise, there is a risk of fire!
  • Please observe the safety instructions and technical data before installing this product!
  • Note on installation:
  • L: Live wire (black or brown)
  • N: Neutral conductor (blue or grey)
  • The distance between the recessed lamp and the surface to be illuminated should be at least 50cm.
  • When mounting several mounting frames next to each other, a minimum distance of 50cm must be observed.

Installation recommendation:

Minimum distance between lights:| 500mm
Mounting hole:| 75mm (min.73mm, max.77mm)
Maximum thickness of mounting surface:| Max. 22mm

Technical Data

Technical Data:

Operating voltage:| 230V AC 50Hz
Maximum load:| Max.50W
Electrical protection:| IP20

Information for private households (WEEE)

The Electrical and Electronic Equipment Act (WEEE) contains a large number of requirements for the handling of electrical and electronic equipment. The most important ones are summarised here.

1. Separate collection of waste equipment
   Old, worn-out or defective electrical and electronic equipment is referred to as waste equipment. These devices must not be disposed of in the normal household waste or together with the residual waste. The devices should be transferred to special collection and return systems.

2. Batteries and rechargeable batteries as well as illuminants
   As a rule, owners of WEEE shall separate spent batteries and accumulators that are not enclosed in the WEEE, as well as light sources that can be removed from the WEEE without causing damage, from the WEEE before handing it over to a collection point. This does not apply if WEEE is prepared for reuse with the participation of a public waste management authority. Batteries or rechargeable batteries that contain harmful substances are marked with the symbol of a crossed-out dustbin and must not be disposed of in household waste. Below the dustbin symbol is the chemical name of the pollutant – in the example below “Cd” for cadmium. “Pb” stands for lead, “Hg” for mercury: If disposed of improperly, the substances contained in the batteries may cause hazards to health and the environment. The hazards are averted by the separate collection and proper disposal of used batteries.

3. Options for returning old appliances
   Owners of WEEE from private households can hand it in free of charge at the collection points of the public waste management authorities or at the take- back points set up by manufacturers or distributors.

4. Data privacy notice
   Old devices often contain sensitive personal data. This applies in particular to information and telecommunications technology devices such as computers and smartphones. In your own interest, please note that each end user is responsible for deleting the data on the end-of-life devices to be disposed of.

5. Meaning of the “crossed-out dustbin” symbol
   The symbol of a crossed-out dustbin regularly displayed on electrical and electronic equipment indicates that the respective device must be collected separately from unsorted municipal waste at the end of its service life.

Cleaning

Danger:
Before start cleaning the product interrupt the current circuit by switching off the circuit breaker or unscrewing the fuse! Use a slightly moistened cloth for cleaning. In order not to damage the product, it is essential to avoid water penetrating into the housing! Never clean the device under running water! Do not use solvent-containing cleaner for cleaning.

Contact Information

SEBSON

• Sebastian Sonntag Walter-Behrendt-Str.10 44329 Dortmund Germany.
• support@sebson.de VAT-Nr.: GB179436663 WEEE-Reg.-ID.: 500617.

References

• Informationen für Verbraucher | SEBSON

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>